Audio Technica BPHS2 User Manual
Audio Technica BPHS2 User Manual

Audio Technica BPHS2 User Manual

Broadcast stereo headset with dynamic boom microphone

Advertisement

BPHS2/BPHS2C/BPHS2S
Broadcast Stereo Headset with Dynamic Boom Microphone /
Broadcast Stereo Headset with Condenser Boom Microphone /
Single-Ear Broadcast Headset with Dynamic Boom Microphone
BPHS2
2
1
6
3
BPHS2C

Part names

Refer to the figures and confirm the parts of the headphones before use.
1 Head pad
2 Headband
3 Slider
4 Housing
5 Arm
6 Earpad

Cleaning the product

Get into the habit of regularly cleaning the product to ensure that it will last for a long time. Do not
use alcohol, paint thinners or other solvents for cleaning purposes.
• To clean, wipe the main unit with a dry cloth.
• Wipe away perspiration and any other dirt from the cable with a dry cloth immediately after
use. Failure to clean the cable may cause it to deteriorate and harden over time, resulting in
malfunction.
• Wipe the plug with a dry cloth if dirty. Failure to clean the plug may cause the sound to cut out and
may cause noise.
• Wipe the earpads and head pad with a dry cloth if dirty. Perspiration or water on the earpads or
head pad may cause discoloration. Wipe with a dry cloth and allow to dry in the shade.
• If the product will not be used for an extended period of time, store it in a well-ventilated place
free from high temperatures and humidity.
• The earpads, head pad, and temple pad are consumable items. They will deteriorate over time
due to use and storage, so replace them when necessary. For information about replacing
earpads, head pad, or other parts, or for information about other serviceable parts, contact your
local Audio-Technica dealer.
User Manual
9
7
ON
OFF
8
5
4
BPHS2S
10
11
7 Limiter switch
8 Gooseneck
9 Dynamic boom microphone
10 Condenser boom microphone
11 Temple pad

Using the product

You can use the microphone on the left or right side of your face by rotating the microphone boom
as shown in the figure.
Windscreen

Positioning the microphone boom

Use the microphone boom and gooseneck to place the microphone in the correct position.
9
20 mm
(0.79")

Using the limiter switch

Use a thin-tipped tool to slide the limiter switch as shown in the figure.
Limiter switch
ONOFF
1
Position the microphone boom so that the
microphone is about 20 mm (0.79") from the tip of
your mouth. Positioning the microphone directly in
front of your mouth will cause popping and other
noise from breathing.
Turning on the limiter switch helps protect your
ears by capping the volume at 105 dB.
105 dB

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the BPHS2 and is the answer not in the manual?

Questions and answers

Summary of Contents for Audio Technica BPHS2

  • Page 1 For information about replacing earpads, head pad, or other parts, or for information about other serviceable parts, contact your local Audio-Technica dealer. 105 dB Turning on the limiter switch helps protect your...
  • Page 2 BPCB2 BPCB3 BPCB2 Cable for BPHS2 (all models) with a TA6F connector at one end and 3-pin XLRM connector and 6.3 mm (1/4") plug at the other. TA6F 3-pin XLRM 3-pin XLRM SLEEVE RING TA6F 6.3 mm (1/4") plug...
  • Page 3: Specifications

    240° 120° Input jack TB6M jack 150° 210° BPHS2: 250 g (8.8 oz), BPHS2C: 240 g (8.5 oz), 180° Weight (without cable) Sound pressure scale is 5 dB per unit BPHS2S: 190 g (6.7 oz) Windscreen x 3, clip, pouch...

This manual is also suitable for:

Bphs2cBphs2s

Table of Contents