Pre-Roll Time; File Backup Function - Sony MAV-555SS Operation Manual

When the P1 key was pressed
The signal supplied to the R1 port is output in the EE status
when the monitor output is an RP port playback signal, or
when PB/EE has been specified.
Audio volume and video process level at the meter panel
apply to the playback signal.
After pressing the P1 key, perform REMOTE setup of the
RP port. REMOTE mode

5-5-7 Pre-roll Time

When using this unit as the player during DMC editing,
the setting should be at least five seconds.
Also, with DMC editing, the insertion point may be
displaced by one frame.

5-5-8 File Backup Function

If the power to the MAV-555SS is accidentally cut while
you are editing a file, the "Backupxxxxx" file (where
xxxxx is the date, for example: 05.20-14:00) is
automatically created. Therefore, if this happens and the
edited file is deleted, you can continue editing using the
backup file. However, if the edited file is unloaded before
the power is cut, backup is not possible. Further, because
the cut point information is not saved along with the
backup file, you cannot perform cut jumps or trim cuts in
this file.
You can unload files from the MAVE-D555 and BKMA-
505.
For details about unloading files, refer to the MAVE-D555 and
BKMA-505 operation manuals.
5-5-9 Editing-Related Error
Messages
There are some unique editing function-related errors
which may occur in BVE mode that do not exist in other
modes. These error messages and their remedies are
described below.
[Cut Entry Full]
In BVE mode, cut information for the file being edited
is stored internally. Although this information cannot be
used in linear editing, it can be used as cut information
for nonlinear editing when the MAVE-F555 is
connected.
There is a limit on the number of cuts per file. The [Cut
Entry Full] error appears when this limit has been
reached, and indicates that the file in question cannot be
edited any further.
Remedy:
• When the above error is generated, follow the
instructions that are provided in the dialog box that
appears on the control panel. Doing so will clear the
cut information for that file, making further editing on
the file possible.
• This error can be avoided by performing certain
operations through the MAVE-F555. For details, refer
to the "Error Message List" in the appendix in the
MAVE-F555 operation manual.
[Edit Entry Full]
The internal area where cut information is stored limits
the number of files that can be stored. The [Cut Entry
Full] error appears when this limit has been reached, and
indicates that no more files can be created for editing.
Because an internal temporary file is created when
editing through the RP port, editing is no longer possible
once this error has been generated.
Remedy:
• When the above error is generated, follow the
instructions that are provided in the dialog box that
appears on the control panel. Doing so will clear the
internal cut information area, making further file
creation and editing possible.
• This error can be avoided by performing certain
operations through the MAVE-F555. For details, refer
to the "Error Message List" in the appendix in the
MAVE-F555 operation manual.
[Rec Inhibit]
This error is generated if an attempt was made to record
or edit while the recording port or RP port was in the
"Rec Inhibit" state, or an attempt was made to record or
edit a file with file protection on.
Remedy:
Cancel "Rec Inhibit" or file protection in order to record
or edit.
[Material Entry Full]
The MAV-555SS material management information is
full; no files can be created.
Remedy:
Unneeded files are deleted.
[Nearly Rec Stop]
When editing or recording a collection file in BVE
mode, a four-minute area is allocated on the HDD; then,
as recording continues, when two minutes of this
allocated area is used up, enough area for two more
minutes is allocated. This operation repeats as recording
continues. This error occurs when the area for two
additional minutes cannot be allocated because the disk
is full. Once this error is generated, recording/editing
stops after two minutes.
Remedy:
• Recording/editing can continue further even after this
error is generated if you delete any unnecessary files
within two minutes of the moment when this error was
generated.
5-5 Basic Operations in BVE Mode
5-9 (E)