1. Manuals
  2. Brands
  3. Kongskilde Manuals
  4. Tedders
  5. Z 455 H
  6. Operator's manual

Kongskilde Z 455 H Operator's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
ORIGINAL INSTRUCTIONS
- according to Directive 2006/42/EC, Annex I 1.7.4.1
OPERATOR'S MANUAL
Z 455 H
Z 555 H
Tedder
Part number 51514345
1
edition English
st
March 2019

Advertisement

Table of Contents
loading

Related Manuals for Kongskilde Z 455 H

Summary of Contents for Kongskilde Z 455 H

  • Page 1 ORIGINAL INSTRUCTIONS - according to Directive 2006/42/EC, Annex I 1.7.4.1 OPERATOR’S MANUAL Z 455 H Z 555 H Tedder Part number 51514345 edition English March 2019...

  • Page 2: Table Of Contents

    Contents 1 GENERAL INFORMATION Note to the owner................1-1 Intended use.
  • Page 3 Power Take-Off (PTO) shaft – Shorten ..........4-9 Working in the field .
  • Page 4 Every 50 hours Nuts and bolts ............... . . 7-14 Every year Hydraulic hoses .

  • Page 5: General Information

    Directives 2006/42/EC and 2014/30/EU. Always use genuine KONGSKILDE Service Parts or parts that match at least the same quality, reliability and func- tionality as the equivalent original Service Parts when you service and repair your implement and do not modify your implement without a written permission of the manufacturer.
  • Page 6 KONGSKILDE is not liable for any damage caused by the use of ''non-genuine” parts and accessories. Rely on your authorized dealer to supply you with genuine KONGSKILDE parts only. These parts are covered by our warranty and will give you the best performance.
  • Page 7 It is prohibited to carry out any modifications to the implement unless specifically authorized, in writing, by a KONGSKILDE representative. CLEANING YOUR IMPLEMENT When you use a high pressure washer, do not stand too close to the implement and avoid directing the jet at electronic components, electrical connections, breathers, seals, filler caps, and so on.

  • Page 8: Intended Use

    1 - GENERAL INFORMATION Intended use The KONGSKILDE rotary tedder can only perform the sults from the improper use of the implement. The user usual work in agriculture. Only connect the rotary ted- bears that risk. der to a tractor which corresponds with the specifications Always observe the following safety instructions as well of the implement and is legal to use.

  • Page 9: Electro-Magnetic Compatibility (Emc)

    • Ensure that each piece of non‐ KONGSKILDE equipment fitted to the machine bears the CE mark. • The maximum power of emission equipment (radio, telephones, etc.) must not exceed the limits imposed by the national authorities of the country where you use the machine.

  • Page 10: Manual Scope And Required Training Level

    KONGSKILDE during normal operation, routine service, and maintenance. Periodic service consists of activities that are necessary to maintain the expected life of the KONGSKILDE ma- This manual does not contain all the information that re- chine. These activities have defined intervals.
  • Page 11 1 - GENERAL INFORMATION must demonstrate the ability to operate and service the KONGSKILDE machine in a correct and safe manner.

  • Page 12: Product Identification Number (Pin)

    The Product Identification Number (PIN) is a serial num- ber that identifies the implement. The serial number, model and other specifications are on the PIN plate. Provide your KONGSKILDE dealer with the model and the PIN when you order parts. ZEIL18HT00546EA Company name...

  • Page 13: Product Identification

    1 - GENERAL INFORMATION Product identification NOTE: Do not remove or change the Product Identifica- tion Number (PIN) plate on the implement. NOTE: The following figure indicates the PIN plate local- ization on Z455H. The PIN plate localization on Z555H is similar.

  • Page 14: Operator's Manual Storage On The Machine

    1 - GENERAL INFORMATION Operator's manual storage on the machine Keep this operator's manual protected and accessible on the tractor whenever you transport or operate the imple- ment. 1-10...

