Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Northern IP4BIR100
Summary of Contents for Northern IP4BIR100
- Page 1 Rev. 061218...
- Page 2 IP4BIR100 IP Bullet Camera · Quick Start Guide About this Manual This Manual is applicable to IP4BIR100 Network Camera. The Manual includes instructions for using and managing the product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons.
- Page 3 IP4BIR100 IP Bullet Camera · Quick Start Guide Regulatory Information FCC Information FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
- Page 4 IP4BIR100 IP Bullet Camera · Quick Start Guide standards listed under the EMC Directive 2014/30/EU, the RoHS Directive 2011/65/EU 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper...
- Page 5 IP4BIR100 IP Bullet Camera · Quick Start Guide Warnings: Serious injury or death may occur if any of the warnings are neglected. Cautions: Injury or equipment damage may occur if any of the cautions are neglected. Warnings Follow these Cautions Follow these...
- Page 6 IP4BIR100 IP Bullet Camera · Quick Start Guide ● Please make sure that the plug is firmly connected to the power socket. When the product is mounted on wall or ceiling, the device shall be firmly fixed. ● If smoke, odor or noise rise from the device, turn off the power at once and unplug the power cable, and then please contact the service center.
- Page 7 IP4BIR100 IP Bullet Camera · Quick Start Guide ● Do not place the camera in extremely hot, cold (the operating temperature shall be-30°C ~+60°C), dusty or damp locations, and do not expose it to high electromagnetic radiation. ● To avoid heat accumulation, good ventilation is required for operating environment.
-
Page 8: Table Of Contents
IP4BIR100 IP Bullet Camera · Quick Start Guide Table of Contents 1 Appearance Description ..............8 Overview of IP4BIR100 Bullet Camera ......8 2 Installation ..................10 Installation of Memory Card ......... 10 Installation of the Bullet Camera ........12 Installation of Network Cable Water-proof Jacket .. -
Page 9: Appearance Description
IP4BIR100 IP Bullet Camera · Quick Start Guide 1 Appearance Description Overview of IP4BIR100 Bullet Camera... - Page 10 IP4BIR100 IP Bullet Camera · Quick Start Guide Figure 1-1 IP4BIR100 Bullet Camera Table 1-1 Description Description Description Mounting Base Grounding Screw 10/100M Self-adaptive Back Case Ethernet Interface (PoE) Front Case Power Supply (DC 12V) Lens Memory Card Slot Sun Shield Reset Button This type of bullet camera supports PoE power supply.
-
Page 11: Installation
IP4BIR100 IP Bullet Camera · Quick Start Guide 2 Installation Before you start: ● Make sure the device in the package is in good condition and all the assembly parts are included. ● If not using POE, the standard power supply is 12V DC, please make sure your power supply matches with your camera. - Page 12 IP4BIR100 IP Bullet Camera · Quick Start Guide Steps: 1. Unscrew the cover on back case to expose memory card slot. Cover Figure 2-1 Unscrew the Cover 2. Insert the memory card into the memory card slot. Figure 2-2 Insert Memory Card 3.
-
Page 13: Installation Of The Bullet Camera
IP4BIR100 IP Bullet Camera · Quick Start Guide Installation of the Bullet Camera Both wall mounting and ceiling mounting are suitable for the bullet camera. Wall mounting will be taken as an example in this section. You can take steps of wall mounting as a reference if ceiling mounting is adopted. - Page 14 IP4BIR100 IP Bullet Camera · Quick Start Guide Figure 2-4 Secure the Camera to the Ceiling 4. Connect the cables and power on the camera to view live view image. 5. Adjust the surveillance angle. Adjusting Nut Pan: 0° to 360°...
-
Page 15: Installation Of Network Cable Water-Proof Jacket
IP4BIR100 IP Bullet Camera · Quick Start Guide 3). Adjust the tilt direction [0° to 90°]. 4). Rotate the camera [0° to 360°] to adjust the lens to the surveillance angle. 5). Tighten the adjusting nut to complete the installation. - Page 16 IP4BIR100 IP Bullet Camera · Quick Start Guide Components Waterproof Endcap Waterproof Rubber Gasket Lock Nut Network Cable from Router/Switch Align the snap and notch. i. Insert into ⑤ ④ ii. Secure with ⑥ ④ Camera Switch/Router Figure 2-7 Water-proof Accessory Installation...
