Electrolyser for disinfection of the swimming pool water (21 pages)
Summary of Contents for Aseko ASIN AQUA Home
Page 1
USER MANUAL Home ASIN AQUA ® CUTTING EDGE TECHNOLOGY for crystal clear and healthy pool water www.aseko.com...
Page 2
General safety information This user manual contain basic information that should be observed during assembly, start-up, operation, and maintenance. Therefore, this user manual must be read by installers and operators prior to assembly and start/up, and must be accessible to every user of this unit. Additionally, all further safety information in this document absolutely must be observed.
Page 3
The chemicals used with the ASIN Aqua must be handled in a safe manner to prevent damage or personal harm. Aseko recommends you always use personal protective safety equipment when handling the pH and chlorine agents. Refer to the Materials Safety Data Sheet (MSDS).
Page 4
What do you receive in your box Device ASIN AQUA Home Probe housing 2 pcs #12013 Peristaltic pumps #12093 Flowmeter #12106 Water thermometer with housing #12010 Measured water filter #12090 Long Life pH Probe #12012 CLF* probe #12052 Redox Long Life* probe #12016...
Page 5
ZPM Coagulation mixer #30001 Inserting DN50 plug pH 7.00 Buffer #12065 Air thermometer #8953 1/4” threaded #12134 Redox Buffer #12063 ASEKO original chemical solution 20 l volume for pools CHLORPURE #12075 pH MINUS #12130 ALGICID #12156 FLOC+C #12139 5 l volume for whirlpools...
ASIN AQUA Home is adjustable to dose pH MINUS or pH PLUS. Treatment for stabilizing of pool water acidity at the optimum level. Precise measuring by pH probe combined with the system digital intelligence controls the preset pH level of the circulating pool water in all pool operation modes and variable environment conditions.
The system must be equipped by optional air thermometer #8953. Control by External touch display Some functions of ASIN AQUA Home can be monitored and controled by external touch display. System must be equipped by optional External touch display #12048.
Page 8
User friendly and sophysticated graphic enables easy selection of items to be monitored and preset the value limits to send alerts at your smartphone. ASIN AQUA Home will automatically generate alert to your smartphone if any of selected items exceed the individually preset limits or in case any system failure so you can call for action to keep your pool in condition if necessary.
Enhancement of filtering efficiency activated filter media ® AFM is direct substitute for filter sand. It doubles efficiency of the existing filtration system. AFM is resistant to biological pollution and formation of ® so-called bio-film. coagulation mixer ® ZPM increases effects of coagulation and flocculation for transition of smaller dissolved solids (turbidity) to larger particles that can be removed by filtering.
ASIN AQUA Home Installation ASIN AQUA Home is to be wall mounted in dry and dust-free environment with temperature ranging from +5 °C to +40 °C. Install the mounting rail, which serves for attachment, to the wall. Select location so that free space 40 °C...
Installing the Probes Carefully insert the pH, CLF or REDOX probe into the housing. Wrench socket for Hand tighten or use the attached plastic wrench socket for probes. probes #13046 Connect the connector and lock it by tightening a connector ring. After probes have been inserted, slightly tightened and connectors have been connected, ASIN AQUA Home is ready for connection to the water system of your pool.
Pool Water Connection Water valve CONNECTION The pool water to be measured must be connected to ASIN AQUA Home. fitting Connect the measured water inlet downstream of the pump, upstream of the filter and ZPM (coagulation mixer). Place the water valve fitting to the T-joint, blinded by DN50 G1/4” threaded G1/4”...
Page 13
POOL WATER OUTLET POOL WATER POOL WATER INLET INLET Thermometer THE WATER OUTLET CAN BE (Zeta REALISED: Potential Mixer) 1. downstream of filtration 2. to non-pressure (overflow tank) 3. upstream of filter pump Waste Besgo FROM POOL TO POOL Heating...
Page 14
Pool Chemicals Connection At this step is necessary to connect the injecting valves of individual chemicals to the dosing pumps and dosed agents. Place the injecting valve in the T-joint, blinded with the DN50 G1/4” threaded plug #12134. Cut the PE tube at 90 ° angle to ensure proper fitting. •...
Page 15
Thermometer (Zeta Potential Mixer) Waste Besgo FROM POOL TO POOL Heating...
Page 16
Accessories Connection POWER SUPPLY 230 V ~ 50 Hz T125mA Besgo valve connector 19 Besgo valve 18 Refilling solenoid Refilling solenoid connector 17 Heating relay Heating relay T800mA Roller shutter Connected - closed position Disconnected - opened Water level Water level senzor sensor connector Flowmeter...
Page 17
VS Pump Module Connection Variable speed pump module (*optional) #00000 Standard configuration of the jumper for SPECK VS Pump. SPECK Jumper settings VS MODULE PUMP for SPECK jumper NO jumper jumper STOP STOP Jumper configuration STOP for other pumps. PENTAIR Jumper settings VS MODULE PUMP...
Page 18
Connect the filtering device to the ASIN AQUA Home switched socket outlet (filtration power supply - max. 1.4 kW / 230 VAC). Connect the 230 V / 50 Hz mains cable to ASIN AQUA Home (on the right Residual Proudový...
