Toyota Tundra 2005 Service - Repair - Maintenance page 182

SS−10
ENGINE MECHANICAL (2UZ−FE)
SERVICE DATA
Compression
pressure
Difference of pressure between each cylinder
Valve
clearance
Valve clearance adjusting shim
Ignition timing
Idle speed −
Timing belt Protrusion from housing end
tensioner
SERVICE SPECIFICATIONS
at 250 rpm STD
w/ Terminals TC and E1 connected of DLC1 5 to15° BTDC @ idle
− ENGINE MECHANICAL (2UZ−FE)
1,373 kPa (14.0 kgf/cm
Minimum 1,030 kPa (10.5 kgf/cm
98 kPa (1.0 kgf/cm
at cold Intake 0.15 to 0.25 mm (0.006 to 0.010 in.)
Exhaust 0.25 to 0.35 mm (0.010 to 0.014 in.)
No.00 2.000 mm (0.0787 in.)
No.02 2.020 mm (0.0795 in.)
No.04 2.040 mm (0.0803 in.)
No.06 2.060 mm (0.0811 in.)
No.08 2.080 mm (0.0819 in.)
No.10 2.100 mm (0.0827 in.)
No.12 2.120 mm (0.0835 in.)
No.14 2.140 mm (0.0843 in.)
No.16 2.160 mm (0.0850 in.)
No.18 2.180 mm (0.0858 in.)
No.20 2.200 mm (0.0866 in.)
No.22 2.220 mm (0.0874 in.)
No.24 2.240 mm (0.0882 in.)
No.26 2.260 mm (0.0890 in.)
No.28 2.280 mm (0.0898 in.)
No.30 2.300 mm (0.0906 in.)
No.32 2.320 mm (0.0913 in.)
No.34 2.340 mm (0.0921 in.)
No.36 2.360 mm (0.0929 in.)
No.38 2.380 mm (0.0937 in.)
No.40 2.400 mm (0.0945 in.)
No.42 2.420 mm (0.0953 in.)
No.44 2.440 mm (0.0961 in.)
No.46 2.460 mm (0.0969 in.)
No.48 2.480 mm (0.0976 in.)
No.50 2.500 mm (0.0984 in.)
No.52 2.520 mm (0.0992 in.)
No.54 2.540 mm (0.1000 in.)
No.56 2.560 mm (0.1008 in.)
No.58 2.580 mm (0.1016 in.)
No.60 2.600 mm (0.1024 in.)
No.62 2.620 mm (0.1031 in.)
No.64 2.640 mm (0.1039 in.)
No.66 2.660 mm (0.1047 in.)
No.68 2.680 mm (0.1055 in.)
No.70 2.700 mm (0.1063 in.)
No.72 2.720 mm (0.1071 in.)
No.74 2.740 mm (0.1079 in.)
No.76 2.760 mm (0.1087 in.)
No.78 2.780 mm (0.1094 in.)
No.80 2.800 mm (0.1102 in.)
700 ± 50 rpm
10.5 to 11.5 mm (0.413 to 0.453 in.)
2
, 199 psi) or more
2
, 149 psi)
2
, 14 psi) or less
SS0OQ−13