Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Vulcan-Hart VCD Series
Summary of Contents for Vulcan-Hart VCD Series
- Page 1 INSTALLATION & OPERATION MANUAL VCD & VCW SERIES CHIP WARMERS MODELS: VCD22* ML-138037 VCD44 ML-138069 VCW26 VCW46 *Formerly VCD5 VULCAN 3600 NORTH POINT BLVD. DIVISION OF ITW FOOD EQUIPMENT GROUP, LLC BALTIMORE, MD 21222 www.vulcanequipment.com © F-38053 (08-14) Vulcan 2014 All Rights Reserved...
-
Page 2: Important For Your Safety
VCW & VCD SERIES CHIP WARMER F-38053 (08-14) IMPORTANT FOR YOUR SAFETY THIS MANUAL HAS BEEN PREPARED FOR PERSONNEL QUALIFIED TO INSTALL ELECTRICAL EQUIPMENT, WHO SHOULD PERFORM THE INITIAL FIELD START- UP AND ADJUSTMENTS OF THE EQUIPMENT COVERED BY THIS MANUAL. -
Page 3: Table Of Contents
VCW & VCD SERIES CHIP WARMER F-38053 (08-14) TABLE OF CONTENTS IMPORTANT FOR YOUR SAFETY ........1 GENERAL . -
Page 4: General
VCW & VCD SERIES CHIP WARMER F-38053 (08-14) GENERAL INTRODUCTION Vulcan Chip Warmers are produced with As with any piece of food service quality workmanship material. equipment, this Chip Warmer requires a Proper installation, usage, minimum of care and maintenance. -
Page 5: Installation Specific To Models Vcd22 & Vcd44
VCW & VCD SERIES CHIP WARMER F-38053 (08-14) INSTALLATION SPECIFIC TO MODELS VCD22 & VCD44 ACCESS PANEL POSITIONING: SCOOP HOLDER INSTALLATION: Ensure that top Baffle notches The Chip Scoop Holder will secure up to are over carriage bolts. a 6“ wide scoop. -
Page 6: Electrical Requirements
VCW & VCD SERIES CHIP WARMER F-38053 (08-14) ELECTRICAL REQUIREMENTS warmers ELECTRICAL CODES & STANDARDS: equipped with a three-prong plug. It The warmer must be installed in is imperative that this plug must be accordance with: connected into a properly grounded three-prong receptacle. -
Page 7: Operation Instructions
VCW & VCD SERIES CHIP WARMER F-38053 (08-14) OPERATION OPERATION INSTRUCTIONS (Models VCD22 & VCD44) blower fan circulates heated air The Warmer and its through the perforated removable parts are hot. Be very careful when chip tray located at the bottom of... -
Page 8: Operation Instructions
VCW & VCD SERIES CHIP WARMER F-38053 (08-14) OPERATION INSTRUCTIONS (Models VCW26 & VCW46) The Chip Warmer should be thoroughly Adjust knob desired cleaned before initial use. temperature setting. Once a desired temperature setting is determined, the knob can be left in this position until a The Warmer and its temperature adjustment is needed. -
Page 9: Cleaning Instructions
VCW & VCD SERIES CHIP WARMER F-38053 (08-14) CLEANING INSTRUCTIONS (Models VCW26 & VCW46) 4. Remove interior baffle at the The Warmer and its bottom of the unit. A handle is parts are hot. Be very careful when located toward the back of the operating, cleaning, or servicing the baffle. -
Page 10: Stainless Steel Care
VCW & VCD SERIES CHIP WARMER F-38053 (08-14) EXTERIOR CLEANING: STAINLESS STEEL CARE Special stainless steel polishing cleaners can preserve and restore the CLEANING: protective film on the exterior of the unit. Stainless Steel contains 70 – 80% iron, which will rust if not properly maintained. -
Page 11: Lockout / Tagout Procedure
VCW & VCD SERIES CHIP WARMER F-38053 (08-14) LOCKOUT / TAGOUT PROCEDURE Always perform the LOCKOUT / TAGOUT PROCEDURE of your facility before removing any sheet metal panels or attempting to service this equipment. The Lockout / Tagout Procedure is used to protect personnel working on an electrical appliance. -
Page 12: Troubleshooting
VCW & VCD SERIES CHIP WARMER F-38053 (08-14) TROUBLESHOOTING SYMPTOM POSSIBLE CAUSE REMEDY Chip Warmer not Plug chip warmer into correct plugged into power power source as indicated on source. serial data plate. Lighted power switch not in ON position. VCW26 Chip Warmer not &... - Page 13 VCW & VCD SERIES CHIP WARMER F-38053 (08-14)
- Page 14 VCW & VCD SERIES CHIP WARMER F-38053 (08-14)
-
Page 15: Vcw & Vcd Series Chip Warmer F-38053 (08
VCW & VCD SERIES CHIP WARMER F-38053 (08-14)