1. Manuals
  2. Brands
  3. Bentel Manuals
  4. Control Panel
  5. Kyo 100
  6. Installation manual

Bentel Kyo 100 Installation Manual

Expandable multifunction control panel
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Manuel d'installation
des centraux d'alarme
KYO 100 / KYO 300
Security Engineering
chée de Bruxelles 408
B6040 - Charleroi (Jumet)
RC Charleroi n° 137.029
Fortis : 001-1611819-46
URL : http://www.augen.be/
Tél. : +32 (0)71 35 45 33
Fax. : +32 (0)71 35 47 82
Agréation INCERT : C-4006
Agréation UPEA AIV 017
Ministère de l'intérieur 20046930
Entreprise agréée classe 1
AUGEN S.A.
TVA : 423145 969

Advertisement

Table of Contents
loading

Related Manuals for Bentel Kyo 100

Summary of Contents for Bentel Kyo 100

  • Page 1 Manuel d'installation des centraux d'alarme KYO 100 / KYO 300 Security Engineering AUGEN S.A. chée de Bruxelles 408 B6040 - Charleroi (Jumet) TVA : 423145 969 RC Charleroi n° 137.029 Fortis : 001-1611819-46 URL : http://www.augen.be/ Tél. : +32 (0)71 35 45 33 Fax.
  • Page 2 EXPANDABLE MULTIFUNCTION CONTROL PANEL INSTALLATION MANUAL...
  • Page 3 OMNIA/4R 4 Relay Module ASD10 Wireless Smoke Detector B-MOD Teleservice Modem B-MOD/RX Teleservice and Telemonitoring Modem TELESERVICE Facility TELEMONITORING Facility FIRE CONTROL Facility BENTEL SECURITY srl. reserves the right to change the technical specifications of these products without prior notice.

  • Page 4: Table Of Contents

    General Features Attributes The System and Accessories Balance Type Technical Specifications Threshold Accessory Items Inactivity Differences between KYO 300 and KYO 100 Cycles Partitions Sensitivity IDENTIFICATION OF PARTS Voice Messages About the Control panel Zone in AND Mode MIA-D and Alison-DV Keypads...
  • Page 5 Event Description KYO 300 Rev. 1.20 and KYO 100 Rev. 1.20 Scheduler - Arming Type Description Models Options Examples Scheduler - Timers Type Description Models Options Keypad Codes - User Enable on Partitions Associated Timer User menu access Father PIN...

  • Page 6: Introduction

    The Bentel Security Suite Software and B-Mod Mo - dem (accessory items) reduce on-site time to a mini - This manual can be used with KYO 300 and KYO 100 Con - mum by allowing you to provide Teleservice (on-line trol panels.

  • Page 7: General Features

    Expanders The Control panel manages up to 32 six r 32 programmable partitions — each with own zones, zone M-IN/6 Input Expanders (16 for KYO 100) and up keypads, readers, outputs and times to 16 M-OUT/6 Output Expanders (6 Open-Collector r 195 User Codes with programmable priority and Outputs per Expander).

  • Page 8: Technical Specifications

    Alarm status; Maximum Current Ø ALISON-DV Keypads have smaller cases, 1 available for 3.5 A (1.7A for KYO 100) on-board zone, and an integrated Loudspeaker and Peripherals Microphone for use with the K3-VOX. 12 V - 7 Ah or 12 V - 17 Ah Ø...

  • Page 9: Accessory Items

    The following chart shows the Control panel accessory Readers items, and certifications. — Thermal Probe MIA-D A Backlit LCD Keypad (2 Inputs) n Differences between KYO 300 and KYO 100 ALISON-DV A Backlit LCD Keypad (1 Input) with Microphone + Loudspeaker KYO 300 KYO 100...

  • Page 10: Identification Of Parts

    IDENTIFICATION OF PARTS Please read this section carefully to get an overall view DESCRIPTION of the main components of the system and LED signals. 22 Switching power Supply connector (connected) 23 RAM chip battery holder The numbers in boldface (used in this text) refer to the 24 Serial Port RS232 descriptions in the tables and figures in this section.
  • Page 11 B– B–...

