Burkert 3003 Quick Start Manual

Burkert 3003 Quick Start Manual

Electrical rotary open/close actuator

Advertisement

Type 3003
Electrical rotary O
/C
pen
lOse
Elektromotorischer Drehantrieb A
Actionneurs électriques O
uvert
Quickstart
English
Deutsch
actuator
/Z
uf
u
/f
ermé
Français

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 3003 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Burkert 3003

  • Page 1 Type 3003 Electrical rotary O actuator lOse Elektromotorischer Drehantrieb A Actionneurs électriques O uvert ermé Quickstart English Deutsch Français...
  • Page 2 We reserve the right to make technical changes without notice. Technische Änderungen vorbehalten. Sous réserve de modifications techniques. © 2011 - 2016 Bürkert Werke GmbH Operating Instructions 1601/02_EU-ML_00809485 / Original DE...
  • Page 3: Table Of Contents

    Type 3003 Contents  1 QUICKSTART ....................4 8 INSTALLATION .................... 11 Definition of the term “device” ..........4 Safety information..............11 Power and control connections ...........11 2 SYMBOLS ......................4 Connecting the additional limit switches (optional) ..11 3 INTENDED USE .....................5 Setting the limit switches ............12...
  • Page 4: Quickstart

    The Quickstart explains, for example, how to install and start-up the CAUTION! device. A detailed description of the device can be found in the operating Warns of a possible danger! instructions for Type 3003. ▶ Failure to observe this warning may result in a moderately severe or minor injury. NOTE! 1.1 Definition of the term “device”...
  • Page 5: Intended Use

    Type 3003 Intendeduse INTENDED USE GENERAL SAFETY INFORMATION This safety information does not cover: Non-authorized use of the electromotive rotary actuator type 3003 may be dangerous to people, nearby equipment and the • Haphazard situations that can arise during installation, operation and maintenance of the use. environment. ▶ The device may be used outside. • Locally applicable safety regulations which the operator and instal- ▶...
  • Page 6 NOTE! To prevent injury, ensure: Electrostatically sensitive components / modules! • The electrical rotary actuator Type 3003 may not be used in poten- The device contains electronic components that react sensitively tially explosive atmospheres (in this case please use type 3004). to electrostatic discharge (ESD). Contact with electrostatically ▶...
  • Page 7: General Information

    The rotary actuator is fitted with a type label which enables clear iden- 5.3 Informations in the Internet tification and provides the most important technical data. The operating manual and the data sheets on Type 3003 can be found on the Internet under: www.burkert.com english...
  • Page 8: Type Label

    Do not remove the type label from the rotary actuator! It is extremely important for identification during installation 7.1 Conformity and maintenance. The electromotive rotary actuator Type 3003 conforms to the EC The warranty is void without the type label. Directives according to the Declaration of Conformity. 7.2 Standards 6.4...
  • Page 9: Electrical Circuit Diagrams

    Type 3003 Technicaldata 7.5 Electrical circuit diagrams On-Off-Mode Feedback 3-point mode TP/PE TP/PE Symbol Description Limit switch ON Limit switch OFF Additional limit switch 1 Additional limit switch 2 Fig. 2: Open/Closed version If voltage is applied simultaneously to terminals 2 and 3, terminal 2 is the leading one and the actuator moves to the OPEN position.
  • Page 10 Type 3003 Technicaldata TP/PE Feedback 15V-30V 50/60 Hz (12V-48V DC) 100 V-240 V 50/60 Hz (100 V-350 V DC) TP/PE 17 18 P6 POSI 13 14 15 16 The resolution of the control mode is about 1° Motor The input resistance for control 0-10 V is 10 kΩ...
  • Page 11: Installation

    Type 3003 Installation INSTALLATION 8.2 Power and control connections Procedure: 8.1 Safety information → Disconnect the rotary actuator from the power supply. DANGER! → Remove the position indicator from the axis. → Loosen the cover screws with a screwdriver and lift the cover off.
  • Page 12: Setting The Limit Switches

    Type 3003 Installation → Wire the connections of the additional limit switches (FC1 and FC2) Electronic card according to the circuit diagram figures (see “Fig. 2” and “Fig. 3”). CLOSED Cam No. 4 → Tighten the cable gland after connecting the terminals.
  • Page 13: Circuit Board For Actuator With Standard Signal Input

    Type 3003 Installation 8.5 Circuit board for actuator with D MEM push-button LED yellow: Indicates the standard signal input power supply CLOSE push-button Potentiometer OPEN push-button Motor connection G K1 plug-in jumper Heat resistor connection To prevent electromagnetic interference, shielded cables must be used. Procedure: →...
  • Page 14: Specify Position Of The Plug-In Jumpers

    Type 3003 Installation 8.6 Specify position of the plug-in 8.7 Parameterization steps jumpers Specify direction of rotation of the shut-off valve Normal direction of rotation (preset) → Press <OPEN> push-button and switch on the card (hold down push-button). The GREEN LED lights up. → Release <OPEN> push-button and dis- connect the card from the power supply.
  • Page 15 Type 3003 Installation Learning mode Control signal when current 0 – 20 mA → Specify end positions Press <MEM> and <OPEN> push- button and switch on the card (hold → Press <OPEN> and <CLOSE> down push-button). push-button and switch on the card The RED LED lights up 3x. (hold down push-button). The RED →...
  • Page 16: Normal Operation

    Type 3003 Rotary actuators with integrated emergency reset ROTARY ACTUATORS WITH Specify end positions INTEGRATED EMERGENCY RESET All positions are now saved. → 9.1 Technical data Disconnect the card from the power supply. Voltage 18 V DC Currant nominal 0.8 A 8.8 Normal operation Max. current 2.4 A...
  • Page 17: Circuit Board

    Type 3003 Rotary actuators with integrated emergency reset Configuration A or B 18 V DC connection D Green LED* A-standard mode: If the actuator is controlled with a programmable Battery block connection Red LED ** controller, the feedback of the charge state can be connected to it.
  • Page 18: 10 Operating

    Type 3003 Operating 10 OPERATING 10.2 M anual operation of the rotary actuator The rotary actuator can be operated manually if there is a power failure. 10.1 Safety information To do this, the hand wheel must be turned to „MAN“ (see “Fig. 12”). DANGER! Procedure: →...
  • Page 19: Returning From Manual To Automatic Operation

    Type 3003 Transport,Storage,Disposal 10.3 R eturning from manual to automatic 11 TRANSPORT, STORAGE, DISPOSAL operation NOTE! Returning to automatic operation: Transport damages! → Let go off the hand wheel to switch back into automatic operation. Inadequately protected equipment may be damaged during transport. The spring force automatically resets it to the „AUTO“ position.
  • Page 20 www.burkert.com...

This manual is also suitable for:

Type 3003

Table of Contents