- Page 17 IP4BIR100 IP Bullet Camera · Quick Start Guide Feed the plugless network cable ⑦ through the lock nut ⑥, waterproof rubber gasket ⑤ (rubber gasket inset ridge must face waterproof endcap), and the water-proof endcap ④ in order. Crimp an RJ-45 network plug ③onto the end of the cable, taking care to insert the twisted pairs of wires in correct order.
-
Page 18: Setting The Network Camera Over The Lan
IP4BIR100 IP Bullet Camera · Quick Start Guide 3 Setting the Network Camera over the Note: You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, please strengthen your own protection. -
Page 19: Activating The Camera
IP4BIR100 IP Bullet Camera · Quick Start Guide Activating the Camera You are required to activate the camera first by setting a strong password for it before you can use the camera. Activation via Web Browser, Activation via SADP, and Activation via Client Software are all supported. -
Page 20: Activation Via Sadp Software
IP4BIR100 IP Bullet Camera · Quick Start Guide Figure 3-3 Activation Interface(Web) 3. Create a password and input the password into the password field. STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including... - Page 21 IP4BIR100 IP Bullet Camera · Quick Start Guide Get the SADP software from the supplied disk or the official website, and install the SADP according to the prompts. Follow the steps to activate the camera, please refer to the User Manual of Network Camera for other two activation methods.
-
Page 22: Modifying The Ip Address
IP4BIR100 IP Bullet Camera · Quick Start Guide STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. - Page 23 IP4BIR100 IP Bullet Camera · Quick Start Guide Steps: 1. Run the SADP software. 2. Select an activate device. 3. Change the device IP address to the same subnet with your computer by either modifying the IP address manually or checking the checkbox of Enable DHCP.
- Page 24 IP4BIR100 IP Bullet Camera · Quick Start Guide Note: You can enable the Guarding Vision service for the device during activation. Refer to Chapter 5.1 for detailed information. 4. Input the admin password and click Modify to activate your IP address modification.
-
Page 25: Accessing Via Web Browser
IP4BIR100 IP Bullet Camera · Quick Start Guide 4 Accessing via Web Browser System Requirement: Operating System: Microsoft Windows XP SP1 and above version CPU: 2.0 GHz or higher RAM: 1G or higher Display: 1024×768 resolution or higher Web Browser: Internet Explorer 8.0 and above version, Apple Safari 5.0.2 and above version, Mozilla Firefox 5.0 and above version and... - Page 26 IP4BIR100 IP Bullet Camera · Quick Start Guide 4. Click Login. Figure 4-1 Login Interface 5. Install the plug-in before viewing the live video and managing the camera. Please follow the installation prompts to install the plug-in. Note: You may have to close the web browser to finish the installation of the plug-in.
-
Page 27: Operating Via Guarding Vision App
IP4BIR100 IP Bullet Camera · Quick Start Guide 5 Operating via Guarding Vision App Purpose: Guarding Vision is an application for mobile devices. With the App, you can view live image of the camera, receive alarm notification and so on. -
Page 28: Enable Guarding Vision Via Web Browser
IP4BIR100 IP Bullet Camera · Quick Start Guide “Privacy Policy” Service” Figure 5-1 Verification Code Setting (SADP) Note: The verification code is required when you add the camera to Guarding Vision app. 3. Click and read "Terms of Service" and "Privacy Policy". - Page 29 IP4BIR100 IP Bullet Camera · Quick Start Guide Steps: 1. Access the camera through web browser. Refer to Chapter 4. 2. Enter platform access configuration interface: Configuration > Network > Advanced Settings > Platform Access Guarding Vision dev.guardingvision.com Figure 5-2 Platform Access Configuration (Web) 3.
-
Page 30: Guarding Vision Setup
IP4BIR100 IP Bullet Camera · Quick Start Guide Guarding Vision Setup Steps: 1. Download and install the Guarding Vision app by searching “Guarding Vision” in App Store or Google Play 2. Launch the app and register for a Guarding Vision user account. - Page 31 IP4BIR100 IP Bullet Camera · Quick Start Guide You can find the QR code on the camera or on the cover of the Quick Start Guide of the camera in the package. Figure 5-4 Scan QR Code Note: If the QR code is missing or too blur to be recognized, you can also...
-
Page 32: Initializing The Memory Card
IP4BIR100 IP Bullet Camera · Quick Start Guide Initializing the Memory Card Steps: Check the memory card status by tapping on the Storage Status in the Device Settings interface. If the memory card status displays as Uninitialized, tap to initialize it.
Need help?
Do you have a question about the IP4BIR100 and is the answer not in the manual?
Questions and answers