Related Manuals for Jofemar Vision ES-PLUS
Summary of Contents for Jofemar Vision ES-PLUS
- Page 1 Vision Es-Plus // Vending English vision ES-PLUS TECHNICAL MANUAL MNP141GBV00 Date: 2011/04/29 Rev. 0 PAGE 1 OF 24...
- Page 2 If the power cable is damaged, it should be replaced by the manufacturer or after sales service or similar qualified personnel to prevent hazards. Jofemar S.A. Ctra. de Marcilla Km.2, 31350 PERALTA. Navarra, SPAIN. http: // www.jofemar.com...
-
Page 3: Table Of Contents
Vision Es-Plus // Vending ÍNDICE Symbols .......................4 Operating conditions..................4 Description of components ................4 3.1. Main technical features................6 3.1.1 Door......................6 3.1.2 Cabinet....................6 3.2. Volume and weight................11 Electric-electronic specifications ~...............12 Initial electrical installation ~..............12 4.1. 4.2. Product dispenser channel..............13 4.3. Control card....................13 4.4. -
Page 4: Symbols
This symbol indicates that a given material should not be disposed of as domestic waste. This symbol indicates that a given material is recyclable. This symbol indicates that Jofemar is committed to the environment. Operating conditions This machine has been specifically designed to work in interiors. The machine leaves the factory adjusted to work properly at an ambient temperature between 5º... - Page 5 Vision Es-Plus // Vending Ñ WITH COOLING UNIT WITHOUT COOLING UNIT MAIN SWITCH POSITION AND RS-232 CONNECTOR WITH COOLING UNIT WITHOUT COOLING UNIT Posición Descripción Posición Descripción Door Door microswitch Lock Electronics support Product delivery opening RS-232 connection Safety glass Fuse/Fuse holder Iluminación Leds Main switch...
-
Page 6: Main Technical Features
Vision Es-Plus // Vending 3.1. Main technical features ? Dispenses a wide range of products of different sizes and shapes —different types of drinks and snacks, sandwiches, different objects, glass bottles, bread, egg cartons, etc. ? Flexible configuration and programming, up to 8 height-adjustable trays with up to 10 channels each for including various product formats. - Page 7 NOTE: For other types of products or special sizes please contact your Jofemar distributor. IMPORTANT: The minimum size for dispensing in this machine is the size of a tobacco package 23mm x 55mm x 88mm (0.905” x 2.165” x 3.465”).
- Page 8 Vision Es-Plus // Vending Electronic control system It consist of several printed circuit cards: • Control card, which governs all of the machine’s movements, and contains the power supply that provides the appropriate voltages for the logic control to move the trays motor, to move the elevator motor to move the motor the verifier of the product detector and to feed the product detection system.
- Page 9 Vision Es-Plus // Vending A. Condenser B. Fan C. Compressor D. Evaporator Fig. 04 The machine carries out defrosting cycles to prevent ice from building up in the evaporator of the cooling unit, which would have adverse effects on the unit’s performance.
- Page 10 Vision Es-Plus // Vending Dimensions Height (H) Width (W) Depth (D) 455 mm 715 mm 265 mm (17.913”) (28.149”) (10.433”) It has a product detection system based on infrared emitters and phototransistors. This way, when the infrared beam is cut off, it means there is a product inside the elevator.
-
Page 11: Volume And Weight
Vision Es-Plus // Vending These machines are fitted with holes and supplied with an anchoring kit (fig. 9) that can be used to anchor the machine to the floor (fig. 10) or to the wall (fig. 11) for greater stability and support and to prevent thefts. -
Page 12: Electric-Electronic Specifications
Vision Es-Plus // Vending Vision Es-Plus Fig. 12 Electric-electronic specifications ~ The cooling assembly, LED lighting power supply, turbine and transformer are supplied with the mains voltage for the particular country where the machine is sold. They should therefore not be handled without disconnecting the machine from mains. -
Page 13: Product Dispenser Channel
Vision Es-Plus // Vending 4.2. Product dispenser channel There are three types of different product dispensers. Depending on the type of product to be served, you can interchange these channels, offering a wide range of combinations. A maximum of 10 dispenser channels can be added to each tray. Fig. -
Page 14: Relay Card
Vision Es-Plus // Vending H. Thermometer connection Q. (Not in use) I. (Not in use) R. Set slave number J. Battery connection (temperature S. (Not in use) controller) T. Connection to master 4.4. Relay card RELAY CARD CONNECTORS A. Cooling unit enabling and lighting B. - Page 15 Vision Es-Plus // Vending POWER BOX VISION ES-PLUS 220 Vac Main switch Bipolar EMI filter 3 A. Transformer power 100 W Transformer primary 220 Vac Transformer secondary 24 Vca , 15 Vca , 11Vca 220 Vac mains protection fuse 10 A.
-
Page 16: Machine Electrical Drawing
Vision Es-Plus // Vending 4.8. Machine electrical drawing MNP141GBV00 Date: 2011/04/29 Rev. 0 PAGE 16 OF 24... -
Page 17: Installation And Start Up
Vision Es-Plus // Vending Installation and start up 5.1. Installation Do not install the machine near active heat sources (heaters, radiators, etc.). Avoid obstructing the grids located at the front of the cabinet to ensure air circulation inside, where the cooling unit motor is located (if the machine has one). Leave a distance of at least 7 centimetres between the back of machine and the wall or other items . -
Page 18: Updating The Machine Program
Vision Es-Plus // Vending 5.4. Updating the machine program The control card of the machine has been designed to use flash technology. This feature allows you to update the card program. To perform this task you need to manually lift the machine elevator until you can see the RS-232 connector. -
Page 19: Operation
Vision Es-Plus // Vending - This process is divided in two parts, the first is erasing the flash memory and the second is the program recording. 7.- When the recording program has finished communicating with the machine, a new window will appear showing the result of the process. (For more information, consult the manual of the EASYFLASH reprogramming device) Operation For the correct operation of the ES-Plus slave machine, it must be connected to a... - Page 20 Vision Es-Plus // Vending motor. ? In case of fault in the product detector, check whether the product detection LED indicator product is always on. If it is, you may have dirt in the slots that the elevator has to allow the infrared beam through.
-
Page 21: Annexes
Vision Es-Plus // Vending Annexes 8.1. Transport feet and adjustable levelling feet Once the machine is on the ground, it is advisable to remove the four (plastic) transport feet for better stability, aided with the lifting jack as follows: 1º Raise the back, unscrew and remove the two plastic feet and let the machine rest on the floor. -
Page 22: Recyclable
To manage the equipment as waste once the client has decided to dispose of it, Jofemar has set up a collection system with an Integrated Management System (ECOLEC). Please consult us for information about recycling. -
Page 23: Environment
Regulation vision The machines of the product range have been designed to European standards as accredited by the CE mark on the machine data plate. Jofemar guarantees that these machines meet applicable directives. MNP141GBV00 Date: 2011/04/29 Rev. 0 PAGE 23 OF 24... - Page 24 Vision Es-Plus // Vending Jofemar S.A. Reserves the right to introduce improvements in this model arising from its continuous research without prior notice. http:// www.jofemar.com MNP141GBV00 Date: 2011/04/29 Rev. 0 PAGE 24 OF 24...