10-Gigabit CX4 copper cable (for interconnecting devices) NOTE: • HPE 10-Gigabit transceiver modules and cables are subject to change over time. For the most recent list of HPE 10-Gigabit transceiver modules and cables, contact HPE technical support or marketing staff.
Transmission distances supported by optical transceiver modules are mainly limited by signal attenuation and dispersion suffered during the transmission of fiber signals over fibers. Signal attenuation occurs because of absorption, dispersion, and leakage over the media as • light travels through optical fibers. This attenuation increases in direct ratio to transmission distance.
Fiber diameter is expressed as core diameter/cladding diameter, in μm. For example, 9/125 μm represents a fiber core diameter of 9 μm and a fiber cladding diameter of 125 μm. As a best practice, use the following fiber diameters for the HPE Comware-based devices: G.652 standard single-mode fiber—9/125 μm.
Connectors connect transceiver modules to the transmission media. Figure 1 LC connector Optical parameters The following are the major optical parameters: Transmit power—Transmit power is the power at which the transmitter of an optical • transceiver module transmits optical signals, in dBm. Receive power—Receive power is the power at which the receiver of a optical transceiver •...
(nm) (µm) (MHz*km) 2000 300 m (984.25 ft) 50/125 82 m (269.03 ft) HPE X130 10G JD092B SFP+ LC SR 66 m (216.54 ft) Transceiver 33 m (108.27 ft) 62.5/125 26 m (85.30 ft) 2000 300 m (984.25 ft)
Page 10
Transceiver NOTE: • A mode conditioning patch cord is required when you use OM1 or OM2 fiber types on an HPE X130 10G SFP+ LC LRM Transceiver (JD093B). Never use mode conditioning patch cords for OM3 fiber types. For more information about mode conditioning patch cords, see related parts in the IEEE 802.3 standard.
HPE X230 Local Connect 50cm CX4 JD363B 0.5 m (1.64 ft) Cable Used for interconnecting HPE X230 Local Connect 100cm 12 Gbps JD364B 1 m (3.28 ft) deices, and CX4 Cable supports IRF JD365A HPE X230 CX4 to CX4 3m Cable 3 m (9.84 ft)
10-Gigabit Ethernet transceiver modules Before you install, configure, or upgrade a device with HPE 10-Gigabit Ethernet transceiver modules, always see the device's release notes for latest information. This compatibility matrix does not replace or supersede the release notes.
HPE X240 10G SFP+ SFP+ 1.2m Direct Attach Copper R1005P07 Cable (JD096B) HPE X240 10G SFP+ SFP+ 1.2m Direct Attach Copper R1005P07 Cable (JD096C) HPE X2A0 10G SFP+ to SFP+ 7m Active Optical Cable F1033L05 (JL290A) HPE X2A0 10G SFP+ to SFP+ 10m Active Optical F1033L05 Cable (JL291A)
Page 19
HPE X240 10G SFP+ SFP+ 1.2m Direct Attach Copper R1005P07 Cable (JD096B) HPE X240 10G SFP+ SFP+ 1.2m Direct Attach Copper R1005P07 Cable (JD096C) HPE X2A0 10G SFP+ to SFP+ 7m Active Optical Cable F1033L05 (JL290A) HPE X2A0 10G SFP+ to SFP+ 10m Active Optical F1033L05 Cable (JL291A)
Page 20
HPE X240 10G SFP+ SFP+ 1.2m Direct Attach Copper R1109 Cable (JD096C) HPE X240 10G SFP+ SFP+ 7m Direct Attach Copper R1109 Cable (JC784C) HPE X2A0 10G SFP+ to SFP+ 7m Active Optical Cable R2138 (JL290A) HPE X2A0 10G SFP+ to SFP+ 10m Active Optical R2138 Cable (JL291A)
Page 21
Cable (JL292A) HPE 10GBase-T SFP+ Transceiver (813874-B21) R2710 NOTE: For the HPE FlexFabric 12900 48-port 1/10GbE SFP+ FE Module (JH249A), when using the HPE 10GBase-T SFP+ Transceiver (813874-B21) only add ports are supported and link-up only happens at auto-negotiation mode.
R2609 NOTE: For the HPE FlexFabric 12900E 48-port 1/10GbE SFP+ 2-port 100GbE QSFP28 HB Module (JH360A) and HPE FlexFabric 12900E 48-port 10GbE SFP+ HF Module (JQ061A), when using the HPE 10GBase-T SFP+ Transceiver (813874-B21) only add ports are supported and link-up only happens at auto-negotiation mode.
R2138P01 Cable (JL292A) NOTE: For the HPE FlexFabric 7900 24-port 1/10GbE SFP+ FX Module (JG845A), when using the HPE 10GBase-T SFP+ Transceiver (813874-B21) only add ports are supported and link-up only happens at auto-negotiation mode. HPE FlexFabric 7500 switch series minimum software...
Document conventions and icons Conventions This section describes the conventions used in the documentation. Command conventions Convention Description Boldface Bold text represents commands and keywords that you enter literally as shown. Italic Italic text represents arguments that you replace with actual values. Square brackets enclose syntax choices (keywords or arguments) that are optional.
Network topology icons Convention Description Represents a generic network device, such as a router, switch, or firewall. Represents a routing-capable device, such as a router or Layer 3 switch. Represents a generic switch, such as a Layer 2 or Layer 3 switch, or a router that supports Layer 2 forwarding and other Layer 2 features.
Support and other resources Accessing Hewlett Packard Enterprise Support For live assistance, go to the Contact Hewlett Packard Enterprise Worldwide website: • www.hpe.com/assistance To access documentation and support services, go to the Hewlett Packard Enterprise Support • Center website: www.hpe.com/support/hpesc Information to collect •...
Hewlett Packard Enterprise is committed to providing documentation that meets your needs. To help us improve the documentation, send any errors, suggestions, or comments to Documentation Feedback (docsfeedback@hpe.com). When submitting your feedback, include the document title, part number, edition, and publication date located on the front cover of the document. For online help content, include the product name, product version, help edition, and publication date located on the legal notices page.
Page 63
Index A C L M N S Models and specifications,9 Models and specifications,12 About optical transceiver modules,1 Accessing Hewlett Packard Enterprise Support,56 Accessing updates,56 Network topology icons,55 Conventions,54 SFP+ active optical cables,7 SFP+ copper cables,7 SFP+ optical transceiver modules,5 List of 10-Gigabit transceiver modules and network Switching minimum software release cables,1 requirements,14...