Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
Advertisement
Table of Contents
Related Manuals for IRTrans USB
Summary of Contents for IRTrans USB
- Page 1 Hardware guide USB - RS232 - Mediacontroller - Translator Version 2013.02...
- Page 2 Hardware Guide USB - RS232 - Translator - Mediacontroller EG Declaration of Conformity The following produtcs IRTrans USB IRTrans RS232 IRTrans IR Busmodul IRTrans Translator / XL IRTrans Mediacontroller are confirmed to comply with DIN EN 55024: 1998 + A1: 2001 + A2: 2003.
-
Page 3: Table Of Contents
Contents 1. IRTrans USB ................4 1.1 Connections ..................4 1.2 Power supply ..................5 1.3 USB connection / installing drivers ........... 5 2. IRTrans Translator ..............7 2.1 Connections ..................7 2.2 Power supply ..................8 2.3 USB connection / installing drivers ........... 8 3. -
Page 4: Irtrans Usb
USB - RS232 - Translator - Mediacontroller 1. IRTrans USB The IRTrans USB is an infrared (IR) Transceiver with USB PC interface. It can be supplied with power by the USB connection as well as by an external power supply. -
Page 5: Power Supply
Before connecting the IRTrans to the PC the software has to be in- stalled. The IRTrans USB will be connected to the PC by an USB A to B type cable. After connecting the IRTrans driver installation will start automatically. - Page 6 The IRTrans USB will be assigned a device (e.g. /dev/tty/USB0). The device ID will vary according to your system configuration. Drivers for Mac OSX 10.4 or later are available on the IRTrans software CD or are downloadable from the website http://www.irtrans.de/en/.
-
Page 7: Irtrans Translator
USB - RS232 - Translator - Mediacontroller 2. IRTrans Translator The IRTrans Translator is based on an IRTrans USB. An integrated command database allows to receive, translate and send IR commands independently. Compared to the IRTrans USB the IRTrans Translator offers the following additio- nal features: ... -
Page 8: Power Supply
Before connecting the IRTrans to the PC the software has to be in- stalled. The IRTrans USB will be connected to the PC by an USB A to B type cable. After connecting the IRTrans driver installation will start automatically. - Page 9 The IRTrans USB will be assigned a device (e.g. /dev/tty/USB0). The device ID will vary according to your system configuration. Drivers for Mac OSX 10.4 or later are available on the IRTrans software CD or are downloadable from the website http://www.irtrans.de/en/.
-
Page 10: Irtrans Rs232
The IRTrans RS232 is powered through a 5.5/2.1mm hollow connector. The ex- ternal power supply should be capable of delivering 8-16V with approximately 100mA per IRTrans Module. The positive lead must be wired to the center termi- nal. ©2012 IRTrans GmbH... -
Page 11: Irtrans Mediacontroller
Hardware Guide USB - RS232 - Translator - Mediacontroller 3.3 RS 232 Schnittstelle The IRTrans RS232 uses a 6-pin modular jack for the serial sonnection. The cab- le must be wired like this: Signal Pin (PC - SubD9) Pin IRTrans 4. -
Page 12: Mini Din 8 Connector For External Accessories
Hardware Guide USB - RS232 - Translator - Mediacontroller 5. Mini DIN 8 connector for external accessories There is a Mini-DIN 8 connector to plug external accessories into the IRTrans. The following options are available: External IR transmitters ... -
Page 13: External High Power Transmitters
Hardware Guide USB - RS232 - Translator - Mediacontroller 5.1.2 external high power IR transmitters The external high power transmitters are equal to the built in IR LEDs. They are available in a high frequency version as well (455kHz). The high frequency trans- mitters can be recognised by clear LEDs. -
Page 14: Status Input
Do not exceed 5,0V on the state input! 5.3 IRTrans bus The IRTrans 2 wire bus is a serial bus that can be controlled by an IRTrans USB or RS232. IRTrans bus modules extend IR coverage to multiple rooms and can be addressed independently through the IRTrans USB / RS232. -
Page 15: Poweron Option
USB - RS232 - Translator - Mediacontroller 5.4 PowerOn relay IRTrans devices with the PowerOn option have an additional relay to switch on ATX PCs. The two pin connector of the power on cable has to be connected to the power on pins of your mainboard. The power on connector of the PC case can be connected in turn to the power on cable.
Need help?
Do you have a question about the USB and is the answer not in the manual?
Questions and answers