Related Manuals for IBASE Technology ET870 Series
Summary of Contents for IBASE Technology ET870 Series
- Page 1 ET870 Series COM Express Type 6 Module Atom™ x7/x5 ® With Intel User’s Manual Version 1.0 (Jan. 2019)
- Page 2 No part of this publication may be reproduced, copied, stored in a retrieval system, translated into any language or transmitted in any form or by any means, electronic, mechanical, photocopying, or otherwise, without the prior written consent of IBASE Technology, Inc. (hereinafter referred to as “IBASE”). Disclaimer IBASE reserves the right to make changes and improvements to the products described in this document without prior notice.
-
Page 3: Compliance
0.1% by weight (1000 ppm) except for cadmium, limited to 0.01% by weight (100 ppm). • Lead (Pb) • Mercury (Hg) • Cadmium (Cd) • Hexavalent chromium (Cr6+) • Polybrominated biphenyls (PBB) • Polybrominated diphenyl ether (PBDE) ET870 Series User’s Manual... -
Page 4: Important Safety Information
Danger of explosion if the internal lithium-ion battery is replaced by an incorrect type. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions or recycle them at a local recycling facility or battery collection point. ET870 Series User’s Manual... -
Page 5: Warranty Policy
Software in use (such as OS and application software, including the version numbers) If repair service is required, you can download the RMA form at http://www.ibase.com.tw/english/Supports/RMAService/. Fill out the form and contact your distributor or sales representative. ET870 Series User’s Manual... -
Page 6: Table Of Contents
® Intel Trusted Execution Engine Drivers ..........24 ® Intel Serial IO Drivers ..............26 LAN Driver Installation ............... 28 Chapter 4 BIOS Setup............31 Introduction ..................32 BIOS Setup ..................32 Main Settings ..................33 ET870 Series User’s Manual... - Page 7 4.5.3 SATA Drives .................47 4.5.4 USB Configuration ..............48 Security Settings ................48 Boot Settings ..................49 Save & Exit Settings ................50 Appendix ..................51 I/O Port Address Map ................52 Interrupt Request Lines (IRQ) ............55 Watchdog Timer Configuration ............57 ET870 Series User’s Manual...
- Page 8 This page is intentionally left blank. ET870 Series User’s Manual viii...
-
Page 9: Chapter 1 General Information
Chapter 1 General Information The information provided in this chapter includes: • Features • Packing List • Optional Accessories • Specifications • Block Diagram • Board Overview • Board Dimensions... -
Page 10: Introduction
2 x independent displays of DisplayPort / DVI-D / LVDS or eDP, and HD audio jacks for line-in, line-out, mic-in via the carrier board (IP419) • Wide-range operating temperature • Configurable watchdog timer and TPM 2.0 ET870 Series User’s Manual... -
Page 11: Packing List
2 x DDI For ET870-I50: For ET870-I30: 1 x eDP 1 x eDP Display For ET870-I50LV: For ET870-I30LV: 1 x 24-bit dual channel LVDS 1 x 24-bit dual channel LVDS ® Audio Intel Atom™ SoC built-in HD Audio ET870 Series User’s Manual... - Page 12 • Operation: -40 ~ 85 °C (-40 ~ 185 °F) Temperature • Storage: -40 ~ 90 °C (-40 ~ 194 °F) Relative 10 ~ 90 %, non-condensing Humidity All specifications are subject to change without prior notice. ET870 Series User’s Manual...
-
Page 13: Block Diagram
General Information Block Diagram ET870 Series User’s Manual... -
Page 14: Overview
Overview Top View Bottom View Photos of ET870 ＊The photos above are for reference only. Some minor components may differ. ET870 Series User’s Manual... -
Page 15: Dimensions
General Information Dimensions Unit: mm ET870 Series User’s Manual... - Page 16 This page is intentionally left blank. ET870 Series User’s Manual...
