Related Manuals for Tanda TX7210
Summary of Contents for Tanda TX7210
- Page 1 TX7210 Addressable Single Input/Output Module Installation and Operation Manual TANDA UK Technology Copyright ©2015, All right reserved.
- Page 2 For more information please visit the website at www.recyclethis.info EN54 Part 18 Compliance TX7210 Addressable Single Input/output Module complies with the requirements of EN 54-18:2005. EN54 Standard Conformity Information 0832 TANDA(UK) LIMTIED...
-
Page 3: Table Of Contents
TX7210 Addressable Single Input/Output Module Installation & Operation Manual Table of Content 1 Introduction ................................4 1.1 Overview ................................. 4 1.2 Feature and Benefits ............................. 4 1.3 Technical Specification ..........................4 2 Installation ................................5 2.1 Installation Preparation ..........................5 2.2 Installation and Wiring .......................... -
Page 4: Introduction
1 Introduction 1.1 Overview The TX7210 Addressable Single Input/output Module is characterized as one input or output volt free relay and control module. The unit is normally used for overriding equipment such as lift return, door holder, smoke extract fans, air handling unit, auto dialler to fire brigade, BMS and etc. The unit has built-in feedback signal feature, according to the pre-configured interface module command fire scenario, the alarm controller send out start command to the equipment required to start. -
Page 5: Installation
TX7210 Addressable Single Input/Output Module Installation & Operation Manual 2 Installation 2.1 Installation Preparation This interface module must be installed, commissioned and maintained by a qualified or factory trained service personnel. The installation must be installed in compliance with all local codes having a jurisdiction in your area or BS 5839 Part 1 and EN54. - Page 6 TX7210 Addressable Single Input/Output Module Installation & Operation Manual Figure 2: Input Wiring Details Figure 3: Relay Output Wiring Details Note: Change the parameter Input Check into 3Y (Loop Powered) mostly used (Loop Powered) Figure 5: Control Output with Feedback...
-
Page 7: Interface Module Configuration
TX7210 Addressable Single Input/Output Module Installation & Operation Manual Input/output Parameters Signal Feedback Input Check Output Check Input 3Y (Yes)- Fit with resistor - 4N (No)- No resistor is required -–Default setting Relay Output 1Y (Yes)- By the SELF 2N (No)- By the EXTERNAL –... -
Page 8: Feedback Mode
TX7210 Addressable Single Input/Output Module Installation & Operation Manual Figure 6: Programmer Connection Detail 1. Read Address: 001 Address: 001 2. Write Next Address: 002 3. R/W Config 4. Set Success Fail Figure 9 Figure 7 Figure 8 3.3 Feedback Mode 1. -
Page 9: Input Check Mode
TX7210 Addressable Single Input/Output Module Installation & Operation Manual Parameter Description 1. Read Feedback 1Y 2N 2. Write 1Y Self-Feedback Mode Input Check 3Y 4N 3. R/W Config 2N External-Feedback Mode Output Check 5Y 6N 4. Set (Default) Figure 10 Figure 11 3.4 Input Check Mode... -
Page 10: Read Configuration
TX7210 Addressable Single Input/Output Module Installation & Operation Manual 1. Read Parameter Description Feedback 1Y 2N 2. Write Input Check 3Y 4N 5Y Enable Output Check Mode 3. R/W Config 7 Output Check 5Y 6N 6N Disable Output Check Mode 4. -
Page 11: Troubleshooting Guide
TX7210 Addressable Single Input/Output Module Installation & Operation Manual 5 Troubleshooting Guide What you notice What it means What to do The wiring is loose Conduct maintenance Address not enrolling The address is duplicate Re-Commission the device Unable to commission...
Need help?
Do you have a question about the TX7210 and is the answer not in the manual?
Questions and answers