  • Page 12: Mia-D And Alison-Dv Keypads

    DESCRIPTION OPEN EXT-CARD 50 STOP ALARM Jumper: can be STOP ALARM used to disable Outputs no. 1, 2 and 3 (terminals +N1, +A1, C1-NC1-NA1, +N2, +A2, C2-NC2-NA2, +N3, +A3, C3-NC3-NA3): oo = Output Enabled (at de - fault) // = Output Disabled 51 Tamper Microswitch connector (connected) 52 Eyelet terminals: to be con -...
  • Page 13 Default Settings Stop alarm Clock Wrong 82 77 Figure 8 Alison/32LP Keypad - The 32 LEDs on ALISON/32LP Keypads represent the 32 Partitions on KYO 300 and the 16 Partitions on KYO 100 (refer to the USER MANUAL for details).

  • Page 14: Readers And Digital Keys

    n Readers and Digital Keys DESCRIPTION DESCRIPTION 63 Backlit LCD, 2 rows x 16 columns 83 Backplate anchor screw locations (2) 64 Buzzer 84 Microprocessor 64a Microphone (on ALISON-DV only) 85 Connection wires: 65 Snatch Microswitch Connector red = +; white = C; blue = R; black = – 66 Frontplate screws (2) 86 Snatch microswitch connector 67 Down flip...

  • Page 15: Input And Output Expanders

    9697 72 80 69 DESCRIPTION Status of Reader Partitions OFF = ALL the Reader Partitions are DISARMED; ON = AT LEAST ONE of the Reader Partitions BPI 5V BPI 5V is ARMED. Slow blinking = AT LEAST ONE of the Reader Partitions presents AT LEAST ONE Alarm or Tamper memory, and all Partitions are DISARMED.

  • Page 16: Installing

    INSTALLING Mounting the Main Unit n Connecting Keypads Keypads should be located in places where full control Please read this section carefully to get an overall view of of the system is required: MIA-D, Alison-DV, Alison-S the steps involved in installing the KYO300-KYO100 Main and Alison/32LP Keypads can be surface mounted on Unit.

  • Page 17: Connecting Readers

    10. Assign the Keypad Address, then set the BPI Level Proximity Readers Proximity Readers can be surface and complete the connections on the terminal mounted, or mounted to Mod. 503 outlet boxes or simi - board (refer to “Connecting BPI Peripherals” for in - lar.

  • Page 18: The Terminals

    [+F1], [+] and [RED] must not exceed 3.5 A for KYO +F Power supply to detectors (posi- 13.8 3(1) 300, or 1.7 A for KYO 100. tive), protected by fuse 37 (will be powered by the battery during (2) The current draw of BPI device [+] terminals is:...

  • Page 19: Bpi Peripherals

    Ter. DESCRIPTION v(V) I(A) Ter. DESCRIPTION v(V) I(A) BPI2 2nd branch of the BPI bus for the 13.8 3(1) Terminals for the connection of the BPI peripherals: K3-VOX Voice Board (Alison-DV + = positive protected by fuse 35 SP– only) C = Command M Power supply to Detectors (nega- –...

  • Page 20: The Wiring

    Ø up to 32 Readers (16 for KYO 100) Each wiring diagram refers to a specific type of device Ø up to 32 Input Expanders (16 for KYO 100) (BPI bus devices, Detectors and Signalling devices). Ø up to 16 Output Expanders Ø...
  • Page 21 Assigning Addresses You must assign an Address 1.Remove the frontplate in order to generate a Tamper to each of the BPI bus devices. The assigned Address status. will allow the Control panel to distinguish one device from another. The Peripheral devices are divided into 2.Connect the Keypad to the Control panel BPI BUS types: Keypads, Readers, Input Expanders, Output Ex - (terminals +, C, R, -).

  • Page 22: Bpi Bus Wiring Limitations

    BPI Level (refer to “Setting up the BPI Level”), then replace the frontplate. The KYO300 system has 8 zones, expandable to 312 zones (to 168 for KYO 100) by means of M-IN/6, n BPI bus Wiring Limitations MIA-D, Alison-DV and/or Alison/32LP Keypads and...

