Hour Meter; Light Switch; Key Switch - Toro Workman HDX-D 07385 Original Instructions Manual

Hydraulic-Lift Lock
The hydraulic-lift lock secures the lift lever, so that the
hydraulic cylinders do not operate when the machine
is not equipped with a bed
lift lever in the O position when using the hydraulics
N
for attachments.
High-Low Range Shifter
The high-low range shifter adds 3 additional speeds
for precise speed control
•
You must stop the machine completely before
shifting between the H
•
Shift on level ground only.
•
Press the clutch pedal fully.
•
Move the lever fully forward for H
rearward for L .
OW
H range—For higher speed driving on level, dry
IGH
surfaces with light loads.
L range—For low-speed driving. Use this
OW
range when greater than normal power or control
is necessary. For example, steep grades, difficult
terrain, heavy loads, slow speed but high-engine
speed (spraying).
Important:
There is a location between H
L in which the transaxle is in neither range.
OW
Do not use this position as a N
because the machine could move unexpectedly if
the High-Low shifter is bumped and the gear-shift
lever is in gear.
4-Wheel Drive Button
4-Wheel Drive Models Only
To engage the 4-wheel drive manually, press and
hold the 4WD button (Figure
while the vehicle is in motion and the 4-wheel drive
engages.

Key Switch

Use the key switch (Figure
the engine.
The key switch has 3 positions: O
Rotate the key switch clockwise to the S
to engage the starter motor. Release the key switch
when the engine starts. The key switch moves
automatically to the O
N
To shut the engine off, rotate the key switch
counterclockwise to the O
(Figure 8). It also locks the
(Figure 8):
and L range.
IGH OW
and fully
IGH
IGH
position,
EUTRAL
8) on the center console
5) to start and shut off
, O , and S
FF N
position
TART
position.
position.
FF

Hour Meter

The hour meter indicates the total hours of machine
operation. The hour meter
whenever you rotate the key switch to the O
or if the engine is running.
Third-High-Lockout Switch
Move the third-high-lockout switch
S position and remove the key to prevent the use
LOW
of third gear when in the H
shuts off if the shift lever moves to third gear when
in H range.
IGH
Note:
The key is removable in either position.

Light Switch

Push the light switch
on or off.
Oil-Pressure-Warning Light
The oil-pressure-warning light
the engine-oil pressure drops below a safe level while
the engine is running.
Important:
and
the machine, shut off the engine, and check the
oil level. If the oil level is low, but adding oil does
not cause the light to go out when the engine
is started, shut off the engine immediately, and
contact your Authorized Toro Service Dealer for
assistance.
Check the operation of the warning lights as follows:
1. Engage the parking brake.
2. Turn the key switch to the O
but do not start the engine.
Note:
If the light does not function, either a bulb is
burned out or there is a malfunction in the
system which must be repaired.
Note:
1 to 2 minutes for the light to come on.
Glow-Plug Indicator Light
.
TART
The glow-plug indicator light
when the glow plugs are activated.
Important:
on for an additional 15 seconds when the switch
returns to the S
16
(Figure 5) starts to function
(Figure
range. The engine
IGH
(Figure 5) to toggle the headlights
(Figure
If the light flickers or remains on, stop
/P
N
The oil-pressure light should glow red.
If engine was just turned off, it may take
(Figure
The glow-plug indicator light turns
position.
TART
position
N
5) to the
5) illuminates if
position,
REHEAT
5) illuminates red