Fcc Regulatory Safety Notice - Pentair HIGH POWER WIRELESS LINK KIT Installation Manual

FCC Regulatory Safety Notice

FCC non-modification statement:
Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
FCC RF Exposure requirements:
Notice for High Power Wireless Link (FCC ID: 2AHWAQTSHPWETH -
HVIN/MODEL: HPW-WETHLINK: In order to comply with FCC/ISED RF Exposure
requirements, a minimum separation distance of 8 in (20 cm) must be maintained between the
equipment and all persons during normal operation.
Exigences de la FCC en matière d'exposition aux fréquences radio:
Remarquer: pour lien sans fil haute puissance (FCC ID: 2AHWAQTSHPWETH -
HVIN/MODEL: HPW-WETHLINK: Afin de respecter les exigences d'exposition RF de la FCC
/ ISED, une distance minimale de 20 cm doit être respectée entre l'appareil et toutes les
personnes en fonctionnement normal.
Canada - Innovation, Science and Economic Development (ISED)
(ISED: 21176-QTSHPWETH): The Control System and the High Power Wireless (HPW)
Link complies with RSS210 of ISED Canada (2019). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
This Class B digital apparatus complies with Innovation, Science and Economic Development
(ISED) Exempt RSSs. Operation is subject to the following: (1) This device may not cause
interference; and (2) This device must accept interference that may cause undesired operation
of the device.
Le dispositif est conforme à la licence Innovation, Science and Economic Development
(ISED) Canada. Le fonctionnement est soumis à la suivante. (1) Ce ne doit pas provoquer
d'interférences ; et (2) Cet appareil doit accepter les interférences qui peuvent causer un
mauvais fonctionnement de l'appareil.
Cet appareil numérique de classe B est conforme à la norme canadienne ISDE (RSP-100,
section 2.1) et Terminal Equipment Registrations (DC-01, Section 3.). Cet appareil numérique
de la classe B est conforme à la norme NMB-003 du Canada. Le terme «ISED» précédant
le numéro de certification / d'enregistrement signifie uniquement que les spécifications
techniques relatives à l'innovation, à la science et au développement économique ont été
respectées.
Instruction to user: The IntelliCenter
High Power Wireless (HPW) Link has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. The
IntelliCenter, EasyTouch and IntelliTouch Control System High Power Wireless (HPW) Link
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this device does cause harmful interference to radio or television reception, which can be
determined by switching the device off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Note: The user is cautioned that changes and modifications made to the IntelliCenter,
EasyTouch and IntelliTouch Control System without the approval of the manufacturer could
void the user's authority to operate this equipment.
™ , EasyTouch ® and IntelliTouch
High Power Wireless Link Kit Installation Guide
® Control System
3