Kenwood TK-3360 Service Manual page 12

Hide thumbs Also See for TK-3360:
Table of Contents

Advertisement

TK-3360
2-5. Audio Amplifi er Circuit
The demodulated signal from IC401 is amplifi ed by IC812,
and goes to AF amplifi er through IC815.
The signal then goes through an volume control (IC817),
and is routed to an audio power amplifi er (IC815) where it is
amplifi ed and output to the speaker.
2-6. Squelch Circuit
Part of the AF signal from the IC401 enters the FM IC
(IC401) again, and the noise component is amplified and
rectifi ed by a fi lter and an amplifi er to produce a DC voltage
corresponding to the noise level.
The DC signal from the FM IC goes to the analog port of
the MCU (IC809). IC809 determines whether or not to out-
put sounds from the speaker by checking if the input volt-
age is higher or lower than the preset value.
To output sounds from the speaker, IC809 sends a high
signal to the AFSW line and turns IC815 on through Q813,
Q814, Q818 and Q819.
3. Transmitter System
3-1. Microphone Amplifi er Circuit
The signal from microphone amplifi ed by IC812 and lim-
ited by AGC circuit composed of D807, D808, Q810 and
Q811, and goes through mute switch (Q809). IC812 is com-
posed of high-pass fi lter, low-pass fi lter and pre-emphasis/
IDC circuit.
The output signal from the baseband IC (IC812) goes to
the VCO modulation input. The other output signal from the
baseband IC goes to the TCXO modulation input.
12
CIRCUIT DESCRIPTION /
MIC
D807,808
AGC
Q810,811
SW
MICM
Q809
Fig. 4 Microphone amplifi er circuit / 图 4 麦克风放大器电路
电路说明
2-5. 音频放大器电路
来自于 I C401 的解调信号被 I C812 放大,并通过 I C815 送
到 AF 放大器。
信号通过 AF 音量控制 (IC817), 在音频功率放大器 (IC815)
进行放大后输出到扬声器。
2-6. 静噪电路
FM IC(IC401) 输出的 AF 信号的一部分再进入 IC,噪声成
份通过滤波器和放大器进行放大和修正,生成与噪声电平相
应的 DC 电压。
D C 信号通过 F M I C 被送到微处理器的模拟端口 ( I C809)。
IC809 通过检测输入的电压是高于还是低于预设值来决定是否
从扬声器输出声音。
由扬声器输出声音时,I C809 发送高电平信号给 A F S W,通
过 Q813、Q814、Q818 和 Q819 打开 IC815。
3. 发射机系统
3-1. 麦克风放大器电路
麦 克 风 的 信 号 被 I C812 放 大, 并 受 由 D807、D808、Q810
和 Q811 组成的 A G C 电路的限幅,然后通过静音开关 ( Q809)。
IC812 由高通滤波器、低通滤波器和预加重 /IDC 电路组成。
基带 IC(IC812) 的输出信号送入 VCO 调制输入。基带 IC 的
其他输出信号送入 TCXO 调制输入。
IC812
VCO
Baseband
X1
IC
TCXO
LSD
OUT

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents