Table of Contents
Advertisement
. Initialization of Optional Setting and Input/Output Setting by Remote controller
The procedure for initialization of optional settings and input / output settings are as follows.
Normal mode (when unit is not operating)
1. Change to the optional setting mode.
Press the "CHECK" switch and the "RESET"
switch simultaneously for more than 3 seconds.
2. Selection of Optional Setting Mode
SET TEMP.
HIGH
C
O
O L
A
/
C
SERVICE
"SERVICE" is indicated and the mode
num�er is flashed.
4. Optional Setting and Input/Output Setting Initialization
HIGH
C
O
O L
ADDS RN
A C
/
SERVICE
Check to ensure that there are no problems
to restore the factory settings, and perform
to initialize.
.3 Optional Setting and Input / Output Setting
Table A Optional Setting Items for AHU CONNECTION KIT
●
No. Items
Optional Function
1
b1
Heating Temperature Compensation
Circulator Function at
2
b2
Heating Thermo-OFF
Enforced 3 Minutes
3
b3
Minimum Operation Time of
Compressor
4
b4
Change of Filter Cleaning Time
5
b5
Fixing of Operation Mode
6
b6
Fixing of Setting Temperature
Fixing of Operation as
7
b7
Exclusive Cooling Unit
8
b9
Fixing of Fan Speed
9
bb
Cooling Temperature Compensation
10
C5
d7 setting control
11
C6
Hi Speed at Heating Thermo-OFF
Press the "TEMP."
"∨" or "∧" switch,
select "07" for
the optional input
/ output setting
cancel mode, and
then press the
"CHECK" switch.
Press "CHECK" switch and the
initialization is performed.
It takes approximately 15 to 30
seconds.
Normal mode
In case that initialization is not required, press the "RESET" switch in step 4.
Individual
3. Selection of Indoor Unit
"07" flashes.
HIGH
C
O
O L
ADDS RN
A C
/
SERVICE
NOTES:
* In case of control by using two remote controllers (Master and Slave),
settings shall be operated by the master controller.
* In case of selecting the address of the indoor unit not to initialize the
optional and input / output setting, "NO FUNCTION" is displayed.
* If selecting the indoor unit address "AA", the indoor units that do not
have these initialization function cannot be restore to the factory setting.
HIGH
C
O
O L
A C
/
In case of performing to initialize the other indoor units, repeat
the procedure from step
In this case, the indoor unit address is completed to initialize,
the indication "CL" is displayed.
Setting
Setting
Condition
00
Standard (Set Temp. +4
01
Removal (Set Temp.)
○
02
Set Temp. +2
00
Not Available
○
01
Available
00
Not Available
○
01
Available
00
Standard
01
100 hours
02
1,200 hours
○
03
2,500 hours
04
No Indication
00
Not Available
×
01
Available
00
Not Available
×
01
Available
00
Not Available
×
01
Available
00
Not Available
×
01
Available
E1: 00
00
Standard (Set Temp.)
○
01
Set Temp. –1
02
Set Temp. –2
00
Cooling and heating Available
01
Only Cooling Available
○
02
Only heating Available
00
Not Available
○
01
Available
Select the address of the indoor unit
to be returned to the optional setting-
input/output factory settings.
Press the "TEMP." control ∨ or ∧
switch and select the address of the
indoor unit.
When displayed "CL",
the optional and input
ADDS RN
/ output settings are
SERVICE
initialized. (restore to
factory settings.)
3
.
Contents
C)
o
C (*1)
o
E1: 01
Set Temp. –6
C
Set Temp. –4
o
C
Set Temp. –2
o
C
o
C
o
C
o
3
Hide quick links:
Advertisement
Table of Contents