-
Page 17: Chapter 2 Hardware Configuration
Chapter 2 Hardware Configuration This section provides information on jumper settings and connectors on the ET870 in order to set up a workable system. On top of that, you will also need to install crucial pieces such as the CPU and the memory before using the product. The topics covered are: •... -
Page 18: Installations
Gently push the module in an upright position until the clips of the slot close to hold the module in place when the module touches the bottom of the slot. To remove the module, press the clips outwards with both hands, and the module will pop-up. ET870 Series User’s Manual... -
Page 19: Connector Location
Hardware Configuration Connector Location SOM1 SOM2 Board diagram of ET870 ET870 Series User’s Manual... -
Page 20: Connector Quick Reference
AT / ATX Mode Switch SW10 Connector to Carrier Board SOM1, SOM2 DDR3L SO-DIMM Slot J1, J2 2.3.1 AT / ATX Mode Switch (SW10) Function Pin closed Illustration ATX Mode (default) OFF (Pin 1) AT Mode ON (Pin 2) ET870 Series User’s Manual... - Page 21 GND (FIXED) SATA2_TX+ SATA3_TX+ PCIE_RX7+ PCIE_TX7+ SATA2_TX- SATA3_TX- PCIE_RX7- PCIE_TX7- SUS_S5# PWR_OK DDI1_HPD RSVD SATA2_RX+ SATA3_RX+ DDI1_PAIR4+ RSVD SATA2_RX- SATA3_RX- DDI1_PAIR4- DDI1_PAIR0+ BATLOW# RSVD DDI1_PAIR0- SATA_ACT# HDA_SDIN2 RSVD RSVD HDA_SYNC HDA_SDIN1 DDI1_PAIR5+ DDI1_PAIR1+ HDA_RST# HDA_SDIN0 DDI1_PAIR5- DDI1_PAIR1- ET870 Series User’s Manual...
- Page 22 WAKE1# RAPID_SHUTDOW PCIE_TX0+ PCIE_RX0+ PEG_RX5+ PEG_TX5+ PCIE_TX0- PCIE_RX0- PEG_RX5- PEG_TX5- GND (FIXED) GND (FIXED) GND (FIXED) GND (FIXED) LVDS_A0+ LVDS_B0+ PEG_RX6+ PEG_TX6+ LVDS_A0- LVDS_B0- PEG_RX6- PEG_TX6- LVDS_A1+ LVDS_B1+ LVDS_A1- LVDS_B1- PEG_RX7+ PEG_TX7+ LVDS_A2+ LVDS_B2+ PEG_RX7- PEG_TX7- ET870 Series User’s Manual...
- Page 23 A107 VCC_12V B107 VCC_12V C107 VCC_12V D107 VCC_12V A108 VCC_12V B108 VCC_12V C108 VCC_12V D108 VCC_12V A109 VCC_12V B109 VCC_12V C109 VCC_12V D109 VCC_12V A110 GND (FIXED) B110 GND (FIXED) C110 GND (FIXED) D110 GND (FIXED) ET870 Series User’s Manual...
- Page 24 This page is intentionally left blank. ET870 Series User’s Manual...
-
Page 25: Chapter 3 Drivers Installation
Chapter 3 Drivers Installation This chapter introduces installation of the following drivers: • ® Intel Chipset Software Installation Utility • Graphics Driver • HD Audio Driver • ® Intel Trusted Execution Engine Drivers • ® Intel Serial I/O Drivers • LAN Driver... -
Page 26: Introduction
INF files for Plug & Play function for Intel chipset components. Follow the instructions below to complete the installation. Insert the disk enclosed in the package with the board. Click Intel on the left pane and then Intel(R) Apollolake Chipset Drivers on the right pane. ET870 Series User’s Manual... - Page 27 Click Yes to accept the software license agreement and proceed with the installation process. On the Readme File Information screen, click Install for installation. The driver has been completely installed. Restart the computer for changes to take effect. ET870 Series User’s Manual...
-
Page 28: Graphics Driver Installation
Graphics Driver Installation Click Intel on the left pane and then Intel(R) Apollolake Chipset Drivers on the right pane. Click Intel(R) Apollolake Graphics Driver. ET870 Series User’s Manual... - Page 29 When the Welcome screen appears, click Next to continue. Click Yes to accept the license agreement and click Next until the installation starts. The driver has been completely installed. Restart the computer for changes to take effect. ET870 Series User’s Manual...
