Page 1
Consumer Services Warranty ug603-2559_3574-3576_1005.indd 1 ug603-2559_3574-3576_1005.indd 1 CleanView B A G L E S S U S E R ’ S G U I D E 3574/3576 SERIES Safety Instructions Product View Assembly Instructions Operation / Special Tools 8-12 Maintenance 12-13 Troubleshooting Replacement Parts...
Your BISSELL CleanView II is well made, and we back it with a limited comprehensive one-year warranty. We also stand behind it with a knowledgeable, dedicated Consumer Services Department, so, should you ever have a problem, you’ll receive fast, considerate assistance.
■ Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord. ■ Do not handle vacuum cleaner or plug with wet hands. ■ Do not put any object into openings. Do not use with any opening blocked; keep openings free of dust, lint, hair, and anything that may reduce air flow.
How To Put It Together The only tool you’ll need to assemble your vacuum cleaner is a screwdriver. Attach Handle To Vacuum Locate the vacuum Handle and remove the screw packet taped to the base of the Handle. Stand the vacuum upright and slide the base of the Handle firmly into the grooves at the top of the vacuum body.
How To Use Your Vacuum Handle Positions Press the Handle Release Pedal with your foot to place your vacuum in one of three cleaning positions. Upright- For storage and above floor cleaning with tools. Normal Cleaning- Press Handle Release Pedal once. Use for most household floor cleaning tasks.
Special On-Board Tools Your BISSELL CleanView II is not only a pow- erful carpet and rug vacuum cleaner, it’s also a versatile above floor vacuum cleaner when you select one of the special tools. Raise Handle to Upright Position. Grasp the Quick Reach Handle and lift Hose Wand to separate from suction intake opening.
Reassemble and make sure it is completely dry before using again. Cleaning The Inner & Outer Circular Filters Use only BISSELL Style 9 Replacement Filters in your BISSELL CleanView II. Unplug the cleaner from electrical outlet. Remove the Dirt Container as described in the previous section.
Remove the small round Filter and any debris on top of it. Rinse well under warm water, then air dry thoroughly before replacing. Replacing the Post-Motor Filter Use only BISSELL Style 9 Replacement Filters in your BISSELL CleanView II. Unplug the cleaner from electrical outlet.
Check Drive Belt carefully for wear, cuts or stressed areas. Check Air Passageway for obstructions. Remove debris from this area. Replace Drive Belt Use only BISSELL Style 9 Replacement Belts (#32074) in your BISSELL CleanView II. Unplug cleaner from electrical outlet. With Rotating Floor Brush removed from vacuum cleaner (Steps 1-4 of Check Rotating Floor Brush and Drive Belt), grasp old Drive Belt and remove from Motor Pulley.
Page 11
Clearing Clogs Low suction, poor pickup, or no suction may be due to a clog in the vacuum cleaner. If you notice a change in the sound of the motor or a reduction in the spinning action in the Dirt Container, check for clogs.
Troubleshooting Vacuum cleaner won’t run Possible Causes Power cord not plugged in Blown fuse/tripped breaker Vacuum cleaner won’t pick up dirt Possible Causes Incorrect Height Adjustment Hose not attached to suction opening Twist ‘n Snap Hose not securely attached. Crack or hole in Hose...
Page 13
Dirt Container full Filters missing or installed incorrectly Dirt Container installed incorrectly Filter Cup installed incorrectly If suggested solutions do not correct the problem, call: BISSELL Consumer Services ug603-2559_3574-3576_1005.indd 13 ug603-2559_3574-3576_1005.indd 13 Remedies Position correctly and lock in place Check and clean Inner and Outer...
Page 14
Replacement Parts – BISSELL Cleanview II Series You may purchase replacement parts from your retailer, by calling BISSELL Consumer Services or by visiting our website. To locate a retailer near you, or to place an order using Visa, MasterCard, Discover or American Express, call...
Page 15
Grand Rapids, MI 49501 ATTN: Consumer Services Or visit the BISSELL website - www.bissell.com When contacting BISSELL, have model number of unit available. Please record your Model Number: ___________________ Please record your Purchase Date: ___________________ NOTE: Please keep your original sales receipt. It is your warranty.
Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, upon receipt of the product BISSELL Homecare Inc. will repair or replace (with new or remanufactured components or products), at BISSELL’s option, free of charge from the date of purchase by the original purchaser, for one year any defective or malfunctioning part.
Need help?
Do you have a question about the 3574 Series and is the answer not in the manual?
Questions and answers