  • Page 23: Connecting Motion Detectors

    This system can detect Alarm, Tamper and Short-circuit n Connecting Motion Detectors on hardwired zones: Most Motion detectors have Normally-Closed Contacts Ø Zone Alarm will be signalled by an Alarm on zone (NC in the wiring diagram), and Normally-Closed Tam - no.
  • Page 24 Normally Closed balance will allow the Control panel to tact of the detector to the Control panel Tamper Line, or detect Alarm status on the zone: to a 24h zone (refer to “Connecting Tamper Contacts”). – the zone will hold Standby status whilst connected to 10 K Alarm Only The wiring diagram in Fig.

  • Page 25: Glass Break Detectors

    – the zone will trigger Tamper when open; The KYO300 accepts Fire detectors with Alarm -Repeat – the zone will trigger Alarm under all other conditions. Outputs that operate at 12 V (e.g. BENTEL SECURITY RT101, RT102 and RF501t). Zones with Double balance can detect and signal See Fig.
  • Page 26 Siren. The Siren will activate when positive 118Outputs (116 for KYO 100) Total (13.8 V) fails on the [+N] terminal; Ø [+B] is the positive power and Input of the Indoor Si - The three Outputs on the Main Unit (no. 1, 2, and 3) ren.

  • Page 27: Supervised Outputs (Kyo 300 Only)

    Connecting Tamper Terminals n Supervised Outputs (KYO 300 only) Outputs no. 1, 2 and 3 can be set up as Supervised Out - puts. This type of output must be programmed as The Tamper contacts of the security system devices Normally Closed (refer to “Attributes”...
  • Page 28 Tamper contact zones can be programmed with Normally Closed balance, in which case, the 10 KW resistors must not be connected. Panel 10 KW Figure 22 Connecting 3 Tamper contacts to the Main Unit Tamper Line — the [A.S.] terminals represent the Normally Closed Tamper contacts of the device Panel Input exp.

  • Page 29: Connecting The Telephone Line

    Connecting the Telephone Line The KYO300 is powered from the Mains (230V/50 Hz) through a Switching power supply, located inside the In order to allow use of the Dialler, Digital communicator cabinet. The cabinet can also house a backup battery and Teleservice facilities, the telephone line must be (not included) for power backup during Mains failure.

  • Page 30: Connecting The Mains

    Ø end of the Warning power trouble event; 00:00 01/01/2000 Ø Off status of the G indicator on Keypads. DDDDDDDD n Connecting the Mains Connect the jumper 21 (M) to enable the RAM battery. Work carefully through the following steps (refer to “Parts Identification”).

  • Page 31: Thermal Probe

    ONLY use 3 V GLD CR2032 Lithium batteries or 3. Using the graph in Figure 26 and/or Table 3, find similar, there serious risk the value (in accordance with the battery tempera - EXPLOSION if other types are used. When dis - ture) that the Switching Power supply output volt - posing of used batteries follow the instructions age will be based on.

  • Page 32: Programming

    The programmed parameters can be saved on using the KYO300-KYO100 downloading software hard or floppy disk, and downloaded to the Control from the Bentel Security Suite Software package (ac - panel via modem or on-site. The programmed pa - cessory item).

  • Page 33: Keypads Page

    ü The devices connected to the BPI Bus must be Se - For information regarding the ü, No. and Descrip- lected, otherwise the system will be unable to enrol tion parameters, refer to the “Configuration” sec- them. tion. The Select button (on the bottom of the page) will Enabled on Partitions Select the Keypad Partitions.

  • Page 34: Led Keypads

    the first eight characters on the second line of the dis - Arming configurations (refer to the following paragraphs). play correspond to Partitions 1 through 8. If you are programming Monitoring Readers: select the Events to be monitored (refer to the following paragraphs). The Partitions must be selected in successive or- RED spot This row will allow you to assign (ü) the der, therefore, if Partition no.

  • Page 35: Power Sta

    n Power sta Low Battery (below 11.4 V — refer to “Static Test” The Power stations page will allow you to setup the under “Connecting Power supplies” in the “IN - system Power Stations. STALLATION” section) will be signalled by: Ø...