-
Page 30: Hd Audio Driver Installation
HD Audio Driver Installation Click Intel on the left pane and then Intel(R) Apollolake Chipset Drivers on the right pane. Click Realtek High Definition Audio Driver. ET870 Series User’s Manual... - Page 31 Driver Installation On the Welcome screen of the InstallShield Wizard, click Next. Click Next until the installation starts. The driver has been completely installed. Restart the computer for changes to take effect. ET870 Series User’s Manual...
-
Page 32: Intel Trusted Execution Engine Drivers
® Intel Trusted Execution Engine Drivers Click Intel on the left pane and then Intel(R) Apollolake Chipset Drivers on the right pane. Click Intel(R) TXE Drivers. ET870 Series User’s Manual... - Page 33 Driver Installation When the Welcome screen appears, click Next. Accept the license agreement and click Next. Click Next for installation. As the driver has been sccessfully installed, restart the computer for changes to take effect. ET870 Series User’s Manual...
-
Page 34: Intel Serial Io Drivers
® Intel Serial IO Drivers Click Intel on the left pane and then Intel(R) Apollolake Chipset Drivers on the right pane. Click Intel(R) Serial IO Drivers. ET870 Series User’s Manual... - Page 35 When the Welcome screen to the InstallShield Wizard appears, click Next. Accept the license agreement and click Next. After reading the Readme File Information, click Next for installation. As the driver has been sccessfully installed, restart the computer for changes to take effect. ET870 Series User’s Manual...
-
Page 36: Lan Driver Installation
LAN Driver Installation Click LAN Card on the left pane and then Intel LAN Controller Drivers on the right pane. Click Intel(R) I21x Gigabit Network Drivers.. ET870 Series User’s Manual... - Page 37 On the Setup Options screen, click the checkbox to select the desired driver(s) for installation. Then click Next to continue. The wizard is ready for installation. Click Install. As the installation is complete, restart the computer for changes to take effect. ET870 Series User’s Manual...
- Page 38 This page is intentionally left blank. ET870 Series User’s Manual...
-
Page 39: Chapter 4 Bios Setup
Chapter 4 BIOS Setup This chapter describes the different settings available in the AMI BIOS that comes with the board. The topics covered in this chapter are as follows: • Main Settings • Advanced Settings • Chipset Settings • Security Settings •... -
Page 40: Introduction
These defaults have been carefully chosen by both AMI and your system manufacturer to provide the absolute maximum performance and reliability. Changing the defaults could make the system unstable and crash in some cases. ET870 Series User’s Manual... -
Page 41: Main Settings
Advanced Settings This section allows you to configure, improve your system and allows you to set up some system features according to your preference. Note: The item LVDS (eDP/DP) Configuration is only available for ET870-I50LV & ET870-I30LV. ET870 Series User’s Manual... -
Page 42: Trusted Computing
TCG_2: supports new TCG2 protocol and event format for Windows 10 or later. Physical Presence Selects to show the PPI Spec Version (1.2 or 1.3) Spec Version that the OS supports. Note: Some HCK tests might not support 1.3. ET870 Series User’s Manual... -
Page 43: Acpi Settings
Enables / Disables the system ability to hibernate (OS/S4 Sleep State). This option may be not effective with some OS. ACPI Sleep State Selects an ACPI sleep state (Suspend Disabled or S3) where the system will enter when the Suspend button is pressed. ET870 Series User’s Manual... -
Page 44: Lvds (Edp/Dp) Configuration
Options: 800 x 600 / 1024 x 768 / 1280 x 1024 / 1366 x 768 / 1440 x 900 / 1600 x 900 / 1920 x 1080 Brightness Percent Selects a level of brightness. Options: Level-1 ~ Level-8 ET870 Series User’s Manual... -
Page 45: Fintek Super Io Configuration
Change Settings Selects an optimal settings for Super I/O device. 4.4.4.2. Serial Port 2 Configuration BIOS Setting Description Serial Port Enables / Disables the serial port. Change Settings Selects an optimal settings for Super I/O device. ET870 Series User’s Manual... - Page 46 Changes the printer port mode. Options: STD Printer Mode / SPP Mode / EPP-1.9 and SPP Mode / EPP-1.7 and SPP Mode / ECP Mode / ECP and EPP 1.9 Mode / ECP and EPP 1.7 Mode ET870 Series User’s Manual...
