Related Manuals for IBASE Technology IBQ800 Series
Summary of Contents for IBASE Technology IBQ800 Series
- Page 1 IBQ800 Series Qseven CPU Module Atom™ x7/x5 ® With Intel User’s Manual Version 1.0 (Oct. 2018)
- Page 2 No part of this publication may be reproduced, copied, stored in a retrieval system, translated into any language or transmitted in any form or by any means, electronic, mechanical, photocopying, or otherwise, without the prior written consent of IBASE Technology, Inc. (hereinafter referred to as “IBASE”). Disclaimer IBASE reserves the right to make changes and improvements to the products described in this document without prior notice.
-
Page 3: Compliance
0.1% by weight (1000 ppm) except for cadmium, limited to 0.01% by weight (100 ppm). • Lead (Pb) • Mercury (Hg) • Cadmium (Cd) • Hexavalent chromium (Cr6+) • Polybrominated biphenyls (PBB) • Polybrominated diphenyl ether (PBDE) IBQ800 Series User’s Manual... -
Page 4: Important Safety Information
Danger of explosion if the internal lithium-ion battery is replaced by an incorrect type. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions or recycle them at a local recycling facility or battery collection point. IBQ800 Series User’s Manual... -
Page 5: Warranty Policy
Software in use (such as OS and application software, including the version numbers) If repair service is required, you can download the RMA form at http://www.ibase.com.tw/english/Supports/RMAService/. Fill out the form and contact your distributor or sales representative. IBQ800 Series User’s Manual... -
Page 6: Table Of Contents
Serial IO Drivers ..............24 LAN Driver Installation ............... 26 Chapter 4 BIOS Setup............29 Introduction ..................30 BIOS Setup ..................30 Main Settings ..................31 Advanced Settings ................31 4.4.1 Trusted Computing ............... 32 4.4.2 ACPI Settings ............... 33 IBQ800 Series User’s Manual... - Page 7 4.5.5 USB Configuration ..............50 Security Settings ................51 4.6.1 Secure Boot ................52 Boot Settings ..................53 Save & Exit Settings ................54 Appendix ..................55 I/O Port Address Map ................56 Interrupt Request Lines (IRQ) ............58 Watchdog Timer Configuration ............59 IBQ800 Series User’s Manual...
- Page 8 This page is intentionally left blank. IBQ800 Series User’s Manual viii...
-
Page 9: Chapter 1 General Information
Chapter 1 General Information The information provided in this chapter includes: • Features • Packing List • Optional Accessories • Specifications • Block Diagram • Board Overview • Board Dimensions... -
Page 10: Introduction
Features • Atom™ x7-E3950 / x5-E3930 processor ® Onboard Intel • Onboard LPDDR4 memory • ® Intel I210IT PCIe GbE LAN • Wide-range operating temperature • Configurable watchdog timer and TPM 2.0 • eMMC 5.0 (Optional) IBQ800 Series User’s Manual... -
Page 11: Packing List
Derived from Qseven CPU module: • 3 x USB 3.0 • 4 x USB 2.0 Expansion 4 x PCIe (x1) SATA 2 x SATA 3.0 (6Gb/sec.) thru interface on carrier board ® Intel Atom SoC built-in HD Audio controller Audio IBQ800 Series User’s Manual... - Page 12 • Storage: -40 ~ 90 °C (-40 ~ 194 °F) Relative 90%, non-condensing at 60°C Humidity Heat spreader Others IP416 will be the carrier board for testing All specifications are subject to change without prior notice. IBQ800 Series User’s Manual...
-
Page 13: Block Diagram
General Information Block Diagram IBQ800 Series User’s Manual... -
Page 14: Overview
Overview Top View Bottom View Photos of IBQ800 ＊The photos above are for reference only. Some minor components may differ. IBQ800 Series User’s Manual... -
Page 15: Dimensions
General Information Dimensions Unit: mm IBQ800 Series User’s Manual... - Page 16 This page is intentionally left blank. IBQ800 Series User’s Manual...
