TSI Instruments MSP 200 User Manual
  1. Manuals
  2. Brands
  3. TSI Instruments Manuals
  4. Industrial Equipment
  5. MSP 200
  6. User manual
TSI Instruments MSP 200 User Manual

TSI Instruments MSP 200 User Manual

Personal impactors
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
PERSONAL IMPACTORS
MODEL 200
USER GUIDE
P/N 6011802, REVISION A
JUNE 2018

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MSP 200 and is the answer not in the manual?

Questions and answers

Related Manuals for TSI Instruments MSP 200

Summary of Contents for TSI Instruments MSP 200

  • Page 1 PERSONAL IMPACTORS MODEL 200 USER GUIDE P/N 6011802, REVISION A JUNE 2018...
  • Page 3 Introduction Unpacking Principle of Operation PERSONAL IMPACTOR Model 200 Personal MODEL 200 Impactor Description Operation Specifications USER GUIDE Spare Parts and Accessories List Technical Contacts Returning for Service References Appendix A: Impactor Flow Calibration Instructions Appendix B: Typical Model 200 Impactor Pressure Drops...
  • Page 4 M a n u a l H i s t o r y The following is a manual history of the Personal Impactors Model 200 User Guide (P/N 6011802). Revision Date June 2018...
  • Page 5 W a r r a n t y Part Number 6011802 / Revision A / June 2018 Copyright TSI Incorporated / 2018 / All rights reserved. Address MSP, A Division of TSI / 5910 Rice Creek Parkway / Shoreview, MN 55126 / USA E-mail Address answers@tsi.com Limitation Of Warranty And Liability...
  • Page 6 SHALL NOT BE RESPONSIBLE FOR INSTALLATION, DISMANTLING OR REINSTALLATION COSTS OR CHARGES. No Action, regardless of form, may be brought against Seller more than 12 months after a cause of action has accrued. The goods returned under warranty to Seller's factory shall be at Buyer's risk of loss, and will be returned, if at all, at Seller's risk of loss.

  • Page 7: Table Of Contents

    C o n t e n t s Manual History .................... ii Warranty ..................... iii Contents ...................... v Introduction ....................1 Unpacking ....................2 Principle of Operation ................2 Model 200 Personal Impactor Description ..........2 Operation ..................... 4 Disassembly Procedure ................4 Coating the Impaction Plate ..............
  • Page 8 (This page intentionally left blank) Personal Impactor Model 200...

  • Page 9: Introduction

    I n t r o d u c t i o n I M P O R T A N T This User Guide contains important safety and operating instructions for the Model 200 Personal Impactor. Any use other than that intended by the manufacturer in this user guide is not proper use of the Model 200 Personal Impactor.

  • Page 10: Unpacking

    U n p a c k i n g Carefully remove the Model 200 Personal Impactor from its shipping box and visually inspect the impactor for any damage it may have suffered in transit. Please contact your shipping company if any damage is noted. The Model 200 Personal Impactor is shipped with this User Guide.
  • Page 11 Figure 2. Schematic Diagram of Personal Impactor. Phillips flat head screws are normally used instead of the spanner screws User Guide...

  • Page 12: Operation

    Figure 3. Model 200 Personal Impactor in Clamping Device Figure 4. Assembled Model 200 Personal Impactor O p e r a t i o n Disassembly Procedure The Model 200 Personal Impactor is disassembled by removing the two screws holding the nozzle cap to the base. Optional spanner screws (flat head with two holes) and matching screw driver could be used for applications where there is a risk of the wearer opening the sampler.

  • Page 13: Assembly Procedure

    tissue to the porous surface. If oil drips from the ring when it is held vertically, too much has been applied. After each use, the particles on the impaction ring should be removed by scraping the surface with a knife or razor blade and, periodically, more oil should be added.

  • Page 14: Specifications

    NO T E The inlet flow rate to the Model 200 Personal Impactor must be measured and controlled to within ±5% of the specified flow rate. The specified cut size for the Model 200 Personal Impactor is valid as long as the required flow rate is maintained by the sampling pump throughout the complete sampling period.

  • Page 15: Technical Contacts

    52068 Aachen GERMANY Telephone: +49 241-52303-0 Fax: +49 241-52303-49 E-mail: tsigmbh@tsi.com Web: www.tsiinc.de TSI Instruments Ltd. Stirling Road Cressex Business Park High Wycombe, Bucks HP12 3ST UNITED KINGDOM Telephone: +44 (0) 149 4 459200 Fax: +44 (0) 149 4 459700 E-mail: tsiuk@tsi.com...

  • Page 16: Returning For Service

    R e t u r n i n g f o r S e r v i c e and complete the on-line “Return Visit our website at http://rma.tsi.com Merchandise Authorization” form or call TSI at 1-800-680-1220 (USA), (651) 490-2860, or 001 651 490 2860 (International) for specific return instructions.

  • Page 17: Appendix A: Impactor Flow Calibration Instructions

    A p p e n d i x A : I m p a c t o r F l o w C a l i b r a t i o n I n s t r u c t i o n s A correct flow calibration of the impactor requires a special attachment known as the Flow Calibration Cap (Figure 5).

  • Page 18: Appendix B: Typical Model 200 Personal Impactor Pressure Drops

    A p p e n d i x B : T y p i c a l M o d e l 2 0 0 P e r s o n a l I m p a c t o r P r e s s u r e D r o p s The table below shows the typical pressure drop that is characteristic for each type of impactor when it is used with a 37-mm glass fiber filter (e.g.
  • Page 19 MSP– Visit our website www.tsi.com for more information. Tel: +1 800 874 2811 India Tel: +91 80 67877200 Tel: +44 149 4 459200 China Tel: +86 10 8219 7688 France Tel: +33 1 41 19 21 99 Singapore Tel: +65 6595 6388 Germany Tel: +49 241 523030 P/N 6011802 Rev.

Table of Contents