Table of Contents
Advertisement
Quick Links
Contents
Installation Quick Start ················································································································································· 1
Preparing for installation ·················································································································································· 1
ESD prevention ························································································································································· 1
Examining the installation site ································································································································· 1
Installation tools and accessories ··························································································································· 2
Installing the router ···························································································································································· 2
Confirming installation preparations ······················································································································ 3
Installing cage nuts ··················································································································································· 3
Installing the cable management bracket and mounting brackets ······································································ 5
Mounting the router in the rack ······························································································································ 6
Grounding the router ··············································································································································· 7
Installing a card ························································································································································ 9
Installing a subcard ··············································································································································· 11
Installing a power module ············································································································································· 12
Verifying the installation ······································································································································· 19
Logging in to the router ················································································································································· 20
Connecting the console cable ······························································································································ 20
Powering on the router ········································································································································· 20
Obtaining documentation ············································································································································· 21
i
Advertisement
Table of Contents
Related Manuals for H3C SR8800-X-S
Summary of Contents for H3C SR8800-X-S
-
Page 1: Table Of Contents
Contents Installation Quick Start ················································································································································· 1 Preparing for installation ·················································································································································· 1 ESD prevention ························································································································································· 1 Examining the installation site ································································································································· 1 Installation tools and accessories ··························································································································· 2 Installing the router ···························································································································································· 2 Confirming installation preparations ······················································································································ 3 ... -
Page 2: Installation Quick Start
Figure 1 Attaching an ESD wrist strap (on an SR8803-X-S) Examining the installation site The SR8800-X-S routers can only be used indoors. To make sure the router operates correctly and to prolong its service lifetime, the installation site must meet the load-bearing, temperature, humidity, cleanness, EMI, grounding, power, and space requirements. -
Page 3: Installation Tools And Accessories
Installation tools and accessories This section only lists the most commonly used installation accessories and tools. Figure 2 Installation tools and accessories Installing the router Figure 3 Installation flow Start Confirm installation preparations Install cage nuts Install mounting brackets and cable management brackets Mount the router to the rack Ground the router... -
Page 4: Confirming Installation Preparations
Confirming installation preparations H3C recommends that you order the H3C Rack Mounting Kit (LSTM2KSGD0) 500 mm (19.69 in) to 800 mm (31.50 in). For the installation procedures, see the installation guide. Make sure the bottom edge of the slide rail aligns with the middle of the narrower metal area between... - Page 5 Figure 5 Determining installation positions for cage nuts (SR8803-X-S) (1) Cage nuts Figure 6 Installing the cage nut...
-
Page 6: Installing The Cable Management Bracket And Mounting Brackets
Installing the cable management bracket and mounting brackets Before installing the router to the rack, install the cable management bracket and mounting brackets shipped with the router. The cable management bracket is used for cable deployment, and mounting brackets are used for attaching the chassis to the rack. Each router is shipped with two mounting brackets and one cable management bracket. -
Page 7: Mounting The Router In The Rack
Figure 8 Installing the mounting brackets (SR8803-X-S) (1) Screw (2) Left mounting bracket (3) Right mounting bracket Mounting the router in the rack WARNING! • Do not hold the fan tray handle, the power module handle, the back cover of the chassis, or the air vents of the chassis to carry the router. -
Page 8: Grounding The Router
Figure 9 Installing the router in a rack (SR8803-X-S) If the screw holes on the mounting brackets cannot align with the cage nuts on the rack, perform the following verifications: Verify that the bottom edge of the slide rail aligns with the middle of the narrowest metal area •... - Page 9 Figure 10 Connecting the grounding cable to a grounding strip (1) Grounding holes (2) Grounding strip (3) Grounding post (4) Ring terminal (5) Hex nut Grounding the router through the PE wire of an AC power module CAUTION: Make sure the AC power module uses a three-wire cable with a protection wire. •...