  • Page 36: Accessories

    Disconnected Power supply module will be signalled Receiver Trouble and Lost BPI devices will be sig- nalled in the same way ( X above the s icon on Ø the Switching not connected on Power station the Keypad. If the signal is due to Receiver Trou- event (refer to “Events-Actions”...

  • Page 37: Hardwired Zones

    Auxiliary Communicator The KYO 300 (only) will en - The system cannot generate an Alarm event until the Par - rol the Auxiliary Communicator as soon as it is con - titions the Zone is assigned to Arm (refer to “Partitions”). nected to the Keybus.

  • Page 38: Type

    The chart on the left side of the BPI Zones page shows Instant Violation (refer to “Balance”, “Voltage Range” the available hardwired Zones (refer to “Configuration”). and “Sensitivity”) of an Instant Zone — that is not The following information will be shown for each Zone. Unbypassed or in Test status (refer to “Attributes”);...

  • Page 39: Command

    Exit delay Violation of an Exit delay Zone — during Moreover, the Keypad: the Exit Time of its Partition — will not trigger any Ø WILL NOT signal Alarms triggered by Duress Zones events. In all other cases, the system will generate the (the a indicator WILL NOT blink).

  • Page 40: Attributes

    Autobypass with Reset Unbypass Zones with this If the Partition of the Zone is Disarmed, the Ex- attribute will be bypassed automatically, if violation oc - tended not Ready-to-Arm partition event will ter- curs when their Partitions are Armed. They will be minate when ALL the trigger events terminate unbypassed when standby is restored.

  • Page 41: Threshold

    10K If you apply this Balance Type, the Control panel age on its terminal is below the programmed Standby will consider the Zone in standby status, when the 10 K threshold. resistor (10,000 ohm) is connected between the Zone terminal and Negative. If a 10K Zone shorts to Nega - Alarm If you enable this option, the Control panel will tive, the Control panel will detect Tamper conditions consider the Zone in Alarm status when the voltage on...

  • Page 42: Cycles

    The Inactivity field will allow you to set the Inactivity pa - Ø If 0 is selected, the Zone will be unable to trigger rameters, as follows: Zone Alarm events; Ø if any number other than 0 is selected, the Zone will None If you enable this option, Zone Inactivity will not be able to trigger the corresponding number of Alarm be signalled.

  • Page 43: Voice Messages

    If you set more than 1 Pulse, you will be able to set the Standby This field will allow you to select the Message Within time (i.e. the interval within which the pro - which will be played when the Zone is in Standby sta - grammed number of Pulses must occur), and select tus.

  • Page 44: Wireless

    within the programmed Window, the system will refresh When a Wireless Detector (assigned to a Wireless the window and restore to Standby. Zone) detects Alarm conditions, the system will gener - ate the respective Alarm on zone no. - Wireless event, After generating a Zone Group Alarm, the system will and other events which depend on the programmed be unable to generate further Alarm cycles until ALL the...

  • Page 45: Replacing Wireless Devices

    Control panel Outputs no. 1, no. 2 and no. 3 (no. 1 and ceiver will trigger the Lost wireless zone event as soon no. 2 for KYO 100) are 3 A double switching relays. The ter- as the programmed Supervisory time expires (refer to minals for these Outputs are: the Time supervision zones under “Accessories”...

  • Page 46: Type

    The Expander Outputs are 0.15 A Open-Collectors. Ter. This field shows the Output terminal tag: The terminals for these Outputs are OC1, OC2, OC3, OC4, OC5 and OC6. Ø RL1 = +N1, +A1, C1-NC1-NA1 Ø RL2 = +N2, +A2, C2-NC2-NA2 Ø...

  • Page 47: Attributes

    Normally Closed The electrical state during standby Supervised If the system has been duly set up, this At - is: Positive signal (13.8V) on the [+N] terminals; [+A] tribute will allow the system to monitor the Output for terminals open; [C] terminals closed to their respective short circuits and interrupted connections (refer to terminals [NC];...

