Installation Safety Precautions DANGER • Please read this User’s Manual in its entirety before using the grill. • Failure to follow the provided instruction can result in If you smell gas: seriously bodily injury and/or property damage. • Some parts of this grill may have sharp edges. Please wear suitable protective gloves.
TABLE OF CONTENTS For Your Safety……………………………………………………………………….2 Grill Service Center…………………………………………………………………...2 Product Record Information………………………………………………………...…..2 Installation Safety Precautions……………………………………………………..…2 Safety Symbols…………………………………………………………………..…..2 Kenmore Grill Warranty……………………………………………………..……..…4 Use and Care……………………………………………………………..………...5-11 Parts List…………………………………………………………………………..12 Parts Diagram………………………………………………………………...…..…..13 Before Assembly……………………………………………………………...…..14-16 Assembly………………………………………………………………….……...17-29 Troubleshooting…………………………………………………………...……..30-32 WARNING Combustion byproducts produced when using this product include...
Sears authorized service representative..13-15 For warranty coverage details to obtain free repair or replacement, visit the web page: www.kenmore.com/warranty . 27-29 All warranty coverage excludes igniter batteries and grill part paint loss, discoloration or surface rusting, which are either expendable parts that can wear out from normal use within the warranty period, or are conditions that can be the result of normal use, accident or improper maintenance.
USE AND CARE LP Cylinder • The LP cylinder used with your grill must meet the following requirements: DANGER • Use LP cylinders only with these required measurements: 12" (30.5cm) (diameter) x 18" (45.7 cm) (tall) with 20 lb. (9 kg.) Capacity maximum.
Page 6
LP Tank Exchange Connecting Regulator To The LP Tank • Many retailers that sell grills offer you the option of replacing 1. LP tank must be properly secured onto grill. (Refer to your empty LP tank through an exchange service. Use only those assembly section.) reputable exchange companies that inspect, precision fill, test 2.
Page 7
Leak Testing Valves, Hose and Regulator 1. Turn all grill control knobs to OFF. 2. Be sure regulator is tightly connected to LP tank. 3. Completely open LP tank valve by turning OPD hand wheel counterclockwise. If you hear a rushing sound, turn gas off immediately.
Page 8
Safety Tips WARNING ▲ Before opening LP cylinder valve, check the coupling nut for tightness. ▲ When grill is not in use, turn off all control knobs and LP cylinder For Safe Use of Your Grill and to Avoid Serious valve.
Page 9
Burner Flame Check WARNING • Remove cooking grates and flame tamers. Light burners, rotate knobs from HIGH to LOW. You should see a smaller flame in LOW position than seen on HI. Always check flame prior to each use. If only low flame Turn controls and gas source or tank OFF is seen refer to "Sudden drop or low flame"...
Cleaning the Burner Assembly CAUTION Follow these instructions to clean and/or replace parts of burner assembly or if you have trouble igniting grill. 1. Turn gas off at control knobs and LP cylinder SPIDER ALERT! SPIDER ALERT! SPIDER ALERT! 2. Remove cooking grates and heat diffusers. 3.
Page 11
Food Safety Indirect Cooking Food safety is a very important part of enjoying the outdoor Poultry and large cuts of meat cook slowly to perfection on the grill cooking experience. To keep food safe from harmful bacteria, by indirect heat. Place food over unlit burner(s); the heat from lit follow these four basic steps: burners circulates gently throughout the grill, cooking meat or Clean: Wash hands, utensils, and surfaces with hot soapy water...
PARTS LIST Description Qty Part Number Description Qty Part Number A01-A Lid(Black) 30400004A Hook 40800123 A01-B Lid (Red) 30400004B Side Shelf Handle 40800099 A01-C Lid (Teal) 30400004C Tank holder 20700049 A01-D Lid (Pearl) 30400004D Cotter pin 110050 A01-E Lid (Azure) 30400004E D03-A Grill Base (Black) 30400404A...
BEFORE ASSEMBLY NOTICE: Once you have unpacked the grill, check all the grill parts against the pictures on this and the following two pages. If any parts are missing or damaged, please call 1-888-287-0735...
