1. Manuals
  2. Brands
  3. IRTrans Manuals
  4. Electronic dictionary
  5. IRTrans USB
  6. User manual

IRTrans USB User Manual

Hide thumbs Also See for IRTrans USB:
Table of Contents

Advertisement

Quick Links

Download this manual
Enlarged version
Users Manual
For the following products
we hereby declare that they conform to the declarations regarding Electromagnetic
Compatibility as defined in
Users Manual IRTrans System © 2006-2008 IRTrans GmbH
2
Version 2.12
Users Manual IRTrans Version 2.12
EU Declaration of Conformity
IRTrans USB
IRTrans Serial
IRTrans IR Bus Module
IRTrans Translator
IRTrans Mediacotroller
IRTrans Ethernet / IRDB
IRTrans Ethernet PoE / IRDB
IRTrans LAN Controller
IRTrans LAN Controller XL
EN 55024: 1998 + A1: 2001 + A2: 2003

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the IRTrans USB and is the answer not in the manual?

Questions and answers

Related Manuals for IRTrans IRTrans USB

Summary of Contents for IRTrans IRTrans USB

  • Page 1 IRTrans LAN Controller XL we hereby declare that they conform to the declarations regarding Electromagnetic Compatibility as defined in EN 55024: 1998 + A1: 2001 + A2: 2003 Users Manual Users Manual IRTrans System © 2006-2008 IRTrans GmbH Version 2.12...

  • Page 2: Table Of Contents

    Informations regarding the Macintosh Software can be found in the Manual shipped with the Macintosh Software. Damage to the IRTrans, the computer system or even personal property might arise as a result of not following advices marked by that symbol.

  • Page 3: Irtrans - Quick Reference Guide

    Ob LINUX the script install.sh on the CD has to be started. By default The Ferrite Core shipped with the IRTrans should be attached to the the software will be installed in the folder /usr/local/irtrans. It can also...

  • Page 4: Usb Version

    RS232 cable. If an external power supply is used, only GND / RxD / TxD might destroy the IRTrans. This Pin can be used to power the IRTrans via the Standby Voltage of an are needed. Most PCs deliver enough power using the status lines of the RS232 port ATX Power supply.

  • Page 5: Connecting The Poweron Option

    If an external power supply is used, only GND / RxD / TxD are needed. 2.6. Building a multizone system The IRTrans System ist used to control larger homes, too. To do that up A power supply is needed for the IRTrans RS232 or Mediacontroller.

  • Page 6: Usb Driver Installation

    (irserver). Therefore this server has to run all the folder or just put the software CD into your CD-ROM drive. After time. Right now there are no clients which connect directly to the IRTrans connecting the transceiver you only need to point the operating system to hardware.

  • Page 7: Starting The Server Automatically

    On Windows Systems simply copy the correct irtranstray Startmenu -no_reconnect The server does not try to reconnect to the IRTrans device when the Item (in the Menu folder IRTrans) to the Autostart folder. If needed, the device was removed (USB devices only) Options used to start the server can be modified.

  • Page 8: Format Of The Irtrans Ir Database

    PC is only possible if the option “Use always RAW Codes” is activated in the setting of the IRTrans module. Of course this codes can be sent the same way as other commands. They are described by Pulse/Pause pairs in µs. Values of more In general there might be three different formats inside a .rem file:...

  • Page 9: Irtrans Gui Client

    Even commands that are not included in the simple Remote Control can [MOD]10,10 [SIZE]40,25[PANEL]TV [MOD]60,10 [SIZE]40,25[PANEL]CD be sent. In addition, all the parameters of all IRTrans units connected to [END] the serial bus can be configured. The GUI client uses the IRTrans Server [CD] Socket (21000) to connect to the server.
  • Page 10 Protocol. This is done by shortly pressing one of the Remote controls buttons. When learning a timing the Remote control should face the IRTrans directly, not reflected by For special purposes there are additional Learn modes: wall as that might affect the timings learned.
  • Page 11 All selections in this Page will be stored permanently in the EEPROM of the timings for different commands. If some commands can not be IRTrans. If more then one IRTrans Module is connected the correct one has to be learned with the recorded timing, this function allows learning them.
  • Page 12 On most Mainboards wakeup from Standby only works from S1 Standby. Using the IRTrans PowerOn Option is a lot more versatile. If you use the IRTrans in RAW mode this has to be a RAW command, too.

  • Page 13: The Ascii / Batch Client (Irclient)

    Switch on your Receiver and TV if you start the DVD player on the PC … In the Settings Dialog for the IRTrans Plug-in the Hostname of the Server The IRTrans Server is fully compatible with the LINUX VDR system. It is is entered.
  • Page 14 Users Manual IRTrans Version 2.12 Users Manual IRTrans Version 2.12 Now the commands can be learned with Girder. When the IRTrans Plug- in is selected in the Learn Combo box, the commands will be learned Now a name for the through the IRTrans Dialog and stored in the IRTrans IR Database.

  • Page 15: Irtrans And Homeseer

    Installation The IRTrans Plug-in (hspi_irtrans.ocx) located on the IRTrans Software CD or in the plugins folder of the IRTrans installation folder has to be copied into the Homeseer Installation Directory. If Homeseer is installed in the standard path this is done automatically by the IRTrans setup program.
  • Page 16 Commands. Model Numbers: IRTrans USB IRTrans RS232 The Commands are stored in the IRTrans Database as follows: IRTrans Translator The Remote is called _hs_<Remotename>; for example _hs_TV IRTrans Busmodule The command has the same name as the command in Homeseer...

Table of Contents