  • Page 48: Oscillation

    ON Time This is the maximum activation time of the This field will allow you to set the number of Output Output. Cycles, as follows. Valid entries: Ø 0.2 through 25.4 seconds, in 0.2-second steps (for The parameters in the Cycles section can be set for sec.
  • Page 49 Description This field is for the Partition Label (16 This programming field will allow you to set the Negli - characters). The Description will identify the Partition gence Time. If the system is not Armed within the pro - in all the operations it is involved in. grammed time, the Control panel will generate the Neg - ligence on Partition event.

  • Page 50: Telephone

    Autoreset on Arming If this option is enabled (at de - The comma can be used to insert pauses, for example, fault), the system will Reset Partition Alarms each between a switchboard number and a telephone number. time it is Armed (refer to “Reset Partition Alarms” under “Keypad Codes —...

  • Page 51: Answering Machine

    n Answering Machine Ø turning ON the G LED; The Answering Machine function will allow you to re - Ø generating the Line Trouble signal — an X (blinking) cord a Voice Answer Message. The message will be above the i icon; played each time the Control Panel answers a call after Ø...

  • Page 52: Dialler Book

    signal via Telephone the start and/or end of their asso - The ID numbers can be entered in any order. How- ciated Events. ever, the sequence defined in the Dialler phonebook will determine the call priority. Each Dialler Action can send a Voice Message to a maximum of 32 Telephone numbers.

  • Page 53: Messages

    The Delay applies to the Timeout option (under If this option is enabled, you should include a re- Send Message After ...). quest for the feed back signal (press star) in the message. Valid entries: 1 through 255 seconds, in 1-second steps Default settings: 5 seconds Attempts This field will allow you to program the maxi- mum number of call attempts the Dialler will make be-...

  • Page 54: Digital Communicator

    All If this option is enabled, the Control Panel will call The layout of the Digital Communicator page is as fol - all the Telephone numbers for the corresponding Ac - lows. tion. If this option is disabled (at default). The Dialler will no.

  • Page 55: Actions

    Valid entries: 1 through 99 Reporting formats with the Voice feature transmit Default setting: 3 ONLY one event per call. 2-way audio This option will allow you to program the Reporting formats with the Voice feature should only be 2-way audio session time. used when absolutely necessary.

  • Page 56: Auxiliary Communicator (Kyo 300 Only)

    cator K3-AuxCom” in the “APPENDIX”). Contact ID Event Codes must comprise 2 digits. If The Auxiliary Communicator can send a different Cus - you enter one digit only, the application will auto- tomer Code and Event Code to up to 8 Telephone Num - matically add the letter A ( e.g.

  • Page 57: Voice Messages

    ranges from 2 minutes 8 seconds for high sound quality, With quality Select the Voice Message quality. to 8 minutes 33 seconds for low sound quality (refer to “K3-VOX Voice board” in the “APPENDIX”). n Compound Messages The Control panel Dialler can manage Compound Mes - sages.

  • Page 58: Teleservice

    thorization), or by the User (if the Control panel has The application will assign the first four Telephone been setup to perform the automatic Test Event). Numbers in the General book (Telephone page) to the Teleservice facility. If you do not wish to use When the Control Panel generates a Teleservice call the preset numbers, Disable the corresponding (manually, by User request, or automatically via the...

  • Page 59: Installer Maintenance

    The Trouble signal generated by the Installer Mainte - If the Enable Test Event is Disabled, the Control nance Request and Installer Maintenance will termi - panel will not send the Test call. nate when: Ø the Teleservice page is downloaded; Enable Test Event If this option is Enabled, the Con- Ø...

  • Page 60: Logger - Events Setup

    Ø the Teleservice page is downloaded; The events shown depend on the selected detail Ø the Date and Time of Monitoring Maintenance are level (see “Events Details”). programmed at the Keypad (refer to “Teleservice” in the KEYPAD PROGRAMMING MANUAL). Output The ON column is for the ID number of the Out- put that must activate when the Event in question oc- You must Enable the Central Station Maintenance curs (refer to No.

