Do you have a question about the YLCA Series and is the answer not in the manual?
Questions and answers
fariz
February 21, 2025
we use york jjonson control ylca 20 g itc 380t serial number 8152m10572167, how to lower the temperature in the chiller so it can reach 6 degrees Celsius
2 comments:
Mr. Anderson
February 21, 2025
To lower the temperature to 6°C in a York YLCA Series chiller, follow these steps:
1. Check the Setpoint: Ensure the temperature setpoint is correctly adjusted to 6°C in the chiller's control system.
2. Verify Glycol Concentration: Use the recommended ethylene or propylene glycol concentration to maintain proper heat exchange and avoid freezing issues.
3. Adjust Flow Rate: Balance the flow rate according to the corrected capacity values to maintain efficient cooling.
4. Monitor Pressure Levels: Ensure that the pressure drop is within the recommended range using the correcting factors.
5. Inspect Components: Confirm that the expansion valve, pressure transducers, and cooling circuit components are functioning correctly.
6. Ensure Proper Airflow: Check that the air-cooled condenser has adequate ventilation and that high-pressure fans are operational.
If the temperature does not reach 6°C, verify system load, ambient conditions, and potential maintenance needs.
This answer is automatically generated
fariz
February 21, 2025
Bagaimana cara menurunkan set point temperatur
fariz
February 21, 2025
we use york jjonson control ylca 20 g itc 380t serial number 8152m10572167, how to lower the temperature in the chiller so it can reach 6 degrees Celsius
1 comments:
Mr. Anderson
February 21, 2025
To lower the temperature in a York YLCA Series chiller to 6°C, follow these steps:
1. Check Glycol Concentration: Ensure the correct ethylene or propylene glycol concentration based on the required temperature. Use the pressure drop correcting factors if necessary.
2. Adjust Expansion Valve: Verify the expansion valve settings to regulate refrigerant flow for optimal cooling.
3. Monitor Pressure Settings: Ensure the condensing and liquid side pressure transducers are functioning correctly, especially in low ambient conditions.
4. Use Low Ambient Temperature Kit: If operating in low temperatures, install the low ambient temperature kit to stabilize pressure.
5. Verify Water Flow Rate: Adjust the flow rate to balance the design temperature range.
6. Inspect Heat Exchanger and Filters: Clean or replace any clogged filters and check for proper heat transfer efficiency.
7. Check Control Settings: Ensure the thermostat or controller is set to 6°C and functioning correctly.
By following these steps, the chiller should effectively lower the temperature to 6°C.
Need help?
Do you have a question about the YLCA Series and is the answer not in the manual?
Questions and answers
we use york jjonson control ylca 20 g itc 380t serial number 8152m10572167, how to lower the temperature in the chiller so it can reach 6 degrees Celsius
To lower the temperature to 6°C in a York YLCA Series chiller, follow these steps:
1. Check the Setpoint: Ensure the temperature setpoint is correctly adjusted to 6°C in the chiller's control system.
2. Verify Glycol Concentration: Use the recommended ethylene or propylene glycol concentration to maintain proper heat exchange and avoid freezing issues.
3. Adjust Flow Rate: Balance the flow rate according to the corrected capacity values to maintain efficient cooling.
4. Monitor Pressure Levels: Ensure that the pressure drop is within the recommended range using the correcting factors.
5. Inspect Components: Confirm that the expansion valve, pressure transducers, and cooling circuit components are functioning correctly.
6. Ensure Proper Airflow: Check that the air-cooled condenser has adequate ventilation and that high-pressure fans are operational.
If the temperature does not reach 6°C, verify system load, ambient conditions, and potential maintenance needs.
This answer is automatically generated
Bagaimana cara menurunkan set point temperatur
we use york jjonson control ylca 20 g itc 380t serial number 8152m10572167, how to lower the temperature in the chiller so it can reach 6 degrees Celsius
To lower the temperature in a York YLCA Series chiller to 6°C, follow these steps:
1. Check Glycol Concentration: Ensure the correct ethylene or propylene glycol concentration based on the required temperature. Use the pressure drop correcting factors if necessary.
2. Adjust Expansion Valve: Verify the expansion valve settings to regulate refrigerant flow for optimal cooling.
3. Monitor Pressure Settings: Ensure the condensing and liquid side pressure transducers are functioning correctly, especially in low ambient conditions.
4. Use Low Ambient Temperature Kit: If operating in low temperatures, install the low ambient temperature kit to stabilize pressure.
5. Verify Water Flow Rate: Adjust the flow rate to balance the design temperature range.
6. Inspect Heat Exchanger and Filters: Clean or replace any clogged filters and check for proper heat transfer efficiency.
7. Check Control Settings: Ensure the thermostat or controller is set to 6°C and functioning correctly.
By following these steps, the chiller should effectively lower the temperature to 6°C.
This answer is automatically generated