Table of Contents
Advertisement
Quick Links
Mini4 User's Manual
(201580-xxx And 201590-xxx)
And
Troubleshooting Guide
February 23, 2009
Rev C
Moog Components Group
Springfield Operations
750 West Sproul Road
Springfield, PA 19064
E-Mail:
mcg@moog.com
URL:
www.moog.com/components
Tel: 610-328-4000 Fax 610-605-6216
24/7 Technical Customer Support Hotline: 610-605-6101
Advertisement
Table of Contents
Related Manuals for Moog PRIZM Mini4 Series
Summary of Contents for Moog PRIZM Mini4 Series
- Page 1 Mini4 User’s Manual (201580-xxx And 201590-xxx) Troubleshooting Guide February 23, 2009 Rev C Moog Components Group Springfield Operations 750 West Sproul Road Springfield, PA 19064 E-Mail: mcg@moog.com URL: www.moog.com/components Tel: 610-328-4000 Fax 610-605-6216 24/7 Technical Customer Support Hotline: 610-605-6101...
-
Page 2: Table Of Contents
Moog Components Group Mini4, Rev C February 23, 2009 (201580-xxx And 201590-xxx) TABLE OF CONTENTS Mini4 Video Input with SFP Board P/N – 201580-xxx and Mini4 Video Output with SFP Board P/N – 201590-xxx .. 3 Mini4 Video Input and Output Board Revision History: ............... ..3 Mini4 Video Input and Output Board Dash (-) Number Definitions: ............ -
Page 3: Mini4 Video Input With Sfp Board P/N - 201580-Xxx And Mini4 Video Output With Sfp Board P/N - 201590-Xxx
Moog Components Group Mini4, Rev C February 23, 2009 (201580-xxx And 201590-xxx) 1 Mini4 Video Input with SFP Board P/N – 201580-xxx and Mini4 Video Output with SFP Board P/N – 201590-xxx The Mini4 (M4) Video Input and Output boards are used as a set; the Input Board is used at the system location where the video sources are located while the Video Output board is connected to the video monitor located at the system location where the video is to be displayed. - Page 4 Moog Components Group Mini4, Rev C February 23, 2009 (201580-xxx And 201590-xxx) video analog-to-digital converters (ADCs) and the data interface chips) through a programmable logic device. The boards also provide the interface for a daughter board connection.. A block diagram of the basic Mini4 Video Input and Output Board I/O is shown on the following page and explained in the subsequent paragraphs.
-
Page 5: Mini4 Video Input Board Indicator And Controls
Moog Components Group Mini4, Rev C February 23, 2009 (201580-xxx And 201590-xxx) 1.3.1 Mini4 Video Input Board Indicator and Controls LEDS: There are 21 surface mount (SMD) LED indicators on the Mini4 Video Input board to indicate different statuses that are covered by function below. - Page 6 Moog Components Group Mini4, Rev C February 23, 2009 (201580-xxx And 201590-xxx) Located on the left bottom of the board, section labeled ‘VID #4’, provides an D37 (Green) indication of the presence of an input signal on video channel #4. When ‘ON’...
- Page 7 Moog Components Group Mini4, Rev C February 23, 2009 (201580-xxx And 201590-xxx) received into the board on channel 1, Red is ‘ON’ when serial data is being (Red/Green) transmitted out of the board on channel 1. FUSES: a 2.6A PTC fuse, F3, protects the +5VDC input to the board.
- Page 8 NOTE: J11 header is located at the bottom center side of the board. Pin 1 is the upper right pin – as identified by a square pad. NOTE: J11 header is to be with a PRIZM display board only. Contact MOOG COMPONENTS GROUP if details are required. ISP Header +3.3V...
-
Page 9: Mini4 Video Output Board Indicator And Controls
Moog Components Group Mini4, Rev C February 23, 2009 (201580-xxx And 201590-xxx) JP2: RS-485/RS-422 Selection for channel 6 1 o o 2 1 o o 2 for RS-485 for RS-422 3 o o 4 3 o o 4 JP3: RS-485 Receiver Termination Enable for channel 6... - Page 10 Moog Components Group Mini4, Rev C February 23, 2009 (201580-xxx And 201590-xxx) the remote unit. Labeled ‘2.5V’, located on the mid-right of the board. When ‘ON’ indicates the on- D6 (Green) board 2.5V converter is operational Not labeled, located on the bottom center of the board. When ‘ON’ indicates that 5V D7 (Green) is available to the display LED ribbon header.
- Page 11 Moog Components Group Mini4, Rev C February 23, 2009 (201580-xxx And 201590-xxx) stream is synchronized Located on the upper right of the board. Green is ‘ON’ when serial data is being received into the board on channel 6, Red is ‘ON’ when serial data is being (Red/Green) transmitted out of the board on channel 6.
- Page 12 Moog Components Group Mini4, Rev C February 23, 2009 (201580-xxx And 201590-xxx) Power /Diagnostics o o 2 o o 4 o o 6 o o 8 o o 10 Serial Data o o 2 GND_ISO_A o o 4 GND_ISO_A o o 6...
- Page 13 Moog Components Group Mini4, Rev C February 23, 2009 (201580-xxx And 201590-xxx) R4_LED o o 18 T4_LED R5_LED o o 20 T5_LED R6_LED o o 22 T6_LED RDIAG_LED o o 22 TDIAG_LED NOTE: J11 header is located at the bottom center side of the board.
-
Page 14: Mini4 Video Input And Output Board Specifications
Moog Components Group Mini4, Rev C February 23, 2009 (201580-xxx And 201590-xxx) JP5: RS-485/RS-422 Selection for channel 5 1 o o 2 1 o o 2 for RS-485 for RS-422 3 o o 4 3 o o 4 JP6: RS-485 Receiver Termination Enable for channel 5... -
Page 15: Mini4 Video Input And Output Board Dimensions
Moog Components Group Mini4, Rev C February 23, 2009 (201580-xxx And 201590-xxx) Video Quantizing Levels: 10 bits or 1024 levels Video Sample Rate: 12.5 Msps, typically Onboard Data Channels Number of Data Channels: 4 x RS-232, 2 x RS-485/422 RS-232 Data Rates:... -
Page 16: Power Section Testing
Moog Components Group Mini4, Rev C February 23, 2009 (201580-xxx And 201590-xxx) 1.3.6 Power Section Testing NOTE: There are connectors on the bottom of the Video Input and Output boards have pins that are connected to +5VDC and ground. If these pins are inadvertently shorted together or to a common chassis ground, the board fuse (F3 on Input/F4 on Output) will blow. -
Page 17: Video Section Testing
Moog Components Group Mini4, Rev C February 23, 2009 (201580-xxx And 201590-xxx) To determine if the fiber is broken, a laser module is out, or the board is malfunctioning, first: Verify that the optical transceiver is tight in its socket. -
Page 18: Stack Mini4 System Installation Checkout Procedure
Moog Components Group Mini4, Rev C February 23, 2009 (201580-xxx And 201590-xxx) On the other end of the link, attach the other computer used for RS-485 testing to the same pins of connector J3 of the Mini4 RS-485 channel. This will allow the two RS-485 test computers to talk to each other through the Mini4 boards. -
Page 19: Diagnostics Overview
Moog Components Group Mini4, Rev C February 23, 2009 (201580-xxx And 201590-xxx) 1.4 Diagnostics Overview The Mini4 Video Input and Output boards have been designed to include hardware and firmware for monitoring various real-time parameters of interest on the boar. This capability is accessed via a black3- pin Phoenix connector on the right side of the board that carries bi-directional RS-485 telemetry to/from the monitoring PC to the Mini4 boards.