-
Page 17: Chapter 2 Pin Definition
Chapter 2 Pin Definition This section provides the pin definition of the 230-pin MXM2 SMT edge connector. -
Page 18: Connector Location
Connector Location Board diagram of IBQ800 IBQ800 Series User’s Manual... -
Page 19: Edge Connector
Ground Ground BIOS_DISABLE# SDIO_CLK# SDIO_CD# Reserved SDIO_CMD SDIO_WP SDIO_PWR# SDIO_DATA1 SDIO_DATA0 SDIO_DATA3 SDIO_DATA2 Reserved Reserved Reserved Reserved Reserved Ground Ground HAD_SYNC SMB_CLK HAD_RST# SMB_DAT HAD_BITCLK SMB_ALERT# HAD_SDI GP0_I2C_CLK HAD_SDO GP0_I2C_DAT THRM# WDTRIG# THRMTRIP# WDOUT Ground Ground IBQ800 Series User’s Manual... - Page 20 LVDS_B_CLK+ eDP0_AUX-/LVDS_A_CLK- LVDS_B_CLK- LVDS_BKLT_CTRL Reserved LVDS_DDC_DAT eDP0_HPD# LVDS_DDC_CLK Reserved Reserved Reserved DP_LANE3+/TMDS_CLK+ U3_USB1_TX_N DP_LANE3-/TMDS_CLK- U3_USB1_TX_P Ground Ground DP_LANE1+/TMDS_LANE1+ DP_AUX+ DP_LANE1-/TMDS_LANE1- DP_AUX- Ground Ground DP_LANE2+/TMDS_LANE0+ U3_USB1_RX_N DP_LANE2-/TMDS_LANE0- U3_USB1_RX_P Ground Ground DP_LANE0+/TMDS_LANE2+ HDMI_CTRL_DAT DP_LANE0-/TMDS_LANE2- HDMI_CTRL_CLK DP_HDMI_HPD# DP_HPD# IBQ800 Series User’s Manual...
- Page 21 PCIE2_RX- UART0_TX UART0_RTS# PCIE1_TX+ PCIE1_RX+ PCIE1_TX- PCIE1_RX- UART0_RX UART0_CTS# PCIE0_TX+ PCIE0_RX+ PCIE0_TX- PCIE0_RX- Ground Ground LPC_AD0 LPC_AD1 LPC_AD2 LPC_AD3 LPC_CLK LPC_FRAME# LPC_SERIRQ LPC_LDRQ# VCC_RTC SPKR FAN_TACHOIN FAN_PWMOUT Ground Ground SPI_MOSI SPI_CS0# SPI_MISO SPI_CS1# SPI_SCK VCC_5V_SB VCC_5V_SB IBQ800 Series User’s Manual...
- Page 22 This page is intentionally left blank. IBQ800 Series User’s Manual...
-
Page 23: Chapter 3 Drivers Installation
Chapter 3 Drivers Installation This chapter introduces installation of the following drivers: • ® Intel Chipset Software Installation Utility • Graphics Driver • HD Audio Driver • ® Intel Trusted Execution Engine Drivers • ® Intel Serial I/O Drivers • LAN Driver... -
Page 24: Introduction
INF files for Plug & Play function for Intel chipset components. Follow the instructions below to complete the installation. Insert the disk enclosed in the package with the board. Click Intel on the left pane and then Intel(R) Apollolake Chipset Drivers on the right pane. IBQ800 Series User’s Manual... - Page 25 Click Yes to accept the software license agreement and proceed with the installation process. On the Readme File Information screen, click Install for installation. As the driver is completely installed, restart the computer for changes to take effect. IBQ800 Series User’s Manual...
-
Page 26: Graphics Driver Installation
Graphics Driver Installation Click Intel on the left pane and then Intel(R) Apollolake Chipset Drivers on the right pane. Click Intel(R) Apollolake Graphics Driver. IBQ800 Series User’s Manual... - Page 27 When the Welcome screen appears, click Next to continue. Click Yes to accept the license agreement and click Next until the installation starts. As the driver is completely installed, restart the computer for changes to take effect. IBQ800 Series User’s Manual...
-
Page 28: Hd Audio Driver Installation
HD Audio Driver Installation Click Intel on the left pane and then Intel(R) Apollolake Chipset Drivers on the right pane. Click Realtek High Definition Audio Driver. IBQ800 Series User’s Manual... - Page 29 Driver Installation On the Welcome screen of the InstallShield Wizard, click Next. Click Next until the installation starts. As the driver is completely installed, restart the computer for changes to take effect. IBQ800 Series User’s Manual...