  • Page 15: Implement Orientation

    1 - GENERAL INFORMATION Implement orientation NOTE: To determine the left-hand side and the right-hand side of the implement, stand behind the implement and face the direction of travel during working operation. The following overhead view illustration is a general repre- sentation of the implement.
  • Page 16 1 - GENERAL INFORMATION 1-12...

  • Page 17: Safety Information

    2 - SAFETY INFORMATION 2 - SAFETY INFORMATION###_2_### Safety rules and signal word definitions Personal safety This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible death or injury. Throughout this manual you will find the signal words DANGER, WARNING, and CAUTION followed by special in- structions.

  • Page 18: General Recommendations

    2 - SAFETY INFORMATION General recommendations Most farm machinery accidents can be avoided by the • Never let the implement run without supervision. observance of a few simple safety precautions. • Always keep a first aid kit handy. • This operator’s manual contains important information •...

  • Page 19: Illustrations

    2 - SAFETY INFORMATION Illustrations WARNING Illustrations in this manual may show protective shielding open or removed to better illustrate a par- ticular feature or adjustment. Replace all shields before operating the machine. Failure to comply could result in death or serious injury. W0012A NOTE: Some of the illustrations in this manual have been obtained by photographing prototypes.

  • Page 20: Hazardous Chemicals

    2 - SAFETY INFORMATION Hazardous chemicals 1. If you are exposed to or come in contact with haz- well as the information in this manual when you ser- ardous chemicals you can be seriously injured. vice the machine. The fluids, lubricants, paints, adhesives, coolant, 4.

  • Page 21: Starting Up The Implement Safely

    2 - SAFETY INFORMATION Starting up the implement safely Before you attach the implement to the tractor, ensure that Repair immediately a damaged PTO shaft before you the tractor is in good working order and that the brakes work with the implement. are efficient, particularly if you operate on hilly ground.

  • Page 22: Traveling On Public Roads

    2 - SAFETY INFORMATION Traveling on public roads Comply with the relevant traffic regulations Passengers WARNING Do not allow passengers to ride in the tractor unless a specific seat is provided. Impact hazard! Take care when making turns. The machine During transport, the transportation of people on the top rear end swings out when changing direction.
  • Page 23 2 - SAFETY INFORMATION When you turn during transport pay attention to the over- After you finish the transport, before you leave the tractor, hang and/or oscillating weight of the implement. always lower the implement to the ground in parking po- sition, turn off the tractor engine, pull the parking brake, Use engine braking when you drive down hills.

  • Page 24: Operating The Implement Safely

    2 - SAFETY INFORMATION Operating the implement safely Never attempt to remove residues from the implement while the implement runs. Such an imprudence could cost WARNING life or limb. Always disengage the Power Take-Off (PTO) Hazard to bystanders! shaft mechanism, switch OFF the tractor engine and ap- Always sound the horn before starting the ma- ply the parking brake before you remove residues.

  • Page 25: Stopping The Implement Safely

    2 - SAFETY INFORMATION Stopping the implement safely the tractor cab, then the following precautions must be followed: WARNING • Bring the tractor engine to low idle speed. Moving parts! Some components may continue to run after • Disengage all drive systems. disengaging the drive systems.

  • Page 26: Maintenance

    2 - SAFETY INFORMATION Maintenance link arms of the tractor so that the implement cannot move to a lower position unintentionally. WARNING • Relieve the pressure, stop the engine and remove the Maintenance hazard! ignition key, before you connect or disconnect fluid Before you start servicing the machine, attach lines.

  • Page 27: Personal Protective Equipment (Ppe)

    2 - SAFETY INFORMATION Personal Protective Equipment (PPE) Wear Personal Protective Equipment (PPE) such as pro- tective clothing, eye protection, hearing protection, dust mask, hard hat, heavy gloves, work boots, and/or any other PPE that provides for the safety and protection of the individual that operates this equipment.

