Download Print this page

ETC Unison Echo Setup Manual

Rack mount station power supply w/ aux power

Advertisement

Quick Links

ETC Setup Guide
Unison Echo™ Rack Mount Station Power Supply w/ Aux Power
Overview
The Echo Rack Mount Station Power Supply with Auxiliary Power (E-SPM-RM-A) is designed for use with
the Echo control system to supply bus power for up to 16 Echo architectural control stations on the
topology-free EchoConnect control network and provides 24 Vdc auxiliary power (maximum 36 watts) for
Echo devices. The E-SPM-RM-A also supports connection of up to 16 compatible power panels or
distributed power controllers over EchoConnect.
Note:
For use with ETC Dimming and Relay Products.
Installation
Install Unit in Equipment Rack
The E-SPM-RM-A utilizes 2U of rack space.
Step 1:
Step 2:

Power and Control Wiring

The rack mount enclosure is provided with wiring connections on the rear of the unit.
• AC Power
• EchoConnect (Station Bus) and ESD Ground
• 24 Vdc Auxiliary power
Corporate Headquarters
London, UK
Tel +44 (0)20 8896 1000
Rome, IT
Tel +39 (06) 32 111 683
Holzkirchen, DE
Hong Kong
Tel +852 2799 1220
Web:
www.etcconnect.com
7186M2202
Rev A
Rack Mount Station Power Supply with Auxiliary
If you are using Cat5 (or Cat5e) wiring, an external Echo Cat5 Termination Tray is
required. Contact ETC for ordering details. Control wiring instructions between the
termination tray and this Rack Mount Station Power Supply with Auxiliary will be
provided with the Unison EchoConnect Cat5 Termination Tray installation instructions.
Locate the included rack mounting hardware kit including the mounting screws and
washers.
Use the hardware provided to mount the unit to the mounting rails in your equipment rack.
Middleton, WI, USA
Tel +608 831 4116
Service: (UK)
Service: (UK)
service@etceurope.com
Tel +49 (80 24) 47 00-0
Service: (DE)
Service: (Asia)
service@etcasia.com
© 2015 ETC. All Rights Reserved.
Released 2015-06
ETC intends this document to be provided in its entirety.
Service: (Americas)
service@etceurope.com
techserv-hoki@etcconnect.com
Product information and specifications subject to change.
Page 1 of 3
service@etcconnect.com
Electronic Theatre Controls, Inc.

Advertisement

loading

Summary of Contents for ETC Unison Echo

  • Page 1: Power And Control Wiring

    ETC Setup Guide Unison Echo™ Rack Mount Station Power Supply w/ Aux Power Overview The Echo Rack Mount Station Power Supply with Auxiliary Power (E-SPM-RM-A) is designed for use with the Echo control system to supply bus power for up to 16 Echo architectural control stations on the topology-free EchoConnect control network and provides 24 Vdc auxiliary power (maximum 36 watts) for Echo devices.
  • Page 2 E-SPM-RM-A to provide power for up to 16 Echo sensors and stations and allows for up to 16 power controllers. EchoConnect is a bidirectional protocol that uses one pair of wires (data+ and data-) for both data and power. ETC recommends using Belden 8471 (or approved equal) Class II wire. Note: The total combined length of an EchoConnect wire run (using Belden 8471, or equal) may not exceed 1,640 feet (500m).
  • Page 3: Status Indicators

    ETC Setup Guide Rack Mount Station Power Supply with Auxiliary Final Installation Step 1: Plug the IEC power cable into the power source. Step 2: Secure all cables to the enclosure using cable ties (not provided). Four mounts are provided on the rear panel of the unit.