-
Page 30: Intel Trusted Execution Engine Drivers
® Intel Trusted Execution Engine Drivers Click Intel on the left pane and then Intel(R) Apollolake Chipset Drivers on the right pane. Click Intel(R) TXE Drivers. IBQ800 Series User’s Manual... - Page 31 Driver Installation When the Welcome screen appears, click Next. Accept the license agreement and click Next. Click Next for installation. As the driver is sccessfully installed, restart the computer for changes to take effect. IBQ800 Series User’s Manual...
-
Page 32: Intel Serial Io Drivers
® Intel Serial IO Drivers Click Intel on the left pane and then Intel(R) Apollolake Chipset Drivers on the right pane. Click Intel(R) Serial IO Drivers. IBQ800 Series User’s Manual... - Page 33 When the Welcome screen to the InstallShield Wizard appears, click Next. Accept the license agreement and click Next. After reading the Readme File Information, click Next for installation. As the driver is sccessfully installed, restart the computer for changes to take effect. IBQ800 Series User’s Manual...
-
Page 34: Lan Driver Installation
LAN Driver Installation Click LAN Card on the left pane and then Intel LAN Controller Drivers on the right pane. Click Intel(R) I21x Gigabit Network Drivers.. IBQ800 Series User’s Manual... - Page 35 On the Setup Options screen, click the checkbox to select the desired driver(s) for installation. Then click Next to continue. The wizard is ready for installation. Click Install. As the installation is complete, restart the computer for changes to take effect. IBQ800 Series User’s Manual...
- Page 36 This page is intentionally left blank. IBQ800 Series User’s Manual...
-
Page 37: Chapter 4 Bios Setup
Chapter 4 BIOS Setup This chapter describes the different settings available in the AMI BIOS that comes with the board. The topics covered in this chapter are as follows: • Main Settings • Advanced Settings • Chipset Settings • Security Settings •... -
Page 38: Introduction
These defaults have been carefully chosen by both AMI and your system manufacturer to provide the absolute maximum performance and reliability. Changing the defaults could make the system unstable and crash in some cases. IBQ800 Series User’s Manual... -
Page 39: Main Settings
Set the time. Use the <Tab> key to switch between the data elements. Advanced Settings This section allows you to configure, improve your system and allows you to set up some system features according to your preference. IBQ800 Series User’s Manual... -
Page 40: Trusted Computing
TCG_2: supports new TCG2 protocol and event format for Windows 10 or later. Physical Presence Selects to show the PPI Spec Version (1.2 or 1.3) Spec Version that the OS supports. Note: Some HCK tests might not support 1.3. IBQ800 Series User’s Manual... -
Page 41: Acpi Settings
Enables / Disables the system ability to hibernate (OS/S4 Sleep State). This option may be not effective with some OS. ACPI Sleep State Selects an ACPI sleep state (Suspend Disabled or S3) where the system will enter when the Suspend button is pressed. IBQ800 Series User’s Manual... -
Page 42: Lvds (Edp/Dp) Configuration
1024 / 1366 x 768 / 1440 x 900 / 1600 x 900 / 1600 x 1200 / 1680 x 1050 / 1920 x 1080 / 1920 x 1200 LVDS Backlight Level Selects a level of backlight. Control Options: Level-1 ~ Level-8 IBQ800 Series User’s Manual... -
Page 43: Fintek 81964 Sio Configuration
IO = 2F8h; IRQ = 3, 4, 5, 6, 7, 9, 10, 11, 12 • IO = 3E8h; IRQ = 3, 4, 5, 6, 7, 9, 10, 11, 12 • IO = 2E8h; IRQ = 3, 4, 5, 6, 7, 9, 10, 11, 12 IBQ800 Series User’s Manual... - Page 44 IO = 2E8h; IRQ = 3, 4, 5, 6, 7, 9, 10, 11, 12 • IO = 2F0h; IRQ = 3, 4, 5, 6, 7, 9, 10, 11, 12 • IO = 2E0h; IRQ = 3, 4, 5, 6, 7, 9, 10, 11, 12 IBQ800 Series User’s Manual...
- Page 45 IO = 2E8h; IRQ = 3, 4, 5, 6, 7, 9, 10, 11, 12 • IO = 2F0h; IRQ = 3, 4, 5, 6, 7, 9, 10, 11, 12 • IO = 2E0h; IRQ = 3, 4, 5, 6, 7, 9, 10, 11, 12 IBQ800 Series User’s Manual...