  • Page 28: Noise Emission

    2 - SAFETY INFORMATION Noise emission The measuring and reporting of the noise level were car- ried out according to ISO 5131. The noise level of 70 dB was measured in the cabin of the tractor where the head of the operator is usually situated. Use hearing protectors if the noise from the implement is annoying or if you work with the implement for a consid- erable period in a tractor cabin that has not a adequate...

  • Page 29: Implement Stability

    2 - SAFETY INFORMATION Implement stability The combination of your tractor and implement can become unstable, due to the additional weight that the implement adds to the tractor. In order to guarantee stable and safe transport, you must check if you need ballast weights for transport and field work.

  • Page 30: Ecology And The Environment

    KONGSKILDE dealer, who will dispose of the used this legislation. Where no legislation exists, obtain in- batteries or recycle the used batteries properly. In some formation from suppliers of oils, filters, batteries, fuels, countries, this is a legal requirement.

  • Page 31: Safety Signs

    2 - SAFETY INFORMATION Safety signs The following safety signs are on your implement as a guide for your safety and for the safety of those who work with you. Walk around your implement and note the significance and location of all safety signs before you operate your implement.
  • Page 32 2 - SAFETY INFORMATION ZEIL18HT00950FA 811650220 Part number: 1650220 2-16...
  • Page 33 2 - SAFETY INFORMATION Safety sign (1) WARNING IMPROPER OPERATION OF THIS MACHINE CAN CAUSE DEATH OR SERIOUS INJURY. MAKE SURE THAT EVERY OPERATOR: -is instructed in the safe and proper use of this machine. -reads and understands the operator's manual for this machine.
  • Page 34 2 - SAFETY INFORMATION Safety sign (3) WARNING Pinch hazard! Wait for all movement to stop before you ser- vice or adjust the machine or equipment. Failure to comply could result in death or se- rious injury. W1420A Moving parts are dangerous and if the moving parts come in contact to your body the moving parts can pinch your body.
  • Page 35 2 - SAFETY INFORMATION Safety sign (6) Maximum 210 bar (3045 psi). Make sure that the hydraulic components are not exposed to more pressure than maximum 210 bar (3045 psi) as there could be a risk of explosive damage of parts. Hereby you expose yourself and others to serious danger of get- ting hit by metal parts with high speed or oil under high pressure.
  • Page 36 2 - SAFETY INFORMATION Safety sign (9) Part number: 0653390 ZEIL18HT00678AA Safety sign (10) Safety guard warning Part number: PR80-6609 PR80-6609 2-20...

  • Page 37: Controls And Instruments

    3 - CONTROLS AND INSTRUMENTS 3 - CONTROLS AND INSTRUMENTS###_3_### Information Operating principles For all information related to the description and the lo- cation of the controls to use your implement, see chap- ter “Controls and Instruments” in the operator’s manual of your vehicle.
  • Page 38 3 - CONTROLS AND INSTRUMENTS...

  • Page 39: Operating Instructions

    4 - OPERATING INSTRUCTIONS 4 - OPERATING INSTRUCTIONS###_4_### Commissioning the unit Commissioning operation The implement is provided on pallet with: • The right-hand side rotor and left-hand side rotor as- sembled. • The support wheel assembled. • The outer rotor raised. •...
  • Page 40 4 - OPERATING INSTRUCTIONS Set-up instructions - Z455H To set-up the implement proceed as follows: 1. Swing the main bracket with the support wheel to the three-point headstock. 2. Change over the main bracket (1) with support wheels from the transport/shipping position (2) to the working position (2).
  • Page 41 4 - OPERATING INSTRUCTIONS Remove the wires that fix the implement on the pallet. Lift the implement. Use a suitable lifting device. Remove the pallet from the rear side of the imple- ment. Lower and secure the right-hand side and left-hand side support feet.

