Advertisement
Quick guide
THANK YOU FOR BUYING A WHIRLPOOL PRODUCT.
TROUBLESHOOTING
In order to receive a more complete assistance,
please register your product on
Before contacting the Service Centre, refer to the table below. Often the malfunctions are minor and can be solved in few minutes
www.whirlpool.eu/register
Malfunction
Possible cause
The plug is not inserted into the socket.
The tumble
The plug is faulty.
dryer does not
turn on.
A power failure occurred.
The door is open.
A time delay for the cycle start was set.
The tumble
The button Start/Pause was not pressed to start
dryer does not
the program.
start
The function Key Lock was enabled (in case of
machines equipped with this option).
An appropriate maintenance was not carried
out.
The programme, the time and/or the drying
level set are not suitable for the type and the
The drying
amount of load inserted into the dryer.
times are very
long
The garments are too wet.
The dryer may be overloaded.
The programme
A power failure occurred might have
did not end.
Lights on or fl ashing
Water tank
The water tank is full.
Door fi lter
Failure of the air fl ow necessary for machine
and/or bottom
operation.
fi lter*
Bottom fi lter*
The bottom fi lter requires cleaning.
DEMO
The dryer is in DEMO mode. The DEMO
The cycle lasts
indicator is on.
few minutes.
The presence
of wrench
The machine sensors detected a failure.
symbol signals a
malfunction.
180'
120'
90'
60'
30'
*Note: some models are self-cleaning and not equipped with bottom fi lter. Please refer to the section Care & Maintenance.
You can download the Safety Instructions, User Manual, Product Fiche and Energy data by:
• Visiting our website -
• Using QR Code
• Alternatively, contact our After-sales Service (See phone number in the warranty booklet). When
contacting our After-sales Service, please state the codes provided on your product's identifi cation plate.
occurred.
The presence of wrench symbol signals a malfunction. Carry out the operations described.
Switch the dryer off and unplug it. Open the door immediately and pull landry out, to allow
the heat to dissipate. Wait for about one hour. Reconnect the dryer to the power supply, load
the laundry and restart the drying cycle.
9h
If the problem still occurs, contact the After-Sales Service Centre and communicate the
6h
number and the position of the fl ashing LEDs, starting from the bottom and the left column.
3h
e.g.:
First, left column, LEDs No. 1 and 3 on.
1h
Central column, LED No. 1 on.
docs.whirlpool.eu
Before using the appliance carefully read the Safety Instructions.
Before using the appliance carefully read the Safety Instructions.
Solution
Insert the plug into the socket.
Try to plug another appliance in the same socket. Do not use
connecting electrical devices to the socket, as adapters or extensions
Await the reactivation of the power supply.
Close the door.
For machines equipped with this function: await the end of the delay
set or switch the machine off to reset it. Refer to the section Options.
Press the button Start/Pause.
Refer to the option section and, if the Key Lock is present, disable it.
Switching the machine off is not enough to disable this option.
Refer to the section Care & Maintenance and perform the operations
described.
Refer to the section programmes and options to fi nd the programme
and the options most suitable for the type of load.
Carry out a washing cycle with higher spin speed to remove as much
water as possible.
Refer to the programme section to check the max. load for each
programme.
In case of power failure, it is necessary to press the button Start/Pause
to restart the cycle.
Emtpy the water tank. Refer to the section Care & Maintenance.
Clean the door fi lter and the bottom one and check whether air
intake is free. Carrying out these operations improperly may cause
damages.
Clean the bottom fi lter. Refer to section Care & Maintanence.
Disable the DEMO mode. The following actions must be carried out
in sequence, without breaks. Switch the machine on and then switch
it off again. Press the Start/Pause button until the buzzer is heard.
Switch the machine on again. The "DEMO" indicator fl ashes and then
turns off .
Switch the dryer off and unplug it. Open the door immediately and
pull laundry out, to allow the heat to dissipate. Wait for about 15
minutes. Reconnect the dryer to the power supply, load the laundry
and restart the drying cycle. If the problem still occurs, contact
the After-Sales Service Centre and communicate the letters and
digits fl ashing on the display.
For instance: F3 and E2
EN
xxxx
xxxx
xxxxxxxxxxxx
xxxxxxxxxxxx
Advertisement
