Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Dahua DH-HAC-HFW1200T-A
Summary of Contents for Dahua DH-HAC-HFW1200T-A
- Page 1 HDCVI Bullet Camera Lite User’s Manual V1.0.0...
-
Page 2: Foreword
Foreword General This user’s manual (hereinafter referred to be "the Manual") introduces the functions, installation, and operations of the camera. Safety Instructions The following categorized signal words with defined meaning might appear in the Manual. Signal Words Meaning Indicates a medium or low potential hazard which, if not avoided, WARNING could result in slight or moderate injury. - Page 3 website. If there is inconsistency between paper manual and the electronic version, the electronic version shall prevail. All the designs and software are subject to change without prior written notice. The product updates might cause some differences between the actual product and the Manual. Please contact the customer service for the latest program and supplementary documentation.
- Page 4 Important Safeguards and Warnings Electrical Safety All installation and operation should conform to your local electrical safety codes. The power source shall conform to the requirement of the Safety Extra Low Voltage (SELV) standard, and supply power with rated voltage which conforms to Limited power Source requirement according to IEC60950-1.
- Page 5 The surface of the image sensor should not be exposed to laser beam radiation in an environment where a laser beam device is used. Do not provide two or more power supply sources for the device; otherwise it might damage the device.
- Page 6 Regulatory Information FCC Information Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC conditions: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: This device may not cause harmful interference.
-
Page 7: Table Of Contents
Table of Contents Foreword ..............................I 1 Introduction ............................1 1.1 General............................1 1.2 Features ............................1 2 Design ..............................2 2.1 Dimension ............................. 2 2.2 Cable ............................. 4 3 Installation .............................. 6 3.1 Installing Model A (1) and Model A (2) ..................6 3.2 Installing Model B .......................... -
Page 8: Introduction
Introduction General This series of products comply with the HDCVI standard and support the transmission of video and control signal over coaxial cable. They produce video signal with megapixel resolution and require XVR device that comply with the HDCVI standard to achieve high speed, long distance, and zero lag transmission of the signal. -
Page 9: Design
Design Dimension Figure 2-1 Model A (1) (mm [in.]) Figure 2-2 Model A (2) (mm [in.]) Figure 2-3 Model B (mm [in.]) Figure 2-4 Model C (mm [in.]) Figure 2-5 Model D (mm [in.]) Design 2... - Page 10 Figure 2-6 Model E (mm [in.]) Figure 2-7 Model F (mm [in.]) Figure 2-8 Model G (mm [in.]) Figure 2-9 Model H (mm [in.]) Figure 2-10 Model I (1) (mm [in.]) Figure 2-11 Model I (2) (mm [in.]) Design 3...
-
Page 11: Cable
Figure 2-12 Model J (mm [in.]) Figure 2-13 Model K (1) (mm [in.]) Figure 2-14 Model K (2) (mm [in.]) Figure 2-15 Model L (mm [in.]) Cable Cable type might vary with different cameras, and the actual product shall prevail. Design 4... - Page 12 Figure 2-16 Cable list For more information about cable ports, see Table 2-1; for the operation method of ④ (DIP switch), see Table 2-2. Table 2-1 Cable function Port Name Function ① Inputs 12V DC power. Please be sure to supply power as instructed in the Power Input Manual.