  • Page 42: Installation Of The Rotor Arms

    4 - OPERATING INSTRUCTIONS Installation of the rotor arms To install the pre-assembled rotor arm (3) on to hub (2), use: • Install the hexagonal head bolt and the locknuts for each arm. • Torque the bolt (1) to 85 N·m (752 lb in). NOTE: Record the sense of rotation (A) of the rotors.

  • Page 43: Safety Guards - Installation

    4 - OPERATING INSTRUCTIONS Safety guards - Installation To install the safety guards proceed as follows: 1. Install the bars (4) on the headstock (1). Use the hard- ware (5). 2. Install the safety guards (2). Use the hardware (3). ZEIL18HT00908AA 3.

  • Page 44: Starting The Unit

    4 - OPERATING INSTRUCTIONS Starting the unit Connection to the tractor WARNING Crushing hazard! Use care when you connect and disconnect the machines. Never stand between the trac- tor and the implement when you connect the link arms. Failure to comply could result in death or se- rious injury.
  • Page 45 4 - OPERATING INSTRUCTIONS Connection of the implement to the tractor • When you attach the implement to the three-point link- age of the tractor, set the all control levers in a security position. Unintended lifting or lowering must be impos- sible.

  • Page 46: Hydraulic Connections

    4 - OPERATING INSTRUCTIONS Hydraulic connections The hydraulic system works under a high pressure. Connect the hydraulic hoses to the hydraulic rams and motors according to the advice in the instructions. When you fit the hydraulic hoses to the tractor hydraulic sockets, always ensure that the hydraulic system at the tractor as well as at the implement side is without pres- sure.

  • Page 47: Power Take-Off (Pto) Shaft - Shorten

    4 - OPERATING INSTRUCTIONS Power Take-Off (PTO) shaft – Shorten Power Take-Off (PTO) shaft length NOTE: Do not shorten your new Power Take-Off (PTO) shaft until you are certain that it is necessary. From the factory the distance from PTO to Power Input Connection (PIC) is standard on most tractor brands.
  • Page 48 4 - OPERATING INSTRUCTIONS Shortening the PTO shaft To shorten the PTO shaft proceed as follows. 1. Fasten the PTO shaft half parts to the PTO (on the tractor) and the PIC (on the implement). The PTO shaft half parts must be at the same horizontal level, opposite each other at the shortest distance from the tractor.

  • Page 49: Working In The Field

    4 - OPERATING INSTRUCTIONS Working in the field To prepare the implement for work in the field: 1. Place the implement on a level ground. 2. Connect the implement to the three-point linkage of the tractor. 3. Connect the hydraulic system to the quick action cou- pling of the tractor.
  • Page 50 4 - OPERATING INSTRUCTIONS Turning To prevent leaf damage losses when you turn the crop already spread, select a low PTO speed while at the same time you increase the forward speed. To make sure that the ratio between travel and PTO speed is correct, check the scatter pattern achieved.

  • Page 51: Stopping The Unit

    4 - OPERATING INSTRUCTIONS Stopping the unit Disconnection and parking 1. Place the implement on a firm and level ground. 2. Disconnect all the hydraulic couplers. 3. Disconnect the electrical connection. 4. Disconnect the Power Take-Off (PTO) shaft from the tractor.
  • Page 52 4 - OPERATING INSTRUCTIONS 4-14...

  • Page 53: Transport Operations

    5 - TRANSPORT OPERATIONS 5 - TRANSPORT OPERATIONS###_5_### Preparing for road transport Transport position Adjustment of the headstock with lateral flotation equipment NOTICE: Adhere to the maximum permissible axle loads, total weights. NOTICE: Adhere to the permissible transport measure- ments. NOTICE: Fit and check transport gear, traffic lights, warn- ing and safety signalization and safety guards.
  • Page 54 5 - TRANSPORT OPERATIONS 3. Raise the left-hand side rotor assembly and the right- hand side rotor assembly and check the safety locks (1). See Figure 1. NOTE: You can use an hydraulic device which allows to put the outer rotors in vertical position. NOTE: The warning plates front and rear shall be in ver- tical position when you lift the implement for transport.

