Table of Contents
Advertisement
Quick Links
www.waveshare.com
Open407V-C\Open207V-C Testing Guide
Open407V-C\Open207V-C Testing Guide
Contents
Preparation ............................................................................................................................................................................. 3
ADC+DMA ............................................................................................................................................................................... 3
CAN1 TO CAN2-Normal....................................................................................................................................................... 4
DAC .......................................................................................................................................................................................... 5
DCMI_OV7670 ........................................................................................................................................................................ 6
DCMI_OV9655 ........................................................................................................................................................................ 7
DS18B20 .................................................................................................................................................................................. 8
GPIO_Key_LED ..................................................................................................................................................................... 9
I2C ........................................................................................................................................................................................... 10
LCD-HY32D_FSMC ............................................................................................................................................................. 11
MCO_OUT ............................................................................................................................................................................. 12
Nand Flash_PCB0 ............................................................................................................................................................... 13
Nand Flash_SCB0 ............................................................................................................................................................... 14
RTC ......................................................................................................................................................................................... 15
SD_FatFS .............................................................................................................................................................................. 16
SDIO ....................................................................................................................................................................................... 17
SPI .......................................................................................................................................................................................... 18
Touch Panel.......................................................................................................................................................................... 19
UcosII2.91+UCGUI3.90A ................................................................................................................................................... 19
USARTx_pritf ....................................................................................................................................................................... 20
VS1003B MP3 Board .......................................................................................................................................................... 21
I2S ........................................................................................................................................................................................... 22
USB FS Example ................................................................................................................................................................. 24
1
Advertisement
Table of Contents
Related Manuals for Waveshare Open407V-C
Summary of Contents for Waveshare Open407V-C
-
Page 1: Table Of Contents
Open407V-C\Open207V-C Testing Guide Open407V-C\Open207V-C Testing Guide Contents Preparation ..................................... 3 ADC+DMA ....................................3 CAN1 TO CAN2-Normal............................... 4 DAC ......................................5 DCMI_OV7670 ..................................6 DCMI_OV9655 ..................................7 DS18B20 ....................................8 GPIO_Key_LED ..................................9 I2C ......................................10 LCD-HY32D_FSMC ................................11 MCO_OUT ..................................... 12 Nand Flash_PCB0 ................................ - Page 2 Open407V-C\Open207V-C Testing Guide USB HS Example ................................33 ETH ......................................37...
-
Page 3: Preparation
Open407V-C\Open207V-C Testing Guide Preparation Basic settings of the test · Programming Interface: SWD · Serial port settings: Select a proper COM port, configure as follows: Baud rate:115200; Data bits:8; Stop bits:1; Parity bits: None; ... -
Page 4: Can1 To Can2-Normal
Open407V-C\Open207V-C Testing Guide Operation and Result Launch the serial debugging assistant, and configure it as described in chapter "Preparation". Info/message will be displayed on the serial debugging assistant as adjusting the resistor on the module. CAN1 TO CAN2-Normal Overview... -
Page 5: Dac
