Related Manuals for Chapman TF350
Summary of Contents for Chapman TF350
- Page 1 TF Series Trailed Feeder (All Models) Original Instructions Chapman Machinery Ltd, Hele Barton, Week St. Mary, Holsworthy, Devon EX22 6XR Tel: 01288 308149 Email: sales@chapman.co.uk...
-
Page 2: Table Of Contents
4 Button Model (FROM October 2015) ..................21 Operating Limits & Recommendations ..................23 Forward Speed ..........................23 Storage ............................23 Troubleshooting ..........................24 Warranty ............................25 The Chapman Warranty ......................25 Warranty Conditions........................25 Transfer of Warranty ........................26 Page 2... -
Page 3: Introduction
Introduction By purchasing a Chapman Machinery Ltd TF Series Trailed Feeder you have purchased a product de- signed to give a long and trouble free service life. A variety of options are available from the factory, and many of these are also suitable for retro-fitment if your requirements change, or you purchase this machine used, and wish to use a different set-up. -
Page 4: Hse Information
HSE Information HSE information sheet Safe use of all-terrain vehicles (ATVs) in agriculture and forestry Agriculture Information Sheet No 33 Introduction Route planning and stability This information sheet gives advice on the safe use of Most accidents with these machines have occurred ATVs. - Page 5 Protective clothing Use a gauge that is designed for measuring and displaying low pressures – usually supplied with More than half of all ATV riders have been thrown off at the ATV; some time. As these machines are not fitted with either ●...
- Page 6 ● Never put your foot onto the ground to Using sprayers stabilise an ATV when riding, but shift your ● Pesticides should be used in accordance with the weight across the ATV away from the imbalance. Code of Practice for using plant protection Always read the owner’s manual.
- Page 7 ● ● Lap straps should not be fitted. They prevent Where there is a risk of the machine rolling over, active riding and would be potentially lethal PUWER requires an employer to fit some device without a full cab or roll cage. to protect employees (the self-employed have the same duty to themselves).
-
Page 8: Important Safety Information
Important Safety Information Always read this manual before fitting or operating the machine – whenever any doubt exists contact your dealer or the Chapman Machinery Service Department for advice and assistance. Use only Chapman Genuine Service Parts on Chapman Machinery and Machines... -
Page 9: Transportation Safety
- Never wear loose clothing which could get caught in rotating equipment - Never carry passengers on the towing vehicle - Do not stand near the machine when operating - Damaged or missing safety decals must be replaced immediately Transportation Safety - When transporting, especially over rough ground, reduce speed to prevent damage to machine. -
Page 10: Description
The rotor and wiring mechanism are all IP67 rated, to ensure trouble-free usage in even the toughest winter conditions. The TF350 has approximately 350kg carrying capacity (feed material dependant), a galvanised metal hopper and PVC cover. Standard wheels are 22x11x8” flotation, with optional heavy duty 24x12x12”... -
Page 11: Optional Equipment
- Traction Tyres - Extension Sides - Livestock Fender Bar - Twin Axle - Hard Top Bale Rack - Road legal kit - Additional Control Box Contact your distributor or Chapman Machinery for more information on optional equipment. Page 11... -
Page 12: Implement Decals
Implement Decals If your implement does not contain all of the decals shown below, please contact Chapman Engineering for replacement decals before use. Note: All decals must be present and visible. It is imperative that these are replaced if damaged to prevent potential harm to users. -
Page 13: Attachment
Attachment Before Attaching the Machine Before attachment, ALWAYS ensure the following: - All safety guards & decals are in good working order and correctly fitted - Lubrication points have been lubricated as per scheduled maintenance period - The tyres are free of damage and inflated to the correct pressure - Electrical connections are free of dirt and moisture Attaching the Machine NOTE: This machine is designed to attach to the towing vehicle through a 50mm diameter ball hitch. -
Page 14: Drop Size Adjustment & Calibration
Drop Size Adjustment & Calibration Initially set the Feed adjustment plate to setting 4, as indicated by the arrow on the drop adjustment plate. To adjust, loosen BOTH hand wheels, and slide the unit forwards or backwards to the desired value. Tighten securely. -
Page 15: Spring Change / Replacement
Spring Change / Replacement If you are using the TF350 for a molasses based feed, cobs or rolls. You will need to change the spring which is used to open/close the shutter. 1. REMOVE THE GUARD WHICH IS LOCATED UNDER THE DRAW BAR USING A 17MM SOCKET 2. - Page 16 3. REMOVE THE SPRING BY UNHOOKING IT FROM BOTH END 4. REPLACE THIS WITH THE STRONGER SPRING. Page 16...