  • Page 61: Colours

    Ø Fire alarm on partition *Global* The IMQ-SECURITY SYSTEM Approval applies Ø 24h alarm on partition *Global* only when Telephone actions associated with Ø Burglar alarm on partition *Global* Panic events (e.g. “Alarm zone no.” events with the Ø Generic alarm on partition *Global* Panic attribute;...

  • Page 62: Clear

    Ø Block keypad *Global* Ø FAP Key: ONLY the events concerning the specified Ø Recognized user code on Keypad *Global* SuperKey will be viewable (the SuperKey Number must be entered in the small box). FAP Key If you Enable this option, the Super Key events Ø...
  • Page 63 Radio 0624 Table 5 Zone Events — The Event numbers for KYO 100 are those in brackets (..) 10The conditions that trigger Alarm and Tamper status on Hardwired Zones depend on the settings programmed 10The conditions that trigger Alarm and Tamper status on Hardwired Zones depend on the settings programmed on the BPI Zones page.
  • Page 64 ...the Generic+Tamper alarm on parti - (0449- partition no. tion no. event is triggered during Stay tion no. event ends 0464) mode 0880 Table 6 Partition Events — The Event numbers for KYO 100 are those in brackets (..). KYO 300-KYO100 PROGRAMMING...
  • Page 65 Address trips panders have the same BPI bus address Table 7 Control panel events — The Event numbers for KYO 100 are those in brackets (..) 12The conditions that will trigger Tamper on Supervised Outputs are described in the “Outputs” paragraph.
  • Page 66 ..ALL Power Supply Stations respond to (0486) stations not respond to the Control Panel the Control Panel Table 8 Generic Events (continued on next page) — The Event numbers for KYO 100 are those in brackets (..) KYO 300-KYO100 PROGRAMMING...
  • Page 67 Power station Table 8 Generic Events (continued on next page) The Event numbers for KYO 100 are those in brackets (..) 14If the Power station is not equipped with a Thermal probe, the preset output voltage will be 13.8 V. If the Power 14If the Power station is not equipped with a Thermal probe, the preset output voltage will be 13.8 V.
  • Page 68 Date and Time for Central station main - tenance section on the Teleservice page tenance are programmed from a Keypad Table 8 Generic Events — The Event numbers for KYO 100 are those in brackets (..) KYO 300-KYO100 PROGRAMMING...
  • Page 69 Arming of the Partition 1196 1197 Memory alarm ...the Generic alarm on partition no..the Partition Resets (0643- on partition no. Event occurs 0658) 1228 Table 8 Generic Events — The Event numbers for KYO 100 are those in brackets (..)
  • Page 70 ...Wireless Zone no. is violated ...Wireless Zone no. returns to standby zone no. – Via 2548 Radio Table 8 Generic Events — The Event numbers for KYO 100 are those in brackets (..) EVENT STARTS WHEN... ENDS WHEN... 2549 Test ..the Control panel clock signals the Time...
  • Page 71 Table 9 Spot Events (continued ...) — The Event numbers for KYO 100 are those in brackets (..) 15The Kissoff tone is the signal the receiver uses to communicate reception of a data block 15The Kissoff tone is the signal the receiver uses to communicate reception of a data block...
  • Page 72 Teleservice call fails Table 9 Spot Events — The Event numbers for KYO 100 are those in brackets (..) Event 1 Enter the ID Number of the first event (associ - cur. If these events do not occur within the pro -...
  • Page 73 Power station, Battery low memory, Telephone line trouble 3392 Memo present … a message is recorded on the ..the message is played (2036) Answerphone Table 11 Special Events — The Event numbers for KYO 100 are those in brackets (..)
  • Page 74 If you apply the OR Operator to two NON-Spot If you apply the OR operator to a Spot Event and a Events, the Window will be uninfluential. NON-Spot event, the Customized Event may in some cases operate as a Spot Event (i.e. end al- Ø...
  • Page 75 the Spot Event ends, and no other NON-Spot Events Ø Event 1 and Event 2 NON-Spot, WITH Window have occurred in the meantime (Fig. 42: c6). The system will generate the Customized Event when Ø Event 1 and Event 2 Spot, NO Window (NOT the status of Event 1 is different from that of Event 2 ALLOWED) within the Window (see Fig.
  • Page 76 d4, d7 and d9). If you apply the XOR operator to a NON-Spot event The Customized Event will end when the status of the and a Spot Event, the Customized event may, in Event 1 is the same as that of Event 2 (see Fig. 48: d2, some cases, operate as a Spot Event (i.e.

