Jets Control; Light Control; Additional Functions - Caldera Makena Owner's Manual

JETS CONTROL

The JETS hard button activates the jet pump(s). When the JETS hard button
is pressed, the jets menu will be displayed on the control panel with low
speed on Jet 2 turned on, the Jet Pump icon will also be displayed.
Press any of the soft keys next to the description to change the jet
functions between high, low speed (when available), or off.
The Jet pump icon will remain displayed until the button is pressed to
turn off the jet pump(s), or after one hour of continuous operation when
the pump(s) is automatically shut off
by the control system.
The jet pump(s) will turn themselves off
after one hour of continuous operation to
prevent overheating and conserve energy.
The jets can be restarted again with no
delay.
You may also activate the jet pumps
by pressing the JETS hard button as follows:
MAKENA, SALINA, MARTINIQUE, SEYCHELLES & REUNION
1st Press = Jet 2 on Low
3rd Press = Both Jets on High
speed
5th Press = Jet 1 on High
KAUAI
1st press = Jet 1 on High

LIGHT CONTROL

Press the LIGHTS hard button to activate all lights and display the
Lighting Options screen.
The LIGHTS hard button can also be used to cycle through the light
zones as follows:
1st press: Lights On
2nd press: Lights reduce to brightness 2
3rd press: Lights reduce to brightness 1
4th press: All Lights Off
Press the soft button next to one of
the 3 lighting description to do the
following:
• Turn the lights ON or OFF
• Select the color (or choose LOOP
to cycle through all the colors)
• Adjust the brightness of the color with the Dimmer function.
Dimmer sequence is: Dimmer 3 = high light level, Dimmer 2 = medium
light level, and Dimmer 1 = low light level.
Color sequence is: 1) Indigo
6) Magenta 7) Loop On 8) Loop Off
2nd Press = Jet 2 on High
4th Press = Jet 2 on Low, Jet 1 on
High
6th Press = Jets 1 & 2 off
2nd press = Jet 1 off
2) Aqua 3) Emerald 4) Gold 5) Ruby

ADDITIONAL FUNCTIONS

SUMMER TIMER
Your spa is equipped with a summer timer. The summer timer can be
activated during hot summer months to maintain water temperature.
Activating the summer timer causes the heater to immediately shut
down. The circulation pump will remain on for approximately 5 minutes
pushing water through the heater to cool it down. Both heater and
circulation pump will then remain off for eight hours. The summer
timer icon will be displayed on the main control panel and will remain
displayed for as long as the summer timer mode is on. The circulation
pump and heater will automatically shut down for the same eight hours
every day until the summer timer
is deactivated. It is recommended
to activate the summer timer in the
morning so that the spa is off during
the hottest part of the day and so that
the circulation pump will start up again
in the evening when you are ready to
enjoy the spa.
IMPORTANT: The summer timer will not lower the spa's water
temperature below the ambient air temperature. Ambient conditions,
including humidity, wind and shading will affect your spa water
temperature.
To activate the Summer Timer, simply follow these steps:
Press the OPTIONS Hard button on the Main Control panel.
Press the soft button next to Set up.
Press the soft button next to Summer Timer to activate. The Summer
timer icon will display when activated.
IMPORTANT: If water temperature falls below 26.7°C (80°F) the
summer timer will automatically be disabled. The Summer Timer should
be deactivated when cooler temperatures return. To do this, simply
repeat step above. The Summer Timer icon will turn off.
BRIGHTNESS
If you would like to change the screen brightness of the Main Control
panel:
Press the OPTIONS Hard button on the Main Control panel.
Press the soft button next to Set-up.
Press the soft button next to Brightness to lower the brightness from 7
down to 1.
IMPORTANT: Pressing the Brightness soft button at number 1 will
increase the screen brightness back to 7.
LANGUAGE
The Main Control panel screen can be viewed in seven different
languages. The languages are English, French, German, Dutch,
Swedish, Norwegian, and Spanish. To change languages:
Press the OPTIONS hard button on the
Main Control panel.
Press the soft button next to Set-Up.
Press the soft button next to More.
Press the soft button next to Language
until the desired language is visible.
IMPORTANT: Should you accidently
change the language screen into a language you don't know, simply
repeat the previous steps.
Page 16
Operating Instructions