-
Page 46: Fintek 81804 Sio Configuration
• IO = 240h; IRQ = 10 • IO = 240h; IRQ = 3, 4, 5, 6, 7, 10, 11, 12 • IO = 248h; IRQ = 3, 4, 5, 6, 7, 9, 10, 11, 12 IBQ800 Series User’s Manual... -
Page 47: Fintek 81804 Hardware Monitor
Options: Disabled, 50°C, 60°C, 70°C, 80°C Temperatures / These fields are the parameters of the hardware Voltages monitoring function feature of the motherboard. The values are read-only values as monitored by the system and show the PC health status. IBQ800 Series User’s Manual... -
Page 48: Cpu Configuration
4.4.7 CPU Configuration BIOS Setting Description Socket 0 CPU Displays the socket specific CPU information. Information CPU Power Show the CPU power management options. Management 4.4.7.1. Socket 0 CPU Information IBQ800 Series User’s Manual... -
Page 49: Ami Graphic Output Protocol Policy
BIOS Setup 4.4.8 AMI Graphic Output Protocol Policy BIOS Setting Description Output Select Outputs interface IBQ800 Series User’s Manual... -
Page 50: Network Stack Configuration
If disabled, Ipv4 HTTP boot option will not be created. PXE boot wait time Assigns a period of time to press ESC key to abort the PXE boot. Media detect count Assigns a number of times to check the presence of media. IBQ800 Series User’s Manual... -
Page 51: Csm Configuration
Option ROM. • Immediate executes the trap right away • Postponed executes the trap during legacy boot. Boot option filter Controls the priority of Legacy and UEFI. Network Controls the execution of UEFI and Legacy PXE OpROM. IBQ800 Series User’s Manual... -
Page 52: Sdio Configuration
Mass storage device emulation type. “Auto” (30.6 GB) enumerates devices less than 530 MB as floppies. Forced FDD option can be used to force HDD formatted drive to boot as FDD. Options: Auto, Floppy, Forced FDD, Hard Disk IBQ800 Series User’s Manual... -
Page 53: Usb Configuration
Maximum time the device will take before it delay properly reports itself to the Host Controller. “Auto” uses default value: for a root port it is 100 ms, for a hub port, the delay is taken from hub descriptor. IBQ800 Series User’s Manual... -
Page 54: Chipset Settings
Chipset Settings IBQ800 Series User’s Manual... -
Page 55: Hd-Audio Configuration
BIOS Setting Description PCI Express Root Control the PCI Express Root Port. Ports 1 ~ 6 Enables / Disables PCIe root port. Auto is to disable unused root port automatically for the most optimum power savings. IBQ800 Series User’s Manual... -
Page 56: Sata Drives
Description Chipset SATA Enables / Disables the chipset SATA controller. The chipsest SATA Controller supports the 2 black internal SATA ports (up to 3Gb/s supported per port). SATA Mode Selection Selects AHCI for SATA Controller(s) operation. IBQ800 Series User’s Manual... -
Page 57: Scc Configuration
Enables / Disables SCC SD card support. (D27:F0) SCC eMMC Support Enables / Disables SCC eMMC support. (D28:F0) eMMC Max Speed Selects the eMMC max. speed allowed. SCC SDIO Support Enables / Disables SCC SDIO support. (D30:F0) IBQ800 Series User’s Manual... -
Page 58: Usb Configuration
USB port from reporting a device connection to the controller. XDCI Support Enables / Disables XDCI. XHCI Disable FALSE makes the XHCI Link Compliance Mode Compliance Mode not disabled. TRUE disables the XHCI Link Compliance Mode. IBQ800 Series User’s Manual... -
Page 59: Security Settings
BIOS Setup Security Settings BIOS Setting Description Setup Administrator Sets an administrator password for the setup Password utility. User Password Sets a user password. Secure Boot Customizable secure boot settings. IBQ800 Series User’s Manual... -
Page 60: Secure Boot
CSM function is disabled. Secure Boot Mode Custom & standard modes for UEFI secure boot mode. This change will be effective after being saved. After reset, the mode will return to standard mode. IBQ800 Series User’s Manual... -
Page 61: Boot Settings
Selects a Boot mode, Legacy / UEFI. Boot Option Priorities Sets the system boot order priorities for hard disk, CD/DVD, USB, Network. UEFI Hard Disk Drive Specificies the Boot device priority sequence BBS Priorities from available UEFI USB Key drivers. IBQ800 Series User’s Manual... -