  • Page 77: Scheduler - Arming

    When calculating the XOR result of two Spot Events, n Models you must consider them as both ending when the Win - The Models button will open the programming window dow expires. In this way, the Customized Event will start of the parameters described in this section.

  • Page 78: Options

    For example, the Christmas Holiday Model is applied Valid entries: 0 through 60 minutes, in 1-minute steps. once a year, therefore, it will take priority over the Ø If you enter a value of over 60 minutes, it will be recti - Weekday Model that is applied 5 days per week.

  • Page 79: Scheduler - Timers

    4 different ON and 4 different OFF Times for each of 1st OFF / 2nd OFF / 3rd OFF / 4th OFF This field will the 64 (32 for KYO 100) Control panel Timers. allow you to set the OFF Time (refer to 1st Dis. / 2nd Dis.

  • Page 80: Models

    n Models Lock Installer Code If this option is enabled, restoral Refer to “Models” and “Events” under “Scheduler - of the default settings WILL NOT default the PIN of Timers”. Code no. 200 (MASTER Installer Code). Disable Arming with Partition Alarm If this option is Options enabled, Arm commands from Keypads or Readers will not be carried out if the system detects Partitions in...
  • Page 81 Ø If key 5 is pressed, the Control panel will play mes- The above-mentioned “Display … on Keypad” op- sage 59 which contains the instructions for the DTMF tions will soon be available for programming via menu Arm/Disarm single Partitions options, that is, the Keypad.

  • Page 82: Keypad Codes - User

    The Code list (195 Codes for KYO 300; 97 Codes for Default: 3 minutes KYO 100), on the left side of the Users page, shows the following information for each Code. Mains Fault Timeout This field will allow you to set the No.

  • Page 83: Enable On Partitions

    D As for A but for D Mode Arm commands at a Keypad. phone Access Codes) CANNOT be Father codes For KYO 100 — Codes no. 82 to 97 (the 16 Tele - n Associated Timer phone Access Codes) CANNOT be Father codes.

  • Page 84: User Menu Access

    A Code that DOES NOT HAVE Always status the code concerned on the LCD Keypads (16 keypads (Always option disabled) can be its own Father for KYO 100 and 32 for KYO 300). code, in which case, the Always attribute will be enabled automatically.

  • Page 85: Lost Installer Codes

    For the instructions on how to restore the default PIN 0200 The Installer Code can program and change all pa- for KYO 300, or 0100 for KYO 100, refer to the “Restore De - rameters via computer. fault Settings” paragraph.

  • Page 86: User Codes

    n User Codes Enab./Disab. Scheduler If this option is enabled, the This paragraph provides a general description of the Code will be able to Enable/Disable the Scheduler on its User Code functions — refer to the USER’S MANUAL Partitions. for further information. Enab./Disab.

  • Page 87: Installer Codes

    Play/Rec. Memo If this option is enabled, the Code will If the Alarm conditions are still present after Reset be able to listen to and record Voice Memos at the Key - (approx. 2 seconds), the Control panel will trigger pad.

  • Page 88: Digital Keys

    Change Installer PIN If this option is enabled, the To ENABLE the Key on all the Partitions: click the Code will be able to change its own PIN, and the PINs of Partitions button (bottom of page) then select All. its assigned codes (sons).

  • Page 89: Clock

    Clock 1. Connect the Control Panel serial port (24) to one of the PC serial ports, as follows: Proper functioning of the Scheduler/Timers depends on – using a CVSER/9F9F link (accessory item), or a the Clock setting (Clock page), therefore, the Control cable similar to the one in Figure 53a, connect the panel clock must be set with extreme precision.