-
Page 17: Sensor Change / Adjustment
Sensor Change / Adjustment If your control box is showing an F1 error and not counting correctly, you may have a problem with the connectors and/or the sensor may need adjustment. First, check the plug and socket connection between the control box and the feeder – THIS IS THE MOST COMMON CAUSE OF PROBLEMS! If required check continuity with a multi-meter. - Page 18 plate. TAKE NOTE OF THE NUMBER OF WASHERS AS THESE NEED TO BE RE-FITTED IN THE SAME ORDER TO ENSURE THE SLIDE MOVES SMOOTHLY. 3. In the Picture below you can see the sensor (with the wire) and the magnet (fitted to the disc) are facing each other with approximately 2mm gap between them.
- Page 19 Once this has been checked and all dirt removed, your problem should be resolved. If the problem persists, please contact us 01288 308 149 or email us on sales@chapman.co.uk we will be more than happy to help. Page 19...
-
Page 20: Control Box
Control Box 2 Button Model (UNTIL October 2015) The TF Series control box has a two-button operation, and a three-digit display, capable of counting up to 999 drops. The LH button switches the unit on, and a subsequent press of the LH button will start operation of the unit. A further single press will pause operation. -
Page 21: Button Model (From October 2015)
3. To pause the unit, press LH switch. To switch the unit off, press RH switch. 4 Button Model (FROM October 2015) The 4-button model has two modes of operation; - Count Mode: Unit counts up from 0 e.g. 1,2,3,4,5 indefinitely, until the count is paused or the unit switched off. - Page 22 To exit this fault condition once the problem has been identified turn the unit off. The TF350 electronic system is designed such that a fault can be diagnosed and remedied on site rela- tively easily; the motor and rotation sensor are separate components which can be replaced individu- ally should a fault occur, please contact your distributor or original equipment provider for assistance and parts should they be required.
-
Page 23: Operating Limits & Recommendations
Operating Limits & Recommendations Ensure that the operator is suitably qualified to use a machine of this nature and that they have fully read and understood this manual - they should be aware of all safety aspects relating to the safe use of the machine. It is advisable that all ‘first time’... -
Page 24: Troubleshooting
Motor does not operate even Poor connection between control box Check plug is clean and moisture though control box is on and TF350 free Shortage in wiring (may be indi- Check wiring for damage acted by unit losing power when run... -
Page 25: Warranty
This warranty does not affect your statutory rights, but merely adds to them. Should you have a problem within 24 months from the date of sale please contact your original dealer, or Chapman Machinery’s Service Department. -
Page 26: Transfer Of Warranty
Transfer of Warranty The Chapman warranty be transferred to a subsequent owner of the machinery (for use within the UK only) for the balance of the warranty period subject to all of the stated warranty conditions and provided that the Change of Owner form is completed and sent to Chapman Machinery within 14 days of change of owner- ship. - Page 27 Hele Barton Week St. Mary Holsworthy Devon EX22 6XR The Products Covered by this Declaration Product: TF350 Trailed Livestock Feeder & Options (Off-Highway) Standards and Regulations used: Machinery Directive 2006/42/EC Place of Issue: United Kingdom Name of Representative: James Chapman...