  • Page 55: Working Operations

    6 - WORKING OPERATIONS 6 - WORKING OPERATIONS###_6_### General information Implement overview The tedder is an implement for the following operations: • Tedding. • Turning. • Clearing of windrows or small nights swaths. For the road transport, especially for narrow roads, the implement is equipped with a hydraulic system that moves the outer rotors to the vertical position.

  • Page 56: Tine Arms - Adjustment

    6 - WORKING OPERATIONS Tine arms - Adjustment It is possible to change the tine angle from the standard angle of 8° to 2°. Stepper position of tine give more grip on the forage crop. To change the tine angle, release the securing bolts and turn the tine supports (1) for 180°...
  • Page 57 6 - WORKING OPERATIONS Adjustment of the spreading angle You can set the support wheels to different spreading an- gles. To change over unscrew wheel bracket (5) from wheel holder (6). Lift the implement to adjust the spread- ing angle. ZEIL18HT00739AA Different spreading angle are available depending on the working conditions:...

  • Page 58: Working Position

    6 - WORKING OPERATIONS Working position Working position To set the implement in working position proceed as follows: 1. Raise the implement. 2. Move the lever (1) to the front. NOTE: In this position the latch (2) is free from the locking bolt (3).

  • Page 59: Maintenance

    7 - MAINTENANCE MAINTENANCE###_7_### General information Maintenance General information WARNING Avoid injury! Follow ALL of the precautions listed below. Failure to comply could result in death or se- rious injury. W1091A CAUTION Escaping fluid! Hydraulic fluid or diesel fuel leaking under pressure can penetrate the skin and cause infection or other injury.
  • Page 60 7 - MAINTENANCE NOTICE: Do the maintenance, the service, the cleaning, and the repair with the Power Take-Off (PTO) shaft and the engine OFF. Remove the ignition key. NOTICE: Take care that oil and grease do not get in con- tact with your skin.

  • Page 61: Grease Fittings And Intervals

    7 - MAINTENANCE Grease fittings and intervals Before greasing the implement always wipe any dirt from the grease fittings. All points, except those with special notations, should be lubricated until the grease is forced out around the bear- ings and then the excess grease should be wiped off. Grease specification Use Multipurpose grease NLGI 2.

  • Page 62: Torque

    7 - MAINTENANCE Torque Minimum hardware tightening torques (in N m or lb in /lb ft) for normal assembly applica- tions unless otherwise stated The minimum hardware tightening torque on drawings, in specifications, etcetera have priority. In the following tables, torque specifications are shown following the standard ENS7001, applicable for material class 8.8 and material class 10.9.
  • Page 63 7 - MAINTENANCE Flange head bolt/Flange nut Nominal Class 10.9 in N m (lb ft) Size 2.0 N·m (1.5 lb ft) 4.6 N·m (3.4 lb ft) 9.4 N·m (6.9 lb ft) 15.9 N·m (11.7 lb ft) 38.7 N·m (28.5 lb ft) 76.5 N·m (56.4 lb ft) 134 N·m (98 lb ft) 213 N·m (157 lb ft)
  • Page 64 7 - MAINTENANCE Metric hex nuts and locknuts, Classes (CL) 05 and upward NHIL14RB00663AA Metric hex nut identification markings • (1) – Manufacturer's identification • (3) – Property class • (2) – Clockwise type markings indicate property class and may include manufacturer identification (if applied), Example: property marks 240°...

  • Page 65: Fluids And Lubricants

    7 - MAINTENANCE Fluids and lubricants KONGSKI- International KONGSKILDE Capacity Lubricant grade Item LDE specifi- specification brand name cation Grease fittings NLGI 2 M1C 137-A Power Take-Off NLGI 2 M1C 137-A (PTO) shaft Universal joints NLGI 2 M1C 137-A Rotor gearbox...