  • Page 90: Remote Downloading

    Configuration from the Folders to/from the connected Control panel. menu; to download All the Pages, select KYO 300 (or KYO 100) from the Folders menu. 7. To program and view the parameters of the con- nected Control panel, work carefully through steps 6.
  • Page 91 This is the release of the Modem that MODEM v. x.xx is connected to the PC serial port The application cannot find the Bmod Modem not on the specified serial port. recognized Check the cable and serial port settings The Modem/PC system is waiting for an incoming call.

  • Page 92: Appendix

    APPENDIX K3-VOX Voice Board 2. Join the two parts then twist to lock in place. Disconnect the Mains and battery power before 3. Screw the Speaker onto the backplate. starting the installation procedure. 4. Plug the Voice board into the connector 17, secure The K3-VOX Voice board records and plays Voice it firmly in position by means of the screws.

  • Page 93: Manual Selection

    Terminals [M], [SP+], [SP-] and [MIC], on the For example, if the Output-expander is assigned to Ad - Alison-DV, must be connected to the Voice dress no. 01, its hardware Outputs OC1, OC2, OC3 and Board by a separate cable to the one used for OC4 will correspond to software Outputs 7, 8, 9 and 10.

  • Page 94: Manual And Auto-Select Mode

    n Manual and Auto-select mode — Specific events printout (refer to “ Logger — Events Manual and Auto-select Listen-in can be integrated. Setup” under “Programming”). This will allow the User to select (manually) specific lo - cations during standby status. n Identification of Parts The following Table describes the parts illustrated in Use 4 Outputs for Manual-select Listen-in mode, and 4...

  • Page 95: K3-Auxcom Auxiliary Communicator

    3. Connect the Printer lead to the connector 119 on The K3-AuxCom cannot function when jumpers 18 the Printer Interface. and 48 are inserted. If you disconnect the K3-AuxCom, you must RE-INSERT jumpers 18 and 48, otherwise, the Con- K3-AuxCom Auxiliary Communicator trol panel will be isolated from the Telephone line.

  • Page 96: Choosing A Mounting Location

    128 Spring Catch n Connecting the Receiver 129 Terminal board Connect the Receiver terminal 25 to the Interface termi - nal 15 (as shown in Figure 61). n Choosing a Mounting Location Use Shielded cable for the connection: connect Mount the Receiver and Wireless Devices after the one end of the shield to terminal BLK on the Inter- placement tests.

  • Page 97: Reporting Formats

    1. Remove all power from the Control panel (Mains Ø Event Code (CODE column): identifies the event and battery). (Event Codes can be changed, refer to “Actions” un - der “Digital Communicator” in the “PROGRAMMING” 2. Remove the jumper 21 (M). section);...
  • Page 98 Timer Description Customized Events 64, 65 16 character labels can be assigned to each Timer. This feature allows the system to manage up to 32 Cus - tomized events. Each Customized Event will be gener - Power Station Management 7, 19, 34, 66, 98 ated by the combined effect of two other events The Control panel Bus accepts up to 8 x 2 A and/or 5 A (selected as required) that must occur within a pro -...
  • Page 99 EVENT CONTACT ID CL. CODE GROUP ZONE TYPE Warning BPI input expander ET/ER 0000 Warning keypads ET/ER 0000 Warning output expanders ET/ER 0000 Warning power stations ET/ER 0000 Warning wireless device ET/ER 0000 False key DD/DR 0000 Warning fuse +F YP/YQ 0000 Warning fuse +F1...
  • Page 100 EVENT CONTACT ID CL. CODE GROUP ZONE TYPE Exit time on partition part. no. UX/UX part. no. Entry time on partition part. no. UX/UX part. no. Autoarming warning partition part. no. UX/UX part. no. Memory alarm on partition part. no. BA/BR part.

  • Page 101: Differences Between Kyo 300 And Kyo

    Speaker) which can be connected to the K3-VOX Voice Board. LED Keypad System supports the new Alison/32LP LED Keypads n KYO 300 Rev. 1.20 and KYO 100 Rev. 1.20 Zone in AND Mode option Enable/Disable Voice menu This option will allow the system to generate Alarms...

This manual is also suitable for:

Kyo 300

Table of Contents