Related Manuals for Extron electronics XTP PI 400
Summary of Contents for Extron electronics XTP PI 400
- Page 1 User Guide XTP Power Injector XTP PI 400 Four Port XTP Power Injector 68-2291-01 Rev. F 01 19...
- Page 2 Safety Instructions Safety Instructions • English Инструкция по технике безопасности • Русский WARNING: This symbol, , when used on the product, is intended to ПРЕДУПРЕЖДЕНИЕ: Данный символ, , если указан alert the user of the presence of uninsulated dangerous voltage within the на...
- Page 3 “Extron Safety and Regulatory Compliance Guide” on the Extron website. Copyright © 2016-2019 Extron Electronics. All rights reserved. Trademarks All trademarks mentioned in this guide are the properties of their respective owners. The following registered trademarks ®...
- Page 4 Conventions Used in this Guide Notifications The following notifications are used in this guide: WARNING: Potential risk of severe injury or death. AVERTISSEMENT : Risque potentiel de blessure grave ou de mort. ATTENTION: • Risk of property damage. • Risque de dommages matériels. NOTE: A note draws attention to important information.
-
Page 5: Table Of Contents
Contents Introduction ........... 1 About the XTP PI 400 ......... 1 Features ............. 3 Installation and Operation ......4 Installation ............4 Important Safety Instructions ......4 Installation Overview ........6 Rear Panel Connectors ........6 Twisted Pair Cable Recommendations .... 7 LED Indicators ............ - Page 6 XTP PI 400 Power Injector • Contents...
-
Page 7: Introduction
In this guide, the term “XTP PI 400” is used to refer to the XTP PI 400 Power Injector. This section provides basic information about this guide, the XTP PI 400, and key features of the XTP PI 400. - Page 8 RTS CTS LAN / PoE DISPLAY IPL Pro S1 LAPTOP VOLUME VIDEO MUTE Extron MLC Plus 100 Figure 3. XTP PI 400 Remote Power to IPL Pro, MLC Plus, and TLP Pro Devices XTP PI 400 Power Injector • Introduction...
-
Page 9: Features
XTP extender. • UL/c-UL Listed and CE compliant • 1U, half rack width enclosure Internal universal power supply — The 100-240 VAC, 50-60 Hz, international power • supply provides worldwide power compatibility. XTP PI 400 Power Injector • Introduction... -
Page 10: Installation And Operation
• Only use attachments and accessories specified by the manufacturer. • Unplug this device apparatus during lightning storms or when unused for long periods of time. XTP PI 400 Power Injector • Installation and Operation... - Page 11 Déconnection de l’alimentation — Pour déconnecter le matériel de sa source d’alimentation en toute sécurité, débranchez tous les cordons d’alimentation de l’arrière du matériel ou débranchez l’adaptateur secteur (si débranchable) ou de la prise secteur (prise murale). XTP PI 400 Power Injector • Installation and Operation...
-
Page 12: Installation Overview
Ne connectez pas ces appareils à des données informatiques ou à un réseau de télécommunications. NOTE: The XTP PI 400 does not switch XTP signals. AC power connector — Connect the IEC power cord to this AC power connector. XTP connector — Connect an Extron XTP device, IPL Pro, or MLC Plus to this XTP connector on any of the four port pairs. -
Page 13: Twisted Pair Cable Recommendations
Connector Figure 7. Twisted Pair Cable Configuration Supported cables The XTP PI 400 is compatible with CAT 5e, 6, 6a, and 7 shielded twisted pair (F/UTP, SF/UTP, and S/FTP) and unshielded twisted pair (U/UTP) cable. ATTENTION: • Do not use Extron UTP23SF-4 Enhanced Skew-Free AV UTP cable or STP201 cable. -
Page 14: Led Indicators
XTP POWER INJECTOR Figure 8. Front Panel Features Front panel power LED indicator — Lights to indicate the XTP PI 400 is receiving power. Front panel XTP Power Out LED indicators — Light when the XTP PI 400 is providing power to XTP devices connected to the XTP PWR connectors. -
Page 15: Mounting
The XTP PI 400 is 1U high and one half rack wide. To mount the device: Turn off or disconnect all equipment power sources. Mount the XTP PI 400 on a table, under a desk using an optional mounting kit, or on a rack shelf (see the sections below for each mounting option). -
Page 16: Rack Mounting
Rack Mounting Mount the XTP PI 400 to an optional Extron rack shelf. To mount the unit on a rack shelf, Half Rack 9.5 inch Box Standard Shelf follow the instructions provided with the shelf accessories. 1U Universal Rack Shelf... - Page 17 Extron Electronics makes no further warranties either expressed or implied with respect to the product and its quality, performance, merchantability, or fitness for any particular use. In no event will Extron Electronics be liable for direct, indirect, or consequential damages resulting from any defect in this product even if Extron Electronics has been advised of such damage.