Turbo E1T Series User Manual
  1. Manuals
  2. Brands
  3. Turbo Manuals
  4. Recording Equipment
  5. E1T Series
  6. User manual

Turbo E1T Series User Manual

Hide thumbs Also See for E1T Series:
Table of Contents

Advertisement

Quick Links

See also: User Manual
TURBO
s.r.l.
Electronic Control Systems for Dust Collectors
e-mail: info@turbocontrols.it
web: www.turbocontrols.eu
TEL. ++39 (0)362 574024 FAX ++39 (0)362 574092
SEQUENCER
SERIES E1T

USER MANUAL

01/03/2016
Manual Release 1.24
Hardware Release 1.3

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the E1T Series and is the answer not in the manual?

Questions and answers

Related Manuals for Turbo E1T Series

Summary of Contents for Turbo E1T Series

  • Page 1: User Manual

    TURBO s.r.l. Electronic Control Systems for Dust Collectors e-mail: info@turbocontrols.it web: www.turbocontrols.eu TEL. ++39 (0)362 574024 FAX ++39 (0)362 574092 SEQUENCER SERIES E1T USER MANUAL 01/03/2016 Manual Release 1.24 Hardware Release 1.3...

  • Page 2: General Description

    General Description Sequencer for controlling the pneumatic cleaning function of industrial dust collection systems. The device has two output relays contacts and two digital input contacts. A large, bright display is provided for reading the timer operation, the active solenoid valves and any alarms in any moment.

  • Page 3: Electric Specifications

    Electric Specifications Electric Power: • 115 Vac ± 10% 50-60 Hz – 25W Important: Read the installation • 230 Vac ± 10% 50-60 Hz – 25W instruction section before • 24 Vac ± 10% 50-60 Hz – 25W (Optional) connecting the device. •...

  • Page 4: Warning Symbols Used In This Manual

    Warning Symbols Used In This Manual The information regarding safety are highlighted using the symbols: Warning-Danger Generic - Warning- Risk – Danger Electric Current Dispose according to the standards for electrical and electronic equipment RAAE Installation Rules Notes and Warnings Protect the device from direct exposure to sunlight.
  • Page 5 The cable glands must be chosen according to the diameter of the cable to be used. The sealing of the press cable is guaranteed by the compression of the rubber gasket that tightens on the outer diameter of the cable. The tightness of the cable gland is guaranteed by the compression of the rubber seal that tightens on the outer diameter of the cable.

  • Page 6: Display / Keypad

    Display / Keypad There are four round buttons on the front panel for controlling the device on the front panel. The display will appear similar to the following when it is turned on. The SET button enables to enter and exit the programming menu, and activate the manual test of solenoid valve selected in function F06.

  • Page 7: List Of Functions

    List Of Functions F02: Solenoid valve activation time. Possible values: 0.05” – 5.00” step 0.01”. Default = 0.20”. F03: Washing pause time between solenoid valves. Possible values: 001” – 999” step 1”. Default = 020”. F04: Number of connected outputs. Possible values: 01 –...
  • Page 8 Alarms The unit runs a number of checks during the start-up cycle and during normal operation. The possible alarms and respective solutions are shown in the following table. Alarm Description Action - For 24 Vdc, switch the device off and move the AC/DC jumpers to DC.

  • Page 9: Description Of Operation

    Indicates that a valve in short circuit has been excluded from the cycle. The signaling of the code E14 alternates with the indication of the interested output is shown as Uxx where xx is the Switch the device off and back on after number of the output.

  • Page 10: Connection Diagram

    Connection Diagram...

  • Page 11: Fuse Table

    Contacts And Relay Terminal Block J2 Enable contact input consensus 14.15 terminals. Is used to activate the control unit remotely, it can be turned on and off remotely. The unit is supplied with a jumper on the two terminals 14:15, without it will not turn Fan contact 12.13 input terminals.
  • Page 12 Jumper Configuration Power Input 115 / 230 VAC 115 VAC 230 VAC Jumper Configuration Output 115 VAC 230 VAC 24 VAC 24 VDC...
  • Page 13 Installation – Casing Dimensions 4 - 8 Outputs Weight 1.8 Kg...
  • Page 14 Installation – Casing Dimensions 12 - 16 Outputs Weight 2.1 Kg...

  • Page 15: Maintenance

    Maintenance The only parts which may be replaced are fuses. All other operations must be carried out by the manufacturer. Scrapping Dispose of properly after use. Dispose of the product according to laws in force for electronic equipment. This device is for use in a dust collection system and is therefore part of a fixed installation.

  • Page 16: Problem Solution

    Problem Solution Fault Possible Cause Solution Check the protection fuse on the power voltage. Check that the power The display does not light Burnt fuse. voltage is present and compliant with that required for the device (terminals 1, 2 and 3). Check that the unit and solenoid vale output voltage The outputs are not...

  • Page 17: Declaration Of Conformity Of The Manufacturer

    Declaration Of Conformity Of The Manufacturer The Manufacturer: TURBO SRL The Manufacturer's Address: Via Po 33/35 20811 Cesano Maderno (MB), Italy Declares That Product Name: Sequencer E1T Models: E1T 4 - 16 Product Options: Complies with the following directives: Electromagnetic Compatibility Directive 2014/30/EU, meeting EU harmonised standards EN61000-6-2:2005 class B of Standard EN61000-6-4:2001.

This manual is also suitable for:

E1t 4E1t 16E1t series

Table of Contents