-
Page 47: F81804Sec Super Io Configuration
Change Settings Selects an optimal settings for Super I/O device. 4.4.5.2. Serial Port 2 Configuration BIOS Setting Description Serial Port Enables / Disables the serial port. Change Settings Selects an optimal settings for Super I/O device. ET870 Series User’s Manual... -
Page 48: F81804 Hardware Monitor
Enables / Disables the CPU fan control. Control Temperatures / These fields are the parameters of the hardware Voltages monitoring function feature of the motherboard. The values are read-only values as monitored by the system and show the PC health status. ET870 Series User’s Manual... -
Page 49: Setup
BIOS Setting Description M.2 Select Selects SATA or PCIe interface for M.2. 4.4.8 CPU Configuration BIOS Setting Description Socket 0 CPU Displays the socket specific CPU information. Information CPU Power Show the CPU power management options. Management ET870 Series User’s Manual... -
Page 50: Network Stack Configuration
4.4.8.1. Socket 0 CPU Information 4.4.8.2. CPU Power Management BIOS Setting Description Turbo Mode Enables / Disables the turbo mode. 4.4.9 Network Stack Configuration BIOS Setting Description Network Stack Enables / Disables UEFI network stack. ET870 Series User’s Manual... -
Page 51: Csm Configuration
OpROM. Storage Controls the execution of UEFI and Legacy Storage OpROM. Video Controls the execution of UEFI and Legacy Video OpROM. Other PCI Determines OpROM execution policy for devices other devices than network, storage or video. ET870 Series User’s Manual... -
Page 52: Usb Configuration
“Auto” enumerates devices according to their media format. Optical drives are emulated as “CDROM”, drivers with no media will be emulated according to a drive type. Options: Auto / Floppy / Forced FDD / Hard Disk / CD-ROM ET870 Series User’s Manual... -
Page 53: Chipset Settings
BIOS Setup Chipset Settings ET870 Series User’s Manual... -
Page 54: Hd-Audio Configuration
BIOS Setting Description PCI Express Root Control the PCI Express Root Port. Ports 1 ~ 6 Enables / Disables PCIe root port. Auto is to disable unused root port automatically for the most optimum power savings. ET870 Series User’s Manual... -
Page 55: Sata Drives
Description Chipset SATA Enables / Disables the chipset SATA controller. The chipsest SATA Controller supports the 2 black internal SATA ports (up to 3Gb/s supported per port). SATA Mode Selection Selects AHCI for SATA Controller(s) operation. ET870 Series User’s Manual... -
Page 56: Usb Configuration
OS. Do not disable it unless for debug purpose. Security Settings BIOS Setting Description Administrator Sets an administrator password for the setup Password utility. User Password Sets a user password. ET870 Series User’s Manual... -
Page 57: Boot Settings
Selects a Boot mode, Legacy / UEFI. Boot Option Priorities Sets the system boot order priorities for hard disk, CD/DVD, USB, Network. UEFI USB Key Drive Specificies the Boot device priority sequence BBS Priorities from available UEFI USB Key drivers. ET870 Series User’s Manual... -
Page 58: Save & Exit Settings
Restore Defaults Restores / Loads defaults values for all the setup options. Save as User Defaults Saves the changes done so far as User Defaults. Restore User Defaults Restores the user defaults to all the setup options. ET870 Series User’s Manual... -
Page 59: Appendix
Appendix This section provides the mapping addresses of peripheral devices and the sample code of watchdog timer configuration. -
Page 60: I/O Port Address Map
0x00000680-0x0000069F Motherboard resources 0x00000400-0x0000047F Motherboard resources 0x00000500-0x000005FE Motherboard resources 0x00000600-0x0000061F Motherboard resources 0x0000164E-0x0000164F Motherboard resources 0x00000378-0x0000037F Printer Port (LPT1) 0x0000F040-0x0000F05F Intel(R) Celeron(R)/Pentium(R) Processor SMBUS - 5AD4 0x0000E000-0x0000EFFF Intel(R) Celeron(R)/Pentium(R) Processor PCI Express Root Port - 5ADA ET870 Series User’s Manual... - Page 61 Programmable interrupt controller 0x000000A8-0x000000A9 Programmable interrupt controller 0x000000AC-0x000000AD Programmable interrupt controller 0x000000B0-0x000000B1 Programmable interrupt controller 0x000000B4-0x000000B5 Programmable interrupt controller 0x000000B8-0x000000B9 Programmable interrupt controller 0x000000BC-0x000000BD Programmable interrupt controller 0x000004D0-0x000004D1 Programmable interrupt controller 0x0000F090-0x0000F097 Standard SATA AHCI Controller ET870 Series User’s Manual...
