Explanation Of Symbols; Contact Information - VOCO CELALUX 3 Directions For Use Manual

13. Explanation of Symbols

Complies with the regulations of the directive 93/42/EEC.
Attention: Please see the documentation that accompanies this product!
This symbol refers to the special disposal of electrical and electronic devices in
EU countries. Please do not discard this device in household garbage. Check
the proper means of disposal in your country at your community recycling or
waste center or at your dealer. Take care to dispose of properly.
This symbol indicates that a product or instrument (here, Celalux 3 Light
134 °C
guides and eye-protector) can be sterilized at the indicated temperature
(134 °C = 275 °F).
Please see the operating manual!
Warning symbol: high intensity LED radiation

14. Contact Information

• In case of problems, please contact or e-mail VOCO.
Annex 1
Guidance and manufacturer's declaration – Electromagnetic emissions
EN 60601-1-2/Table 201
Equipment Group 1 and Class B; per CISPR 11
The Celalux 3 is intended for use in the electromagnetic environment specified below. The
customer or the user of the Celalux 3 should ensure that it is used in such an environment
RF emissions CISPR Group 1 The Celalux 3 uses RF energy only for its internal func-
11 tion. Therefore it's RF emissions are very low and are
not likely to cause any interference in nearby electronic
equipment.
RF emissions CISPR Class B
The Celalux 3 is suitable for use in all establishments,
11
including domestic establishments and those directly
connected to the public low-voltage power supply net-
Harmonic emissions Complies
work that supplies buildings used for domestic purposes.
IEC 61000-3-2
Voltage fluctuations
/ flicker emissions
IEC 61000-3-3
Guidance and manufacturer's declaration – Electromagnetic immunity
EN 60601-1-2 / Table 202
The Celalux 3 is intended for use in the electromagnetic environment specified below. The
customer or the user of the Celalux 3 should ensure that it is used in such an environment.
Immunity Test IEC 60601
Test Level
Electrostatic ±6 kV contact
discharge ±8 kV air
(ESD) IEC
61000-4-2
Radiated RF 3 V/m 80 MHz to
IEC 61000-4-3 2.5 GHz
Electrical ±2 kV for power
fast transient supply lines
/ burst IEC ±1 kV for input /
61000-4-4 output lines
Surge IEC ±1 kV differential
61000-4-5 mode
±2 kV common
mode
Compliance Electromagnetic
Environment Guidance
The device con- Floors should be wood, concrete
tinues to work or ceramic tile. If floors are cov-
regularly and in ered with synthetic material, the
safety. relative humidity should be at
least 30%.
The device con- Field strengths from fixed trans-
tinues to work mitters cannot be predicted
regularly and in theoretically with accuracy. To as-
safety.
sess the electromagnetic environ-
ment due to fixed RF transmitters,
an electromagnetic site survey
should be considered.
The device con- Mains power quality should be
tinues to work that of a typical commercial or
regularly and in hospital environment.
safety.
The device con-
tinues to work
regularly and in
safety.
Conducted RF 3 Veff 150 kHz to The device con-
IEC 61000-4-6 80 MHz tinues to work
regularly and in
safety.
Power fre- 3-100 A/m The device con-
quency tinues to work
(50/60 Hz) regularly and in
safety.
magnetic field
IEC 61000-
4-8
Voltage < 5% U/10 ms
The device can
dips, short
vary from the
interruptions 70% U/0.5 s
required levels of
and voltage
immunity with a
variations on 40% U/0.1 s
duration for as long
power supply
as the device re-
input lines IEC
mains in safety; no
61000-4-11
malfunctions have
been detected and
can be restored to
pre-test status with
the intervention of
the operator
Note:
1. (P) is the maximum output power rating of the transmitter in watts (W) according to the
transmitter manufacturer and (d) is the recommended separation distance in meters (m).
Field strengths from fixed RF transmitters, as determined by an electromagnetic site survey,
should be less than the compliance level in each frequency range (b). Interference may oc-
cur in the vicinity of equipment marked with the following symbol:
2. These guidelines may not apply in all situations. Electromagnetic propagation is affected
by absorption and reflection from structures, objects and people. Field strengths from fixed
transmitters, such as base stations for radio (cellular / cordless) telephones and land mobile
radios, amateur radio, AM and FM radio broadcast and TV broadcast cannot be predicted
theoretically with accuracy. To assess the electromagnetic environment due to fixed RF
transmitters, an electromagnetic site survey should be considered. If the measured field
strength in the location in which the Celalux 3 is used exceeds the applicable RF compli-
ance level above, the Celalux 3 should be observed to verify normal operation. If abnormal
performance is observed, additional measures may be necessary, such as re-orienting or
relocating the Celalux 3.
Recommended separation distances between portable and mobile RF communications equip-
ment and the Celalux 3
This product is intended for use in an electromagnetic environment in which radiated RF distur-
bances are controlled. The customer or the user of the Celalux 3 can help prevent electromag-
netic interference by maintaining a minimum distance between portable and mobile RF com-
munications equipment (transmitters) and the Celalux 3 as recommended below, according to
the maximum output power of the communications equipment.
Celalux 3
EN 60601-1-2 / Table 206
Separation distance according to frequency of transmitter (m)
Rated maximum output 50 kHz-80 MHz
power of transmitter (W) d = 1.2 x √P
0.01 0.12
0.1 0.38
1 1.2
2 1.7
10 3.8
100 12
Portable and mobile RF com-
munications equipment should be
used no closer to any part of the
disposal including cables, than the
recommended separation dis-
tance calculated from the equa-
tion applicable to the frequency of
the transmitter.
Recommended separation
distance 1 :
d = 1.2 √P
d = 1.2 √P 80 MHz to 800 MHz
d = 2.3 √P 800 MHz to 2.5 GHz
Power frequency magnetic fields
should be at levels characteristic
of a typical location in a typical
commercial or hospital environ-
ment.
Mains power quality should be
that of a typical commercial or
hospital environment.
80 MHz-800 MHz 800 MHz-2.5 GHz
d = 1.2 x √P d = 2.3 x √P
Sender Sender
0.12 0.23
0.38
1.2
1.7
3.8
12
Sender
0.73
2.3
3.25
7.3
23
9