Open407V-C\Open207V-C Testing Guide Operation and Result Launch the serial debugging assistant, and configure it as described in chapter "Preparation". Press the JOYSTICK and Check the results on the serial debugging assistant. Overview DAC output demo Hardware Connection · Connect the Analog Test Board to the board via SPI1 interface. -
Page 6: Dcmi_Ov7670
Open407V-C\Open207V-C Testing Guide As shown in the figure below: Operation and Result There will be a sound of triangular wave from the Analog Test Board. DCMI_OV7670 Overview OV7670 Digital camera data acquisition and display on the LCD Hardware Connection ·... -
Page 7: Dcmi_Ov9655
Open407V-C\Open207V-C Testing Guide · Connect the 3.2inch 320x240 Touch LCD (A) to the board via LCD interface As shown in the figure below: Operation and Result Images acquired from the camera will be displayed on the LCD. DCMI_OV9655 Overview... -
Page 8: Ds18B20
Open407V-C\Open207V-C Testing Guide · Connect the OV9655 Camera Board to the board via DCMI interface. · Connect the serial port converter to the board via UART3 interface. · Connect the 3.2inch 320x240 Touch LCD (A) to the board via LCD interface. -
Page 9: Gpio_Key_Led
Open407V-C\Open207V-C Testing Guide · Insert the DS18B20 to the ONE-WIRE Interface. · Connect the serial port converter to the board via UART3. As shown in the figure below: Operation and Result Launch the serial debugging assistant, and configure it as described in chapter "Preparation". -
Page 10: I2C
Open407V-C\Open207V-C Testing Guide Hardware Connection · Short the LED jumpers on the board. · Short the push button jumper, joystick jumper on the board. As shown in the figure below: Operation and Result Push the button or joystick; the LED status will keep changing accordingly. -
Page 11: Lcd-Hy32D_Fsmc
Open407V-C\Open207V-C Testing Guide Operation and Result Launch the serial debugging assistant, and configure it as described in chapter "Preparation". Info/message will be displayed on the serial debugging assistant. LCD-HY32D_FSMC Overview LCD display demo Hardware Connection... -
Page 12: Mco_Out
Open407V-C\Open207V-C Testing Guide · Connect the 3.2inch 320x240 Touch LCD (A) via LCD Interface to the board. As shown in the figure below: Operation and Result Information will be displayed on the LCD. MCO_OUT Overview Clock signal output demo... -
Page 13: Nand Flash_Pcb0
Open407V-C\Open207V-C Testing Guide Nand Flash_PCB0 Overview Nand Flash_PCB0 demo Hardware Connection · Connect the K9F1G08U0C NandFlash Board (K9F1G08U0C PCB0 onboard) to the board via 8BIT FSMC interface. · Connect the serial port converter to the board via UART3. As shown in the figure below: Operation and Result Launch the serial debugging assistant, and configure it as described in chapter "Preparation". -
Page 14: Nand Flash_Scb0
Open407V-C\Open207V-C Testing Guide Nand Flash_SCB0 Overview Nand Flash_SCB0 demo Hardware Connection · Connect the NandFlash Board (A) (K9F1G08U0D SCB0 onboard) to the board via 8BIT FSMC interface. · Connect the serial port converter to the board via UART3. As shown in the figure below: Operation and Result Launch the serial debugging assistant, and configure it as described in chapter "Preparation". -
Page 15: Rtc
Open407V-C\Open207V-C Testing Guide Overview RTC demo Hardware Connection · Connect the serial port converter to the board via UART3. As shown in the figure below: Operation and Result Launch the serial debugging assistant, and configure it as described in chapter "Preparation". -
Page 16: Sd_Fatfs
Open407V-C\Open207V-C Testing Guide SD_FatFS Overview SDIO interface + FatFS demo Hardware Connection · Connect the Micro SD Storage Board (with SD card) to the board via SDIO interface. · Connect the serial port converter to the board via USART2 interface. -
Page 17: Sdio
Open407V-C\Open207V-C Testing Guide SDIO Overview SDIO interface demo Hardware Connection · Connect the Micro SD Storage Board (with SD card) to the board via SDIO interface. · Connect the serial port converter to the board via USART2 interface. As shown in the figure below: Operation and Result Launch the serial debugging assistant, and configure it as described in chapter "Preparation". -
Page 18: Spi
Open407V-C\Open207V-C Testing Guide Overview SPI Flash demo Hardware Connection · Connect the serial port converter to the board via UART3 interface. · Connect the AT45DBXX DataFlash Board to the board via SPIx interface. · Remove the jumper between PA5 and FLG on the core board, or else the SPI won't work. -
Page 19: Touch Panel
Open407V-C\Open207V-C Testing Guide Touch Panel Overview LCD touch screen demo Hardware Connection · Connect the 3.2inch 320x240 Touch LCD (A) to the board via LCD interface. As shown in the figure below: Operation and Result LCD touch screen function works, and allows writing and drawing on the LCD. -
Page 20: Usartx_Pritf
Open407V-C\Open207V-C Testing Guide UcosII2.91+UCGUI3.90A DEMO Hardware Connection · Connect the 3.2inch 320x240 Touch LCD (A) to the board via LCD Interface. As shown in the figure below: Operation and Result Launch the serial debugging assistant, and configure it as described in chapter "Preparation". -
Page 21: Vs1003B Mp3 Board
Open407V-C\Open207V-C Testing Guide · Connect the serial port converter to the board via UART3 Interface. As shown in the figure below: Operation and Result Launch the serial debugging assistant, and configure it as described in chapter "Preparation". Info/message will be displayed on the Serial debugging assistant. -
Page 22: I2S
Open407V-C\Open207V-C Testing Guide Operation and Result · Insert the headphone to the Line Out port. · Connect the PC audio port and the VS1003B MP3 Board Line In port by audio cable. · Play music on the PC side, then ·... - Page 23 Open407V-C\Open207V-C Testing Guide (1) MCU_FLASH Hardware Connection · Connect the UDA1380 Board to the board via I2S interface. As shown in the figure below: Operation and Result Put the headset to the HEADPHONE jack, then will hear the music stored in the MCU FLASH.