  • Page 66: Maintenance Planning

    7 - MAINTENANCE Maintenance planning Maintenance chart Grease Check Tighten Replace Maintenance action Page no. After the first 5 hours of operation Nuts and bolts After the first 10 hours of operation Hydraulic screw joints Every day 7-10 Power Take-Off (PTO) shaft Universal joints 7-11 Daily grease fittings...

  • Page 67: After The First 5 Hours Of Operation

    7 - MAINTENANCE After the first 5 hours of operation Nuts and bolts Torque again all the bolts and the nuts after the first 5 h of work. After the first 10 hours of operation Hydraulic screw joints Torque again all the hydraulic screw joints after the first 10 h of work.

  • Page 68: Every Day

    7 - MAINTENANCE Every day Power Take-Off (PTO) shaft ZEIL18HT00761FA Grease the PTO shaft (1). Use the grease: NLGI 2. 7-10...

  • Page 69: Universal Joints

    7 - MAINTENANCE Universal joints For the special design of the PTO shaft, the wide angle joint requires daily lubrication of the centering disc be- tween the universal joints. NOTE: The picture shows PTO shaft with normal joint and wide angle joint. ZEIL18HT00761FA Grease the universal joint of the PTO shaft (1).

  • Page 70: Daily Grease Fittings

    7 - MAINTENANCE Daily grease fittings Left-hand side 1. Center rotor shaft (on both sides). ZEIL18HT00973AA 2. Center rotor hinge (on both sides). ZEIL18HT00973AA 3. Outer rotor (on both sides). ZEIL18AI00169AA 7-12...

  • Page 71: Every Week

    7 - MAINTENANCE Every week Weekly grease fittings Outer rotors 1. Wheel (both sides). ZEIL18HT00972AA Center rotors 2. Wheel (both sides). ZEIL18HT00972AA Headstock 3. Pin. ZEIL18AI00154AA 7-13...

  • Page 72: Every 50 Hours

    7 - MAINTENANCE Every 50 hours Nuts and bolts Check all the bolts and the nuts every 50 h of work. Torque again if necessary. See Page 7-4. NOTE: It is particularly important to check the fixing bolts of the implement. Every year Hydraulic hoses Check all hoses every year and replace if necessary.

  • Page 73: Every 6 Years

    7 - MAINTENANCE Every 6 years Hydraulic hoses WARNING Escaping fluid! Do not disconnect hydraulic quick coupler under pressurized conditions. Make sure all hydraulic pressure is removed from the system before disconnecting hydraulic quick coupler. Failure to comply could result in death or serious injury. W0095A WARNING Escaping fluid!

  • Page 74: Storage

    7 - MAINTENANCE Storage Pressure washing Before you use pressure washing, clean the implement with compressed air. NOTE: Legislation in certain countries and good practice requires special treatment of waste water through sed- imentation and oil separation and controlled removal of residues.

  • Page 75: End Of Season Service

    7 - MAINTENANCE End of season service When the season is over, prepare the implement for the storage immediately. To prepare the implement for winter storage: 1. Clean the implement thoroughly. Dust and dirt absorb moisture and moisture increases the formation of rust. 2.

  • Page 76: Ordering Parts And / Or Accessories

    Order and install the spare parts and/or accessories at once before the next season. When you order spare parts, always make sure to give your KONGSKILDE dealer the model number and the Product Identification Number (PIN) of your implement. See “Product identification” in Chapter 1 of this opera- tor’s manual.

  • Page 77: Troubleshooting

    8 - TROUBLESHOOTING TROUBLESHOOTING###_8_### Fault code resolution Troubleshooting Problem Possible Cause Correction The implement does not The implement is in transport position. Set the implement in working position. See follow the ground. Page 6-4. The tine breaks too easy. the installation position of the tine is wrong. Turn the tine. See Page 6-2. There is too much soil in The tine goes too deep in the soil.
  • Page 78 8 - TROUBLESHOOTING...

