Advertisement
Keep children and unauthorised persons away from the work area.
9
When not in use, store the panel dryer carefully in a safe, dry, childproof location.
9
2. INTRODUCTION
n
Three 1000W high output short wave lamps in three individually switched cassettes. Lamps emit short wave infrared heat ideal for optimizing drying
of water based paints. This flexible system allows each cassette to be adjusted and locked in position around the contours of the vehicle, ensuring
maximum area coverage. Height adjustment is made using the locking gas strut, offering near weightless movement of the cassette support arm.
Supplied with 5mtr power cable.
3. SPECIFICATION
Model No: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .IR3000.V2
Number of Elements: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Element Power: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 x 1000W
Reflector Size: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 490 x 140mm
Supply: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230V
4. ASSEMBLY
fig.1
4.1.
Assemble unit (fig.1).
4.1.1.
Unpack U shape base (A) place on floor and lock rear wheels.
4.1.2.
Unpack main upright (B) remove nuts and washers from the base of the upright. Caution! DO NOT remove safety strap.
4.1.3.
Place protruding bolts on upright into pre-drilled holes in base. Hold in place lightly with washers and nuts. Cut and remove safety strap,
tighten nuts and secure being careful not to touch the gas strut handle.
4.1.4.
Raise support arm (D) carefully using handle (C) on gas strut until the arm is horizontal to main upright. Ensure support arm is being
held whilst being raised.
4.2.
To Assemble the Cassette Module:
Please note: before proceeding as below, remove the T-handle from the centre strap and discard the M8 nut.
4.2.1.
Set out the cassettes so that all the cables are on the same side and that the centre cassette has the central holes in for the mounting
arm.
4.2.2.
Fit the cassette strap assemblies with the 12 bolts and washers to the cassettes (fig.2).
4.2.3.
Fit the Mounting Arm to central cassette using the T-Knob, flat washer and star washer. Make sure that the star washer fits between
the cassette strap assembly and the mounting arm (fig.3).The assembled cassette head should be as shown in fig.4
fig.2
4.2.4.
Once the cassette assembly is complete, place the star washer onto protruding cassette bolt (G), then fit bolt into hole on the swivel head
(H). Then place the star washer, plain washer and secure with the handle.
4.2.5.
Plug cassette cables into socket (J).
4.2.6.
The unit may now be operated by pushing the handle (C) on the lockable gas strut while pulling down or pushing up the support arm (D)
to the desired position.
4.2.7.
IR3000 is not supplied with fitted a plug. There are three options:
• Blue Industrial IP44 2pin + Earth plug
• Have the unit hard-wired.
Important: If in any doubt, contact a competent electrician.
© Jack Sealey Limited
fig.3
Original Language Version
fig.4
IR3000.V2| Issue 1 06/09/16
Advertisement