- Page 62 Address Device Description 0x0000F080-0x0000F083 Standard SATA AHCI Controller 0x0000F060-0x0000F07F Standard SATA AHCI Controller 0x00000040-0x00000043 System timer 0x00000050-0x00000053 System timer ET870 Series User’s Manual...
-
Page 63: Interrupt Request Lines (Irq)
Intel(R) I210 Gigabit Network Connection #2 IRQ 4294967280 Intel(R) I210 Gigabit Network Connection #2 IRQ 4294967292 Intel(R) Trusted Execution Engine Interface IRQ 14 Intel(R) Serial IO GPIO Host Controller - INT3452 IRQ 14 Intel(R) Serial IO GPIO Host Controller - INT3452 ET870 Series User’s Manual... - Page 64 Level Function IRQ 14 Intel(R) Serial IO GPIO Host Controller - INT3452 IRQ 14 Intel(R) Serial IO GPIO Host Controller - INT3452 IRQ 4294967294 Standard SATA AHCI Controller IRQ 0 System timer ET870 Series User’s Manual...
-
Page 65: Watchdog Timer Configuration
**endptr; char SIO; printf("Fintek 81804 watch dog program\n"); SIO = Init_F81804(); if (SIO == 0) printf("Can not detect Fintek 81804, program abort.\n"); return(1); }//if (SIO == 0) if (argc != 2) printf(" Parameter incorrect!!\n"); return (1); ET870 Series User’s Manual... - Page 66 DisableWDT(void) unsigned char bBuf; Set_F81804_LD(0x07); //switch to logic device 7 bBuf = Get_F81804_Reg(0xFA); bBuf &= ~0x01; Set_F81804_Reg(0xFA, bBuf); //disable WDTO output bBuf = Get_F81804_Reg(0xF5); bBuf &= ~0x20; bBuf |= 0x40; Set_F81804_Reg(0xF5, bBuf); //disable WDT //--------------------------------------------------------------------------- //--------------------------------------------------------------------------- ET870 Series User’s Manual...
- Page 67 Init_Finish; F81804_BASE = 0x00; result = F81804_BASE; Init_Finish: return (result); //--------------------------------------------------------------------------- void Unlock_F81804 (void) outportb(F81804_INDEX_PORT, F81804_UNLOCK); outportb(F81804_INDEX_PORT, F81804_UNLOCK); //--------------------------------------------------------------------------- void Lock_F81804 (void) outportb(F81804_INDEX_PORT, F81804_LOCK); //--------------------------------------------------------------------------- void Set_F81804_LD( unsigned char LD) Unlock_F81804(); outportb(F81804_INDEX_PORT, F81804_REG_LD); outportb(F81804_DATA_PORT, LD); Lock_F81804(); ET870 Series User’s Manual...
- Page 68 F81804_DATA_PORT (F81804_BASE+1) //--------------------------------------------------------------------------- #define F81804_REG_LD 0x07 //--------------------------------------------------------------------------- #define F81804_UNLOCK 0x87 #define F81804_LOCK 0xAA //--------------------------------------------------------------------------- unsigned int Init_F81804(void); void Set_F81804_LD( unsigned char); void Set_F81804_Reg( unsigned char, unsigned char); unsigned char Get_F81804_Reg( unsigned char); //--------------------------------------------------------------------------- #endif // F81804_H ET870 Series User’s Manual...