ASSEMBLY CAREFULLY READ AND PERFORM ALL ASSEMBLY INSTRUCTIONS ON THE FOLLOWING PAGES. Tools Required: Adjustable wrench (not provided) Screwdriver (not provided) 7/16” Combination wrench (not provided) The following hardware is provided in a blister pack for convenient use. M4X10 screw M6X13 screw AA Battery...
Page 18
Grill Base Turn the Grill Base upside down. Remove the Tank Holder from the underside of the base. Set tank holder aside. Use (4) M6x13 screws each to attach the Swivel Caster to the corner on your left and the Standard Caster to the corner on your right.
Page 19
Grill Base Twist each Swivel Caster with Brake into the other two corners of the grill base. Use the wrench provided to firmly tighten the casters in place. Turn the grill base right side up. Insert the ends of the tank holder into the two holes as shown. ...
Page 20
Pedestal Attach but do not fully tighten the panel support angle bars to left and right side panels with (2) M4x10 screws. Attach (3) M4x10 screws to left and right side panels as shown, leaving a 1/8" - 5/32" gap between panel and head of screw.
Page 21
Pedestal A- Attach front panel to left side panel. Push wide ends of key holes over screw heads and slide front panel down. Fully tighten screws. B- Attach front panel to right side panel. Push wide ends of key holes over screw heads and slide front panel down.
Page 22
Pedestal Use (6) M6x13 screws as shown to attach pedestal panels to grill base. Use (2) M4x10 screws as shown to attach each panel support angle bar to grill base. Fully tighten screws left partially tightened in step 3. M6X13 screw Qty: 6 pcs M4 X10 screw Qty: 4 pcs...
Page 23
Pedestal Use (6) M4x10 screws to attach the Back Rail to the rear of the pedestal as shown. M4x10 screw Qty: 6 pcs...
Page 24
Grill Head to Pedestal CAUTION: To avoid possible injury, two people are required to perform this step. Remove any wire ties holding the regulator and gas hose under the grill head, making sure the hose hangs freely. With the aid of an assistant, carefully lower the grill head onto the pedestal. ...
Page 25
Attach the 4 side shelf support brackets to firebox with (8) M6x13 screws, as shown. There is a location label on each bracket. M6X13 screw Qty: 8 pcs...
Page 26
Folding Side Shelves Perform the procedure below for both the Left and Right Side Shelf. Left side is shown below. Slide 3 accessory hooks onto the shelf handle in the orientation shown below. Hook ends must face away from grill body. ...
Page 27
Raise and Lower Shelves To raise the shelves, grasp shelf by sides and lift up until slots at bottom of shelf braces clear lower shoulder screws in shelf support brackets. Lower shelf slightly for slots to secure onto screws. To lower the shelves, grasp shelf by sides and lift up to raise brace slots from bracket shoulder screws.
Page 28
Heat Diffusers, Cooking Grids, Warming Rack: Place heat diffusers over burners. Diffusers will fit in firebox in either direction. Fit tabs in firebox front through slots in diffuser tips. Fit diffuser tips beside tabs in firebox rear. Place cooking grates onto grate rests. ...
Page 29
Drip Cup LP tank is sold separately. Use only with an OPD (over-fill protection device) equipped LP tank. Fill and leak check before attaching to grill and regulator. Place LP tank into hole in grill base with tank collar opening facing to back as shown. Raise tank holder to hold LP tank securely in place.
EMERGENCIES: If a gas leak cannot be stopped, or a fire occurs due to gas leakage, call the fire department. Problem Possible Cause Prevention / Solution Gas leaking from •Turn off gas at LP cylinder or at source on natural gas systems. •...
Page 31
Troubleshooting (continued) Prevention / Solution Problem Possible Cause Prevention/Solution Burner(s) will not light ELECTRONIC IGNITION: • See Section I of Electronic Ignition System. using igniter. • No spark, no ignition noise. (See Electronic • See Section II of Electronic Ignition System. Ignition •...
Troubleshooting - Electronic Ignition Check Item Prevention / Solution Problem Possible Cause • Battery not installed SECTION I • Check battery orientation. • Install battery (make sure that “+” and “-” properly. No sparks appear at connectors are oriented correctly, with “+” end any electrodes when up and “-”...
Page 33
Kenmore ® Customer Care Hotline To schedule in-home repair service or order replacement parts Para pedir servicio de reparación a domicilio, y ordenar piezas 1-844-553-6667 www. kenmore. com ®...