  • Page 79: Specifications

    18 kW Z455H (11.1 Ac/hr) (24.5 Hp) 540 RPM 6 Ha/hr 22 kW Z555H (14.8 Ac/hr) (30 Hp) Fluids and lubricants KONGSKI- KONGSKILDE International Item Capacity LDE specifi- Lubricant grade specification brand name cation Grease fittings NLGI 2 M1C 137-A...
  • Page 80 9 - SPECIFICATIONS...

  • Page 81: 10 - Accessories

    10 - ACCESSORIES 10 - ACCESSORIES###_10_### General information Accessories or optional equipment listed hereafter may be part of the standard equipment for certain countries. Some of these accessories or options may not be avail- able in certain markets. Dual speed gearbox The dual speed gearbox (1) permits to reduce the speed of the rotors by 1/3.

  • Page 82: Tine Safety Lock

    10 - ACCESSORIES Tine safety lock You can fit the tine safety lock (1) to prevent the tine loss if a tine should break during work. This option is recommended in rough terrain where the tines risk to hit soil when runs across the field. Also, if you use the implement in extreme heavy silage crops, you can fit the tine safety lock.

  • Page 83: Front Gauge Wheel

    10 - ACCESSORIES Front gauge wheel To increase the ground following of the implement and get the optimal work application, the implement can be equipped on the headstock with a front gauge wheel (1). The front gauge wheel (1) reduces the risk of crop soil contamination, especially in rolling field conditions.
  • Page 84 10 - ACCESSORIES 10-4...

  • Page 85: Forms And Declarations

    11 - FORMS AND DECLARATIONS 11 - FORMS AND DECLARATIONS###_11_### EC Declaration of Conformity EF-overensstemmelseserklæring/ EG-Konformitätserklärung/ EC Declaration of Conformity/ Déclaration CE de con- formité/ Dichiarazione CE di conformita/ EG Verklaring van Overeenstemming/ EG-försäkran om överensstämmelse/ EY-vaatimustenmukaisuusvakuutus/ Declaración de conformidad CE/ Deklaracja Zgodności WE./ Декларация за съответствие...
  • Page 86 11 - FORMS AND DECLARATIONS ZEIL19TL0016EA - er i overensstemmelse med Maskindirektivets bestemmelser (Direktiv 2006/42/EF) og hvis relevant også bestem- melserne i EMC-direktivet 2014/30/EU - In übereinstimmung mit den Bestimmungen der Maschinen-Richtlinie 2006/42/EG und wenn erforderlich auch mit der EMC-Richtlinie 2014/30/EU hergestellt wurde. - is in conformity with the provisions of the Machinery Directive 2006/42/EC and if relevant also the provisi¬ons of the EMC Directive 2014/30/EU.
  • Page 87 11 - FORMS AND DECLARATIONS - z določili Direktive o strojih 2006/42/ES ter, če je to relevantno, tudi z določili EMC Direktive 2014/30/EU. - παραμένει σύμφωνη με τους όρους της Οδηγίας περί Μηχανών 2006/42/ΕΚ και σε περίπτωση που αυτό εφαρμόζεται και...
  • Page 88 11 - FORMS AND DECLARATIONS 11-4...
  • Page 89 Index ###_Index_### Adjustment of the support wheels ........Anti-wrap disc for the wheel rim.
  • Page 90 Nuts and bolts ........7-9, 7-14, 7-14 Operating principles .
  • Page 92 Printed in U.S.A. Printed in Italy Kongskilde is a trademark registered in the United States and many other countries, owned or licensed to CNH Industrial N.V., its subsidiaries or a liates. © 2018 CNH Industrial America LLC. All Rights Reserved.

This manual is also suitable for:

Z 555 h

Table of Contents