Table of Contents
Advertisement
Quick Links
Designed, Manufactured and Supported in the USA
VIKING
C O M M U N I C A T I O N & S E C U R I T Y S O L U T I O N S
Emergency Phone Panic Button Kit
(for use with Viking Emergency Phones)
The PB-1 Panic Button Kit connects to
a Viking 1600A or 1600-IP Series
Emergency Phone to provide a one-way
talk path to the pre-programmed
number when used.
The PB-1 will activate the 1600A or
1600-IP Series Emergency Phone and
allows the called party to light a red LED
to indicate that the call is connected.
The called party will be able to hear the
Installation site, but the site will not be
able to hear the called party. This makes
Features
• LED to indicate call connected
• One-way talk path for listening
without audible indication
• Unobtrusive - mount anywhere at any
angle with supplied foam tape
• Provides security and peace of mind
• Switch can be used to trigger inputs
on K-2000-DVA, K-202-DVA, SLP-1,
SLP-4, etc.
www.vikingelectronics.com
Information: (715) 386-8861
PRODUCT MANUAL
it a very effective security measure, as
there is no other indication that the site
is being monitored.
Applications
• Courtrooms
• Bank tellers
• Gas stations
• Motel reception desks
• All night restaurants
• Convenience stores
Specifications
Dimensions: 65mm x 35mm x 20mm
(2.56" x 1.38" x 0.79")
Shipping Weight: 0.05kg (0.1 lbs)
Environmental: 0°C to 32°C (32°F to
90°F) with 5% to 95% noncondensing
humidity
Cord Length: 7 ft
Connections: (1) RJ11 jack, (1) 10-
position JST connector, (6) gel-filled butt
connectors
PB-1
Panic Button Kit
August 3, 2017
Advertisement
Table of Contents
Related Manuals for Viking PB-1
Summary of Contents for Viking PB-1
- Page 1 C O M M U N I C A T I O N & S E C U R I T Y S O L U T I O N S Emergency Phone Panic Button Kit (for use with Viking Emergency Phones) The PB-1 Panic Button Kit connects to a Viking 1600A or 1600-IP Series Emergency Phone to provide a one-way talk path to the pre-programmed number when used.
- Page 2 Remove the 1600A Series Emergency Phone board and then remove the Step 4. installed mic by carefully pulling it out of the black plastic mic mount. Place the mic from the PB-1 cable into the mic mount and replace the Step 5. 1600A Series Emergency Phone board.
- Page 3 Step 4. board, leaving at least 1 inch of wire at the connector. Attach the black wire from the board to the black wire from the PB-1 Step 5. using a gel-filled butt connector (do not strip prior to inserting).
- Page 4 Remove the 1600-IP Series Emergency Phone board and then remove Step 4. the installed mic by carefully pulling it out of the black plastic mic mount. Place the mic from the PB-1 cable into the mic mount and replace the Step 5. 1600-IP Series Emergency Phone board.
- Page 5 Step 4. board, leaving at least 1 inch of wire at the connector. Attach the black wire from the board to the black wire from the PB-1 Step 5. using a gel-filled butt connector (do not strip prior to inserting).
- Page 6 E. Switch Only Applications (K-2000-DVA, K-202-DVA, SLP-1 or SLP-4) Step 1. Mount the PB-1 using the supplied foam tape. Step 2. Connect the RJ11 plug on the supplied cable to the PB-1. Cut the PB-1 cable at the white connector, discarding the connector and Step 3.
- Page 7 #00 - #05 Up to 5 emergency speed dial numbers. Play message on answer, dial “Q” to stop 000210 message and light LED on PB-1. 0.1 second VOX time, no call length or silence time out, dial next number on ring-no-answer 100321 (3 rings) and busy signal, 10pps pulse dialing speed.
- Page 8 Product Support: (715) 386-8666 Due to the dynamic nature of the product design, the information contained in this document is subject to change without notice. Viking Electronics, and its affiliates and/or subsidiaries assume no responsibility for errors and omissions contained in this information. Revisions of this document or new editions of it may be issued to incorporate such changes.
Need help?
Do you have a question about the PB-1 and is the answer not in the manual?
Questions and answers