Advertisement
TROUBLESHOOTING
T
O PREVENT INJURY
DISCONNECT THE AIR SUPPLY HOSE
,
WHEN ADJUSTING
SERVICING OR
DISASSEMBLING THE TOOL
F
: C
C
IRST
HECK THE
OMPRESSED AIR SUPPLY
Many of problems come from a faulty or inadequate
compressed air supply system. Before attempting to
repair the tool, the following points should be
checked:
• Check the pressure at the output of the compressor;
adjust to 80-100 psi (5.5-7.0 bar) as required.
• Check the tank pressure of the compressor & adjust
the start/stop limits.
• Check the air delivery system; a 3/8" hose is
recommended.
• Use fewer tools simultaneously; do not exceed the
capacity of the compressor or of the delivery
system.
• Drain water from the compressor.
S
: C
ECOND
HECK FOR AIR LEAKS
At rest, this tool should not have any air leaks. Before
attempting to repair the tool and replace parts, check
the following:
• Check all seals in head, valve and piston
assemblies; replace if necessary.
• Check the top edge of main cylinder for burrs or
dents.
• Clean & lubricate the head and valve assemblies;
re-assemble the head assembly carefully.
• Check the interior of the head for scratches.
A more comprehensive list of tips and
hints at
http://ts.primatech.ca/tips
SCHEMATICS
With your tool Serial Number at hand,
go to our support web site to retrieve
the schematic specific to your tool:
http://ts.primatech.ca/145
For more information, contact technical support:
by phone
by email
, ALWAYS
.
1 (800) 363-1962
support@primatech.ca
TOOL WARRANTY AND LIMITATIONS
Primatech warrants that newly purchased fastening
tools, parts and accessories will be free from defects in
material and workmanship (excluding wear parts) for
the period shown below, after the date of purchase by
the original user as evidenced by a valid purchase
invoice.
ONE-YEAR LIMITED WARRANTY will apply to all
parts, except those subjected to normal wear
WARRANTY STATEMENT
Primatech 's sole liability hereunder will be to replace
any part or accessory which proves to be defective
within the specific time period. Any replacement part or
accessories provided in accordance with this warranty
will carry a warranty for the remainder of the period of
warranty applicable to the part it replaces. When repair
or replacement of part or tool is required, the complete
tool or part(s) must be returned to Primatech or at such
authorized warranty service point of Primatech,
transportation prepaid, with a copy of proof of purchase
evidencing that the part or tool is within the warranty
period. Serial # must be intact and legible for warranty
to apply.
This warranty is void as to any tool which has been
subjected to misuse, abuse, accidental or intentional
damage, used with fasteners not meeting Primatech
specifications, size or quality, improperly maintained,
repaired
with
other
than
replacement parts, damaged in transit or handling, or
which, in Primatech 's sole opinion, has been altered,
modified or repaired in a way that affects or detracts
from the performance of the tool.
PRIMATECH MAKES NO WARRANTY, EXPRESSED
OR IMPLIED, RELATING TO MERCHANTABILITY,
FITNESS, OR OTHERWISE, EXCEPT AS STATED
ABOVE, and Primatech's liability AS STATED ABOVE
AND AS ASSUMED ABOVE is in lieu of all other
warranties arising out of, or in connection with, the use
and performance of the tool, except to the extent
otherwise provided for by applicable law.
PRIMATECH SHALL IN NO EVENT BE LIABLE FOR
ANY DIRECT, INDIRECT, OR CONSEQUENTIAL
DAMAGES WHICH MAY ARISE FROM LOSS OF
ANTICIPATED
PROFITS
SPOILAGE OF MATERIALS, INCREASED COST OF
OPERATION, OR OTHERWISE. Any liability, if any,
connected with the use of the tool shall terminate upon
the expiration of the warranty period specified above.
genuine
Primatech
OR
PRODUCTION,
Advertisement
