Page 1
ONLY AUTHORIZED PERSONS MAY WORK WITH THE MACHINE IMPROPER USE CAN CAUSE SERIOUS INJURIES! All maintenance and repair should be done by the manufacturer or under their supervision by an official distributor. Each TTMA should be delivered with 3 certificates to guarantee the right performance.
11.2 Other welding ........................14 Warranty ............................15 Document delivered by each TTMA ..................... 16 13.1 TTMA certificate, signed by the Verdegro Group ..............16 13.2 Overall and mounting certificate ..................17 CE certification ..........................18 Maintenance history ........................19...
(F) +31(0)76-5019404 (W) www.verdegro.com (E) info@verdegro.com Date release : _____________________ Machine number : _____________________ Cushion number : _____________________ Company stamp: Note: This document is only valid with an original company stamp of the producer. Manual TTMA-100K Page 3 of 19...
A Trailer truck mounted attenuator (TTMA) is an energy absorbing device attached to the rear of a truck or utility vehicle. A TTMA is designed to provide a controlled stop of a vehicle impacting the rear of the truck. TTMAs have been used since the mid- 1970's to reduce the severity of impacts between errant motorists and slow moving or stopped shadow vehicles used to protect highway maintenance workers.
Power hydraulic pump Equipped with thermo switch Hydraulic rotating cylinders Standard Hydraulic pump motor voltage Standard driving lights 24 V Battery Bank Safety fuse Cable from truck to TTMA DIN coupling 40 or 50 mm Manual TTMA-100K Page 7 of 19...
F. A truck equipped with a Verdegro TTMA shall have a forward skid distance of less than 10 m during an impact by either an 820 kg or 2000 kg vehicle traveling at a design speed of 100 kph.
Keep the operating instructions, always within easy reach of the machine, the operator's manual should ALWAYS be at or near the machine. 3. The operator of the TTMA must be at least 18 years old and experienced in serving Trailer truck mounted attenuators.
Page 10
Group or under their supervision by an official distributor. 20. If you leave the TTMA, put it somewhere where it does not preclude others. Keep the whole machine in transport position. Close all hatches well for unauthorized persons. Take your keys with you.
Verdegro or a distributor, and that a certificate is given. Also make sure the bumper of the truck is correctly installed. The TTMA is tested with a 40mm DIN coupling, so a 50mm will also be correct.
8 Inspection 8.1 Inspection table General inspection points (It they are in bad Every Weekly Monthly condition, use of the TTMA is forbidden) application Visual inspection of shafts,bolts and structural bearings Inspection LED display control (errors) / arrow configuration(s) Visual inspection loose machine parts...
Read for the maintenance of the TTMA the entire manual carefully!. If in doubt about the maintenance work it is better that it is carried out by the manufacturer. If not, than it must be done under supervision of the manufacturer, for example by an official distributor.
Crash Cushion: o Control of cracks and dents or cracks 11 Repairs (by manufacturer or official distributor) 11.1 Welding If parts of the TTMA are repaired with welding, it should be noted in the report under "Remarks’’ Welded points ...
12 Warranty Verdegro strives by various internal and external inspections and final inspections that the delivered TTMA system is free from error into operation. We provide the following warranty for any defects in materials or workmanship. The guarantee is effective up to 12 months from the date of delivery of the machine to the buyer.
13.2 Overall and mounting certificate Note: This certificate can be signed by the distributor and than will be the their responsibility Manual TTMA-100K Page 17 of 19...
14 CE certification CE Verklaring van conformiteit CE Declaration of conformity CE Konformitätserklärung Déclaration CE de conformité The Verdegro Group verklaart hiermee, dat het produkt hereby declare, that the product erklären hiermit, daß das Produkt déclare par la présente, que l’outil Is geproduceerd conform de normen en normatieve documenten overeenkomstig de bepalingen van de EG- richtlijnen 2006/42/EG en de NCHRP report 350-TL3.