Choosing A Location; Electrical Safety - Jacuzzi J-300 Series Installation Manual And Use & Maintenance

Be very careful when getting in an out of the spa. All of the
surfaces are slippery when wet.
The spa is not intended for use in public places; always check
for any restrictions and/or regulations concerning the installa-
tion and use of the apparatus in the area chosen.

Choosing A Location

Location for the Optional ProLink™ Remote Monitoring
System
IMPORTANT! Choose an installation site with the front control
panel side pointing towards your home's Wi-Fi router.
CAUTION: You must make sure that the spa control panel side
has a clear unobstructed line-of-site of the home Wi-Fi router.
This action ensures maximum signal strength between the spa
and your home's Wi-Fi router.
Verify your home router's Wi-Fi strength at the proposed spa lo-
cation. Front control panel side of spa must point towards your
home's Wi-Fi router in your home as illustrated.
Stand near the proposed front control panel side of the spa with
your cell phone, then login to the internet using your home Wi-
Fi router signal (not 3G or 4G) and verify results as follows:
If the home Wi-Fi router signal is strong (3-4 bars) and Internet
access is stable, the proposed installation site is a good choice.
If the home router's Wi-Fi signal is weak and Internet access is
slow or produces an error, the proposed installation site is not
a good choice.
It may be necessary to choose another spa installation site.
Relocate your home Wi-Fi router closer to the spa.
Install a "repeater" device in the room closest to the spa to boost
the home's router Wi-Fi signal at the proposed spa installation site.
Home WiFi
Router
Home WI-FI
Router

Electrical safety

The MaxiJacuzzi® are safe products, manufactured in complian-
ce with standards EN 60335-1, EN 60335-2-60, EN 12764 and
tested during production to ensure user safety.
Installation must be performed by qualified personnel who
ensure compliance with current national regulations and who
are also authorized to issue a certificate of compliance with pro-
per installation procedures.
It is the responsibility of the installer to select mate-
rials based on their intended use, to carry out work
properly, to check the condition of the system that
the unit will be connected to and that it ensures sa-
fety of use also concerning maintenance work and
the possibility to examine the system.
The MaxiJacuzzi® are class "I" appliances and therefore they
must be permanently connected, without any intermediate
connections, to the electrical system and to the protection sy-
stem (earth system).
The electrical system of the building must be pro-
vided with a 0.03A differential switch and with an
efficient protection (earth) circuit. Check for proper
operation of the differential switch by pressing the
TEST button, which should trip.
Parts incorporating electrical components, except
remote control devices, must be located or fixed so
that they cannot fall into the spa.
Live components and equipment must be out of re-
ach of individuals in the spa.
For connection to the electrical mains, it is necessary to in-
stall an omnipolar cut-off switch as per the values indicated in
the chapter "Electrical characteristics., which is to be located in
an area which is compliant with safety instructions and which
cannot be reached by the users who are using the MaxiJacuzzi®.
It is mandatory to comply with this instruction. Any other pro-
cedure is prohibited.
The installation of electrical devices and equipment (sockets,
switches, etc.) near the MaxiJacuzzi® must be in compliance
with legal standards and regulations in the country where the
MaxiJacuzzi® is installed.
The disconnection devices must be installed in the power
supply network according to the installation instructions.
For the equipotential connection as required by specific na-
tional standards, the installer must use the terminal provided
(standard EN 60335.2.60) in the electrical box, and marked with
the symbol . In particular, an equipotential condition must be
established for all metallic masses surrounding the spa, for
example water and gas pipes, metallic platforms, and so on.
Refer to the pre-installation information sheet for in-
structions and electrical input of the various models.
25