Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for AGP SP2500
Summary of Contents for AGP SP2500
- Page 1 Warning: Only tools equipped with over load protection, when motor has been cut off due to over load, always switch on machine with no load for at least 3 minutes to reduce temperature before switch on again to avoid burn out to the motor. Version:20140822...
- Page 2 Spindle Motor Brush Cap Lock Button Trigger Switch Main Handle Speed Control Thumbwheel Power Input 900W Voltage See machine nameplate No Load min 900-2500 Spindle Max. Recommended Pad Diameter 180mm (7") Net Weight 2.0 kg (4.4 lbs)
-
Page 3: General Safety Instructions
GENERAL SAFETY INSTRUCTIONS When operating a power tool outdoors, use an extension cord suitable for outdoor use. WARNING! Read all safety warnings and Use of a cord suitable for outdoor use reduces all instructions. Failure to follow the the risk of electric shock. I f o p e rat i n g a p owe r to o l i n a d a m p warnings and instructions may result in location is unavoidable, use an ear th... - Page 4 5) SERVICE ensure these are connected and properly used. Use of dust collection can reduce dust-related Have your power tool serviced by a qualified hazards. repair person using only identical replacement parts. This will ensure that the safety of the power 4) POWER TOOL USE AND CARE tool is maintained.
-
Page 5: Safety Warnings Common For Sanding Or Polishing Operations
SAFETY WARNINGS COMMON FOR i n s p e c t fo r d a m a g e o r i n s t a l l a n SANDING OR POLISHING OPERATIONS undamaged accessory. After inspecting and installing an accessory, position This power tool is intended to function as yourself and bystanders away from the a sander or polisher. -
Page 6: Further Safety Instructions For All Operations
to resist kickback forces. Always use contact with the spinning accessory could snag your clothing, pulling the accessory into auxiliar y handle, if provided, for your body. maximum control over kickback or 14. Regularly clean the power tool’s air vents. torque reaction during start-up. -
Page 7: Specific Safety Rules
c a n e n t a n g l e yo u r f i n g e r s o r s n a g o n t h e dust. Allowing dust to get into your mouth or workpiece. - Page 8 OPERATION with the suffix WA or W following the cord type designation. For example – SJTW-A to indicate it is TO START AND STOP THE MACHINE acceptable for outdoor use. Always choose the shortest possible cord. CAUTION: Make sure switch is OFF and power circuit voltage is the same as that shown on the FOREWORD specification plate.
-
Page 9: Maintenance
POLISHING OPERATION FAILURE TO START WARNING: If the item to be polished is not Should your tool fail to start, check to make sure attached to anything and is light enough to be the prongs on the cord plug are making good moved by the spinning polishing pad, it should contact in the outlet. - Page 10 NOTE: To reinstall the same brushes, first make sure the brushes go back in the way they came out. Otherwise a break-in period will occur that will reduce motor performance and increase brush wear. I f t he re pl ace me nt of t he p owe r su pp ly cord is necessary, this has to be done by the manufacturer or their agent in order to avoid a safety hazard.
- Page 11 WIRING...
-
Page 12: Exploded View
EXPLODED VIEW... -
Page 13: Parts List
PARTS LIST Parts Name Q'ty SPINDLE M16 x P2.0 PARALLEL KEY 3 x 3 x 10 SCREW M5 x 30 GEAR CASE SIDE HANDLE BEARING 6201-2RS SPACER Ø11.6 x Ø17 x 5 BEARING PLATE SCREW M4 x 8 OUTPUT GEAR M1.0 x 37T EXTERNAL SNAP RING S-10...
Need help?
Do you have a question about the SP2500 and is the answer not in the manual?
Questions and answers