-
Page 24: Usb Fs Example
Open407V-C\Open207V-C Testing Guide Operation and Result · Put the audio file named "Audio.wav" on SD card root directory. · Put the headset to the HEADPHONE jack. · SD card audio file information displayed on the serial debugging assistant. ·... - Page 25 Open407V-C\Open207V-C Testing Guide · Connect the 3.2inch 320x240 Touch LCD (A) to the board via LCD interface. · Short the Joystick, LED jumpers. As shown in the figure below: (1) USB_Device_Examples--HID Hardware Connection Connect the PC and the Core board by USB Cable. As shown in the figure below:...
- Page 26 Open407V-C\Open207V-C Testing Guide Operation and Result Message/info will be displayed on the LCD, and JOYSTICK can be used for simulating the mouse and controlling movement of the computer and mouse. (2) USB_Device_Examples--MSC Hardware Connection · Connect the PC and the Core board by USB Cable.
- Page 27 Open407V-C\Open207V-C Testing Guide Operation and Result · Message/info will be displayed on the LCD and SD card hard disk will be founded in the PC. (3) USB_Device_Examples--VCP Hardware Connection · Connect the PC and the Core board by USB Cable. As shown in the figure below:...
- Page 28 Open407V-C\Open207V-C Testing Guide Operation and Result After install the driver, a USB VCP (Virtual Com Port) will be identified by the PC. As shown in the figure below: (4) USB_Host_Examples--MSC Hardware Connection · Connect the Core board and the USB Flash Drive by the USB OTG cable...
- Page 29 Open407V-C\Open207V-C Testing Guide As shown in the figure below: Operation and Result The serial debugging assistant will display the file list in the USB flash drive, the example code will place a TXT file into the USB flash drive, and then the serial debugging assistant will display the picture.bmp message.
- Page 30 Open407V-C\Open207V-C Testing Guide Hardware Connection · Connect the Core board and the USB mouse / keyboard by the USB OTG cable. As shown in the figure below: Operation and Result The mouse or keyboard will be detected: · When connecting a keyboard, the LCD will display the pressed key value.
- Page 31 Open407V-C\Open207V-C Testing Guide · When connecting a mouse, the LCD will display the mouse's current status. (6) USB_Host_Examples_Examples--DRD Hardware Connection Device mode: Connect the Micro SD Storage Board (with SD card) to the board SDIO via interface; then connect the board and PC via USB cable.
- Page 32 Open407V-C\Open207V-C Testing Guide Operation and Result Put the picture.bmp to the USB Flash Drive, and message will be displayed on the LCD · When programming DEVICE DEMO, SD card hard disk will be founded in the PC. · When programming HOST DEMO, press the joystick to read the picture.bmp in USB Flash Drive.
- Page 33 Open407V-C\Open207V-C Testing Guide USB HS Example Overview USB HS Demo Hardware Connection · Open the 3 jumpers PA5-FLG, PA3-PWROUT and PA9-VBUS for the following test. · Connect the 3.2inch 320x240 Touch LCD (A) to the board via LCD interface.
- Page 34 Open407V-C\Open207V-C Testing Guide · Connect the PC and USB3300 USB HS Board OTG receptacle by USB cable. As shown in the figure below: Operation and Result · Message/info will be displayed on the LCD, and JOYSTICK can be used for simulating the mouse and controlling movement of the computer and mouse.
- Page 35 Open407V-C\Open207V-C Testing Guide Operation and Result Message will be displayed on the LCD; SD card hard disk will be founded in the PC. (3) USB_Device_Examples--VCP Hardware Connection · Connect the PC and USB3300 USB HS Board OTG receptacle by USB cable. As shown in the figure below:...
- Page 36 Open407V-C\Open207V-C Testing Guide After installed the driver, a USB VCP (Virtual Com Port) exists on the PC. As shown in the figure below: (4) USB_Device_Examples--MSC Hardware Connection · Connect a USB flash drive to the USB3300 USB HS Board HOST receptacle. As shown in the figure below: Operation and Result Message/info will be displayed on the LCD, the example code will place a TXT file into the USB Flash Drive;...
- Page 37 Open407V-C\Open207V-C Testing Guide Operation and Result The mouse or keyboard will be detected: · When identified as USB keyboard, the LCD will display the information input from the keyboard. . When identified as USB mouse, the LCD will display the mouse current status.
- Page 38 Open407V-C\Open207V-C Testing Guide NETMASK_ADDR: 255.255.255.0 GW_ADDR: 192.168.1.1 Hardware Connection · Connect the DP83848 Ethernet Board to the board via ETH interface, then connect it to the PC through a straight-through Ethernet cable. As shown in the figure below: Operation and Result Enter 192.168.1.10 in the Internet Explorer URL bar and then there will be a demo page.
- Page 39 Open407V-C\Open207V-C Testing Guide...