Page 19
Press DO NOT FORGET! Provide the testing run and stop of all accessories connected to ASIN AQUA Home. At this step just test, do not dose the aids or provide the initial dose of chemicals! Press to switch ON (GREEN) 2nd press to switch OFF If bubbles occur here, the pump draws air in.
Page 20
Touch screen description Basic Screen The basic screen display measured, required values and status information. E.g. click on the Chlorine tab to enter the setting of the required chlorine value in pool water. Required Value. Measured Value. The chlorine pump status – ON. ON indicates the ON - filtering follows Enter settings.
Page 21
Settings Back to the main screen. Displays help/manual for Back to the previous the particular screen. screen. Movement through Menu Movement in menu to the previous page. ON - function is switched on Indicator of the current page and the total number of pages.
Page 22
To ensure the correct function of timers, set the current date and time. Pool Volume To ensure the correct function of ASIN AQUA Home, enter the correct volume of your. Calculate your pool volume in m Length (L) times width (W) times depth (D) is volume (V) - (L × W × D = V).
Page 23
#12010. • After the freeze protection has been enabled, ASIN AQUA Home checks outdoor temperature. If outdoor temperature is lower than 0 °C, filtration is switched on to circulate the pool water. After 15 minutes will ASIN AQUA Home measure temperature of the pool water.
4 to 10 min, at SPA 1 to 10 min. Delay time after start (upon timer switching on) is time after start for which ASIN AQUA Home does not take any action and it waits for stabilization of a signal from probes.
Page 25
Choosing the disinfection probe CLF free chlorine probe Free chlorine measurement, CHLOR PURE dosing Redox probe of the RX potential Measurement of redox potential, CHLOR PURE dosing DOSE ml/m time dose per hour or per day Without a probe, CHLOR PURE time dosing No need of probe It is recommended to use this function only as “EMERGENCY MODE”...
Page 26
Setting Considering that the ASIN AQUA Home water treatment system is efficient in the broad pH range, it is useful to enter the required pH value equal to pH value of water you refill or slightly lower. Required pH value = refilled water pH value (in the range from 6.8 to 7.5)
Page 27
Set FLOC+C to 10 ml m per day (see the chaper FLOC+C Setting). 2. Close the water supply to the probes ASIN AQUA Home display "No water supply to the probes" notification. 3. Perform superchlorination Perform superchlorination of pool water with Super CHLOR (inorganic active SuperCHLOR chlorine without stabilizers).
Page 28
0.2 mg/l max) (regardless of the required value according to the table). Repeat the measurement after the water in the pool is mixed thoroughly and the required value shown on the ASIN AQUA Home display is settled. Repeat the process until the chlorine concentration in pool water matches the required value then set the correct required value according to the table.
Page 29
If you use the Redox probe For the correct functionality of the REDOX probe, you must observe the following conditions: pH of the pool water The ideal pH value should be between 6.8 and 7.5. The pH of the pool water must be stabilized. If the pH value fluctuates, the value of the Redox changes accordingly.
Page 30
Response If the measured pH value does not change even after preset quantity of doses (according to the settings), ASIN AQUA Home stops pH dosing and an error message appears on the display. The other ASIN AQUA Home functions are not limited.
Page 31
Calibration pH Probe Calibration When pH is being measured in operation, there may be a difference between the ASIN AQUA Home value and the current pH value measured directly in water. Calibration can be done in two ways: With a buffer •...
Page 32
0.3 to 1.2 mg/l, otherwise the calibration cannot be performed. Calibration procedure : Compare the value displayed on the ASIN AQUA Home with the one measured with colorimeter or Pool Tester. If the difference in values is up to 0.2 mg/l, calibration is not necessary...
Page 33
Home, calibrate the thermometer in the water thermometer calibration menu. Air Thermometer Calibration If air temperature is different from temperature shown by ASIN AQUA Home, calibrate the thermometer in the air thermometer calibration menu. Testing the pH probe pH - Buffer 7,00 #12065...
Page 34
LAN cable. Wifi connection If you install the ASIN AQUA Home in place where is no access to your pri- vate network by wired connection but your Wifi has enough signal, you can connect the ASIN AQUA Home to your Wifi by use of Wifi extender.
Page 35
INTERNET Home network INTERNET 3G / LTE WIFI EXTENDER Wifi extender INTERNET Powerline via 230 V 230 V socket outlet INTERNET...
Page 36
After you connect the ASIN AQUA Home to the internet download the iPool Live application to your smartphone. Application is available for iOS and Android operation systems.
Page 37
The web application for detailed monitoring of the pool water quality by means of well-arranged graphs. It shows all the measured parameters as well as ASIN AQUA Home actions up to 30 days back. This application is giving you the detailed information of the pool status and detailed review of all events, taken actions and act levels of monitored items up to 30 days back.
Page 38
In case of public pools, replace #12005 every year. #12014 pH probe pH Probe Maintenance Take the pH probe out of ASIN AQUA Home housing and clean it from impurities. Follow the instructions attached to the used probe.
Page 39
Too Rapid pH Change Too rapid change of pH is usually caused by refilling water directly to the skimmer. If such rapid change of pH occur, ASIN AQUA Home stops controlling pH for two hours. This limitation can be manually disabled.
Need help?
Do you have a question about the ASIN AQUA Home and is the answer not in the manual?
Questions and answers