-
Page 13: Installation
Installation Make sure the mounting surface is strong enough to hold at least three times of the camera weight. The following figures are for reference only, and the actual product shall prevail. Installing Model A (1) and Model A (2) Figure 3-1 Model A (1) and Model A (2) installation Table 3-1 Installation item list... -
Page 14: Installing Model B
Figure 3-2 Model A (1) and Model A (2) adjustment In the PTZ setting interface (Figure 4-5), click + or – at Zoom and Focus to adjust the zoom and focus until you get clear image. For Model A (2) ... -
Page 15: Installing Model C
Item Item ③ ④ Expansion bolt Mounting surface Step 1 Confirm the position of screw holes (and the cable outlet hole if it needs to go through the mounting surface④) and drill them on the mounting surface④, and then insert the expansion bolts③... -
Page 16: Installing Model D
Step 3 Connect the device① to power source and the XVR device, and the live view screen is displayed. Step 4 Loosen the locking screws and aim the lens to the ideal angle, and then fasten them, see Figure 3-7. Figure 3-7 Model C adjustment Installing Model D... -
Page 17: Installing Model E
Figure 3-9 Model D adjustment Installing Model E Figure 3-10 Model E installation Table 3-5 Installation item list Item Item ① ② Device Self-tapping screw ③ ④ Expansion bolt Mounting surface Step 1 Confirm the position of screw holes (and the cable outlet hole if it needs to go through the mounting surface④) and drill them on the mounting surface④, and then insert the expansion bolts③... -
Page 18: Installing Model F
Installing Model F Figure 3-12 Model F installation Table 3-6 Installation item list Item Item ① ② Device Self-tapping screw ③ ④ Expansion bolt Mounting surface Step 1 Confirm the position of screw holes (and the cable outlet hole if it needs to go through the mounting surface④) and drill them on the mounting surface④, and then insert the expansion bolts③... -
Page 19: Installing Model G
Installing Model G Figure 3-14 Model G installation Table 3-7 Installation item list Item Item ① ② Device Self-tapping screw ③ ④ Expansion bolt Mounting surface Step 1 Confirm the position of screw holes (and the cable outlet hole if it needs to go through the mounting surface④) and drill them on the mounting surface④, and then insert the expansion bolts③... -
Page 20: Installing Model H
Installing Model H Figure 3-16 Model H installation Table 3-8 Installation item list Item Item ① ② Device Self-tapping screw ③ ④ Expansion bolt Mounting surface Step 1 Confirm the position of screw holes (and the cable outlet hole if it needs to go through the mounting surface④) and drill them on the mounting surface④, and then insert the expansion bolts③... -
Page 21: Installing Model I (1) And Model I (2)
Installing Model I (1) and Model I (2) Figure 3-18 Model I (1) and Model I (2) installation Table 3-9 Installation item list Item Item ① ② Device Self-tapping screw ③ ④ Expansion bolt Mounting surface Step 1 Confirm the position of screw holes (and the cable outlet hole if it needs to go through the mounting surface④) and drill them on the mounting surface④, and then insert the expansion bolts③... -
Page 22: Installing Model J
Open the bottom cover, and then twist to loosen the zoom and focus levers, turn them left or right to adjust the focus and zoom until you get clear image, see Figure 3-20. Figure 3-20 Model I (2) image adjustment Lock the levers and bottom cover, and then fasten the locking screws. -
Page 23: Installing Model K (1) And Model K (2)
Figure 3-22 Model J adjustment 3.11 Installing Model K (1) and Model K (2) Figure 3-23 Model K (1) and Model K (2) installation Table 3-11 Installation item list Item Item ① ② Device Self-tapping screw ③ ④ Expansion bolt Mounting surface Step 1 Confirm the position of screw holes (and the cable outlet hole if it needs to go through... -
Page 24: Installing Model L
Figure 3-24 Model K (1) and Model K (2) adjustment In the PTZ setting interface (Figure 4-5), click + or – at Zoom and Focus to adjust the zoom and focus until you get clear image. For Model K (2) ... - Page 25 Step 1 Confirm the position of screw holes (and the cable outlet hole if it needs to go through the mounting surface④) and drill them on the mounting surface④, and then insert the expansion bolts③ in the screw holes. Step 2 Align the screw holes on the bracket to those on the mounting surface④, and then pull the cable out through mounting surface or the side cable tray.
-
Page 26: General Configuration
General Configuration Power up the camera and connect it to the XVR device with coaxial cable, and then the live view screen is displayed. The following instructions will guide you to configure your camera. The number of the coaxial port on XVR will display at the lower left corner of each window ... -
Page 27: Setting Audio Input
Figure 4-2 Main menu interface Right-click anywhere on the screen to return to the previous interface until it goes back to the live view screen. Setting Audio Input Audio signal acquisition is available on select models. Step 1 In the Main Menu interface (Figure 4-2), select CAMERA > ENCODE > Encode. The Encode setting interface is displayed. -
Page 28: Operating Osd Menu
Step 3 In the Main Stream column, click More Setting. The More Setting interface is displayed, see Figure 4-4. Figure 4-4 More setting interface Step 4 In the More Setting interface, you can configure the audio settings. Enable Audio Encode function. ... - Page 29 Figure 4-6 PTZ setting options Step 4 Click The MENU OPERATION panel is displayed. See Figure 4-7. The OSD menu of the corresponding camera is displayed on the live view screen. Figure 4-7 Menu Operation panel For the function of the buttons in the MENU OPERATION panel, see Table 4-1. Table 4-1 Menu Operation panel function Button Function...
-
Page 30: Maintenance
Maintenance In order to maintain the image quality and proper functioning of the device, please read the following maintenance instructions carefully and hold rigid adherence. Disassembly and Desiccant Replacement Carefully follow the instructions in the manual when performing any disassembly operation about the device;...
Need help?
Do you have a question about the DH-HAC-HFW1200T-A and is the answer not in the manual?
Questions and answers