Advertisement
Quick Links
Advertisement
Related Manuals for Monstertech STAND
Summary of Contents for Monstertech STAND
- Page 1 STAND Instruction Manual EN...
-
Page 2: General Information
STAND INSTRUCTION MANUAL 1 General information Congrats on your brand new MONSTERTECH Stand! This guide is meant to help you assemble your Stand as smoothly as possible. If you still have questions about the assembly process, please contact info@monstertech.de or support@ monstertechusa.com. - Page 3 STAND INSTRUCTION MANUAL 1.1.2 Inserting T-Nut into Profile There are two ways to insert the M8 T-Nuts into the respective profile groove; refer to Figure 1 and 2 respectively. Figure 1: Slide in from side Figure 2: Rotate in from top...
- Page 4 STAND INSTRUCTION MANUAL 1.1.3 Universal Fastener Assembly The universal fastener assembly can be prepared the following way, so long as the T-Nut can be slid in from the side. One Universal Fastener Assembly is made up from one (1) M8x30 Hex Screw, one (1) T-Nut, and one (1) Universal Fastener.
- Page 5 STAND INSTRUCTION MANUAL 1.1.4 Angle Bracket Stud Removal Sometimes it might be necessary to break off the studs from angle brackets (if those are part of the product). This is best achieved by: 1. Inserting a flat-head screwdriver between the stud and the bracket, and then...
- Page 6 For some assemblies the use of angle brackets is required. These are prepared by using two (2) M8x18 hex screws, two (2) washers, and two T-Nuts. Figure 5: Angle bracket assembly 1.1.6 Adjustment of Profile Feet The profile feet are installed on the MTX Base Stand, MTX Stand-Alone TV or Stand. Figure 6: Profile feet...
- Page 7 STAND INSTRUCTION MANUAL 2 Overview 2.1 Completed Stand Stand - Overview Figure 8: Complete Stand Use the above image as reference for the following Stand assem- bly instructions.
- Page 8 STAND INSTRUCTION MANUAL Figure 9: Stand assembly - step 1 Figure 10: Stand assembly - step 2...
- Page 9 STAND INSTRUCTION MANUAL Figure 11: Stand assembly - step 3 Figure 12: Stand assembly - step 4...
- Page 10 STAND INSTRUCTION MANUAL Figure 13: Stand assembly - step 5 Figure 14: Stand assembly - step 6...
- Page 11 STAND INSTRUCTION MANUAL Figure 15: Stand assembly - step 7 Figure 16: Stand assembly - step 8...
- Page 12 STAND INSTRUCTION MANUAL Figure 17: Stand assembly - step 9 3.10 Figure 18: Stand assembly - step 10...
- Page 13 STAND INSTRUCTION MANUAL 3.11 Figure 19: Stand assembly - step 11 Your Completed MONSTERTECH Stand Figure 20: Stand assembly - step 12...
- Page 14 STAND INSTRUCTION MANUAL 4 Pedal Mount (optional) Figure 25: Pedal mount...
- Page 15 STAND INSTRUCTION MANUAL Figure 26: Pedal mount assembly - step 1 Figure 27: Pedal mount assembly - step 2...
- Page 16 STAND INSTRUCTION MANUAL Figure 28: Pedal mount assembly - step 3 Figure 29: Pedal mount assembly - step 4...
- Page 17 STAND INSTRUCTION MANUAL Figure 30: Pedal mount assembly - step 5 Figure 31: Pedal mount assembly - step 6...
- Page 18 STAND INSTRUCTION MANUAL Figure 32: Pedal mount assembly - step 5 Figure 33: Pedal mount assembly - step 6...
- Page 19 STAND INSTRUCTION MANUAL Figure 34: Pedal mount assembly - step 7 Your Completed Stand with Pedal Mount Congratulations! You’re all done with your MTX Stand!
- Page 20 Das Rennsitzgestell ist zur Verwendung in Kombination mit einem Autositz und nur zur Verwendung im Innenbereich ausgelegt. Wir übernehmen keine Haftung für zweckentfremdete Benutzung. Bei Fragen zur Sicherheit oder Aufbau des Rennsitzgestells, wenden Sie sich an info@monstertech.de oder besuchen unsere Website unter www.monstertech.de.
-
Page 21: Warning Notices
Only suitable for children over 12 years and adults. All MONSTERTECH products are handmade and quality checked. The racing Stand is only designed for inside usage in combination with a car seat. We exclude liability if the product is used for purposes other than intended.
Need help?
Do you have a question about the STAND and is the answer not in the manual?
Questions and answers