Page 62: Save & Exit Settings
Restore Defaults Restores / Loads defaults values for all the setup options. Save as User Defaults Saves the changes done so far as User Defaults. Restore User Defaults Restores the user defaults to all the setup options. IBQ800 Series User’s Manual... -
Page 63: Appendix
Appendix This section provides the mapping addresses of peripheral devices and the sample code of watchdog timer configuration. -
Page 64: I/O Port Address Map
Motherboard resources 0x0000E000-0x0000EFFF Intel(R) Celeron(R)/Pentium(R) Processor PCI Express Root Port - 5AD6 0x000003F8-0x000003FF Communications Port (COM1) 0x000002F8-0x000002FF Communications Port (COM2) 0x000003E8-0x000003EF Communications Port (COM3) 0x000002E8-0x000002EF Communications Port (COM4) 0x000002F0-0x000002F7 Communications Port (COM5) 0x0000F000-0x0000F03F Intel(R) HD Graphics IBQ800 Series User’s Manual... - Page 65 Programmable interrupt controller 0x000000B8-0x000000B9 Programmable interrupt controller 0x000000BC-0x000000BD Programmable interrupt controller 0x000004D0-0x000004D1 Programmable interrupt controller 0x0000F090-0x0000F097 Standard SATA AHCI Controller 0x0000F080-0x0000F083 Standard SATA AHCI Controller 0x0000F060-0x0000F07F Standard SATA AHCI Controller 0x00000040-0x00000043 System timer 0x00000050-0x00000053 System timer IBQ800 Series User’s Manual...
-
Page 66: Interrupt Request Lines (Irq)
Intel(R) Serial IO GPIO Host Controller - INT3452 IRQ 14 Intel(R) Serial IO GPIO Host Controller - INT3452 IRQ 14 Intel(R) Serial IO GPIO Host Controller - INT3452 IRQ 4294967294 Standard SATA AHCI Controller IRQ 0 System timer IBQ800 Series User’s Manual... -
Page 67: Watchdog Timer Configuration
**endptr; char SIO; printf("Fintek 81804 watch dog program\n"); SIO = Init_F81804(); if (SIO == 0) printf("Can not detect Fintek 81804, program abort.\n"); return(1); }//if (SIO == 0) if (argc != 2) printf(" Parameter incorrect!!\n"); return (1); IBQ800 Series User’s Manual... - Page 68 DisableWDT(void) unsigned char bBuf; Set_F81804_LD(0x07); //switch to logic device 7 bBuf = Get_F81804_Reg(0xFA); bBuf &= ~0x01; Set_F81804_Reg(0xFA, bBuf); //disable WDTO output bBuf = Get_F81804_Reg(0xF5); bBuf &= ~0x20; bBuf |= 0x40; Set_F81804_Reg(0xF5, bBuf); //disable WDT //--------------------------------------------------------------------------- //--------------------------------------------------------------------------- IBQ800 Series User’s Manual...
- Page 69 Init_Finish; F81804_BASE = 0x00; result = F81804_BASE; Init_Finish: return (result); //--------------------------------------------------------------------------- void Unlock_F81804 (void) outportb(F81804_INDEX_PORT, F81804_UNLOCK); outportb(F81804_INDEX_PORT, F81804_UNLOCK); //--------------------------------------------------------------------------- void Lock_F81804 (void) outportb(F81804_INDEX_PORT, F81804_LOCK); //--------------------------------------------------------------------------- void Set_F81804_LD( unsigned char LD) Unlock_F81804(); outportb(F81804_INDEX_PORT, F81804_REG_LD); outportb(F81804_DATA_PORT, LD); Lock_F81804(); IBQ800 Series User’s Manual...
- Page 70 F81804_DATA_PORT (F81804_BASE+1) //--------------------------------------------------------------------------- #define F81804_REG_LD 0x07 //--------------------------------------------------------------------------- #define F81804_UNLOCK 0x87 #define F81804_LOCK 0xAA //--------------------------------------------------------------------------- unsigned int Init_F81804(void); void Set_F81804_LD( unsigned char); void Set_F81804_Reg( unsigned char, unsigned char); unsigned char Get_F81804_Reg( unsigned char); //--------------------------------------------------------------------------- #endif // F81804_H IBQ800 Series User’s Manual...
Need help?
Do you have a question about the IBQ800 Series and is the answer not in the manual?
Questions and answers