-
Page 10: Installing A Card
Figure 11 Grounding the router through the PE wire of the AC power module Grounding the router through the RTN wire of a DC power module CAUTION: Make sure the RTN wire is correctly grounded at the DC egress of the DC power cabinet. You can ground the router through the return (RTN) wire of the DC power module, as shown in Figure when the following conditions exist:... - Page 11 Figure 13 Slot arrangement (for the SR8803-X-S) (1) MPU slots (2) LPU slots Installing MPUs and LPUs CAUTION: Before installing a card to the chassis, make sure the connectors on the card are not broken or blocked to avoid damaging the backplane. IMPORTANT: To ensure good ventilation, install a blank filler panel over an empty MPU or LPU slot.
-
Page 12: Installing A Subcard
Push the ejector levers up to the vertical level. Skip this step for cards except the multi-service base cards. Examine the card status after you power on the router. Figure 14 Installing a card (SR8803-X-S) Installing a subcard This section describes how to install a PIC subcard or an MIC subcard in a base card. Both the PIC and MIC subcards are hot-swappable. -
Page 13: Installing A Power Module
Figure 15 Installing a subcard (1) Loosen the captive screw (2) Rotate out the ejector levers (3) Push in the subcard (4) Rotate in the ejector levers (5) Secure the captive screw Installing a power module WARNING! Provide a circuit breaker for each power module and make sure the circuit breaker is off before •... - Page 14 PWR-SPA power adapter and the PSR650 instead. For more information about the power adapter, see the H3C PWR-SPA Power Module Adapter User Manual. If you select a power adapter, install it to the chassis, and then install a power module to the power adapter.
- Page 15 Figure 16 Installing a power module (PSR1400-D) Connecting power cords WARNING! Before connecting the power cord, make sure the power module is switched off. Table 1 Power cord connection for SR8800-X-S routers Power input Model Description (AC/DC) PSR320-A Connecting power cords for the PSR320-A/PSR650-A...
- Page 16 Connecting power cords for the PSR320-A/PSR650-A Insert the two ends of the bail latch to the holders on the left of the power socket. Then, pull the bail latch to the left. Unpack the power cord, and make sure the power cord model is correct. Both the PSR320-A and PSR650-A use the 10A AC power cord.
- Page 17 Figure 18 Connecting the power cord Connecting power cords for the PSR1400-A Unpack the power cord, and make sure the power cord model is correct. The PSR1400-A uses the 16A AC power cord. Use a Phillips screwdriver to remove the screws from the power cord retainer suite and remove the right part of the retainer suite.
- Page 18 Figure 19 Connecting the power cord for the PSR1400-A (1) Power switch (O: off; —: on) (2) Power module LED (3) Power cord retainer suite (4) Screw (5) AC power cord Connecting power cords for the PSR650-D/PSR650C-12D WARNING! When connecting the DC power cord to the DC wiring terminals, make sure the circuit breaker at the power input end is off.
- Page 19 Figure 20 Connecting the power cord for the PSR650-D (1) Grounding screw (2) DC wiring terminals (3) Screws (4) Protection cover Connecting power cords for the PSR1400-D WARNING! When connecting the DC power cord to the DC wiring terminals, make sure the – end of the circuit breaker at the power input end is off.
-
Page 20: Verifying The Installation
Figure 21 Connecting the power cord for the PSR1400-D (1) Flat washers (2) DC wiring terminal (3) Spring washer (4) M6 nut (5) Protection cover Verifying the installation After the installation is completed, verify the installation against the following list. Be sure that all check results are positive. -
Page 21: Logging In To The Router
Verify that the power cord is connected to the power source. Power on the router. Turn on the circuit breaker. Verify that the switch is operating correctly by observing the LEDs on the switch. For more information about the LEDs, see H3C SR8800-X-S Routers Installation Guide. -
Page 22: Obtaining Documentation
Obtaining documentation To access the most up-to-date H3C product documentation, go to the H3C website at http://www.h3c.com.hk To obtain information about installation, configuration, and maintenance, click http://www.h3c.com.hk/Technical_Documents To obtain software version information such as release notes, click http://www.h3c.com.hk/Software_Download Copyright © 2013-2017, New H3C Technologies Co., Ltd. and its licensors.
Need help?
Do you have a question about the SR8800-X-S and is the answer not in the manual?
Questions and answers