Advertisement
Quick Links
Advertisement
Related Manuals for Allen-Bradley Guardmaster 445L-AMSTD2M
Summary of Contents for Allen-Bradley Guardmaster 445L-AMSTD2M
- Page 1 Floor Mounting Column and Cantilever User Manual...
-
Page 2: Important User Information
Important User Information Because of the variety of uses for the products described in this publication, those responsible for the application and use of this control equipment must satisfy themselves that all necessary steps have been taken to assure that each application and use meets all performance and safety requirements, including any applicable laws, regulations, codes and standards. - Page 3 Introduction The Allen-Bradley Guardmaster aluminum mounting stand is offered in a two meter length and is supplied with a floor mounting plate and the hardware necessary to mount the floor plate to the aluminum extrusion as well as leveling hardware for the floor plate. The two meter aluminum extrusion has a cross section of 60 x 60 mm (2.36 x 2.36 in.).
-
Page 4: Step 1: Supplied Parts
Floor Mounting Stand and Cantilever User Manual 445L-AMSTD2M Floor Mounting Stand Step 1: Supplied parts 1 pc. Profile 60 x 60 x 2000 mm (2.4 x 2.4 x 78.7 in.) Floor plate to extrusion mounting hardware 4 pcs. Zinc hexagon socket head cap screws DIN 912 M6 x 25 mm (0.98 in.) 6 pcs. - Page 5 Floor Mounting Stand and Cantilever User Manual Step 3: Leveling hardware Three hexagon socket head cap screws are supplied to level the floor plate. If necessary, premount these screws before attaching the floor plate to the aluminum post. Step 4: Install profile covers Four 300 mm profile covers are supplied with each two meter post to hide the cables.
- Page 6 Floor Mounting Stand and Cantilever User Manual 445L-AMSTDMUT Cantilever—Assembly Steps Step 1: Supplied parts 1 pc. Aluminum profile 60 x 60 x 500 mm (2.4 x 2.4 x 19.7 in.) 1 pc. Black end cap 60 x 60 1 pc. Aluminum cover profiles for hiding cables (300 mm (11.8 in.)) To attach cantilever post to the floor stand post 4 pcs.
-
Page 7: Step 5: Installing Reflector
Floor Mounting Stand and Cantilever User Manual Step 3: Securing 500 mm cantilever to post Hold the cantilever profile between the universal fastening sets. Using a #4 hex tool tighten the hex head screws. Step 4: Installing muting sensors and reflectors Mount the muting sensor to the bracket. - Page 8 Floor Mounting Stand and Cantilever User Manual Step 6: Mount cover profiles Run cables in the slots once the system is complete. Finish the assembly by positioning the profile covers. Using a rubber mallet or a block of material that will not damage the material, lightly tap the cover profiles in place. Dimensions [mm (in.)] 20 (0.79) defined at installation...
- Page 9 Floor Mounting Stand and Cantilever User Manual Original instructions...
- Page 10 Floor Mounting Stand and Cantilever User Manual Original instructions...
- Page 11 Floor Mounting Stand and Cantilever User Manual Original instructions...
- Page 12 GuardShield is a trademark of Rockwell Automation, Inc. www.rockwellautomation.com Power, Control and Information Solutions Headquarters Americas: Rockwell Automation, 1201 South Second Street, Milwaukee, WI 53204 USA, Tel: (1) 414.382.2000, Fax: (1) 414.382.4444 Europe/Middle East/Africa: Rockwell Automation, Vorstlaan/Boulevard du Souverain 36, 1170 Brussels, Belgium, Tel: (32) 2 663 0600, Fax (32) 2 663 0640 Asia Pacific: Rockwell Automation, Level 14, Core F, Cyberport 3, 100 Cyberport Road, Hong Kong, Tel: (852) 2887 4788, Fax: (852) 2508 1846 10000127396 Ver 01 Copyright ©2011 Rockwell Automation, Inc.