Yaesu FTM-350R Technical Supplement page 11

15.Press the [ TFRQ ] key, then rotate the right DIAL
knob to select "100.0 Hz".
16.Press the [ ESC ] key to save the new setting.
17.Press the [ ADJ ] key to set the alignment Menu
Item "MOD xxx MOD xxx MOD xxx". MOD xxx MOD xxx
18.Rotate the left DIAL knob to select "MOD 136H
19.Press the [ ADJ ] key to set the alignment Menu
Item "CTC xxx CTC xxx CTC xxx CTC xxx". CTC xxx
20.Press the PTT switch to activate the transmitter,
adjust the left DIAL knob so that the Deviation
Meter reading is 0.65 kHz ~ 0.75 kHz.
The following steps is USA Version only.
21.Set the transceiver frequency to 223.550 MHz.
22.Press and hold in the [ F ] key for two seconds to
change the [ SMART FUNCTION ] key category to
the "SQL" functions.
23.Press the [ TYPE ] key repeatedly, until the "TONE
ENC" notation appears.
24.Press the [ TFRQ ] key, then rotate the right DIAL
knob to select "100.0 Hz".
25.Press the [ ESC ] key to save the new setting.
26.Press the [ ADJ ] key to set the alignment Menu
Item "MOD xxx MOD xxx MOD xxx MOD xxx". MOD xxx
27.Rotate the left DIAL knob to select "MOD 126H
28.Press the [ ADJ ] key to set the alignment Menu
CTC xxx CTC xxx
Item "CTC xxx CTC xxx". CTC xxx
29.Press the PTT switch to activate the transmitter,
adjust the left DIAL knob so that the Deviation
Meter reading is 0.65 kHz ~ 0.75 kHz.
FTM-350AR/E Technical Supplement
DCS TX Deviation
1. Set the transceiver frequency to 440.050 MHz.
2. Press the [ POW ] key to select "LOW".
3. Press and hold in the [ F ] key for two seconds to
change the [ SMART FUNCTION ] key category to
the "SQL" functions.
MOD 136H MOD 136H MOD 136H".
MOD 136H
4. Press the [ TYPE ] key repeatedly, until the "DCS"
notation appears.
5. Press the [ ESC ] key to save the new setting.
6. Press the [ ADJ ] key to set the alignment Menu
Item "MOD xxx
7. Rotate the left DIAL knob to select "MOD 10EH
8. Press the [ ADJ ] key to set the alignment Menu
Item "DCS xxx
9. Press the PTT switch to activate the transmitter,
adjust the left DIAL knob so that the Deviation
Meter reading is 0.60 kHz ~ 0.80 kHz.
10.Set the transceiver frequency to 146.050 MHz.
11.Press the [ POW ] key to select "LOW".
12.Press and hold in the [ F ] key for two seconds to
change the [ SMART FUNCTION ] key category to
the "SQL" functions.
13.Press the [ TYPE ] key repeatedly, until the "DCS"
notation appears.
MOD 126H MOD 126H". MOD 126H
MOD 126H
14.Press the [ ESC ] key to save the new setting.
15.Press the [ ADJ ] key to set the alignment Menu
Item "MOD xxx
16.Rotate the left DIAL knob to select "MOD 136H
17.Press the [ ADJ ] key to set the alignment Menu
Item "DCS xxx
18.Press the PTT switch to activate the transmitter,
adjust the left DIAL knob so that the Deviation
Meter reading is 0.60 kHz ~ 0.80 kHz.
The following steps is USA Version only.
19.Set the transceiver frequency to 223.550 MHz.
20.Press and hold in the [ F ] key for two seconds to
change the [ SMART FUNCTION ] key category to
the "SQL" functions.
21.Press the [ TYPE ] key repeatedly, until the "DCS"
notation appears.
22.Press the [ ESC ] key to save the new setting.
23.Press the [ ADJ ] key to set the alignment Menu
Item "MOD xxx
24.Rotate the left DIAL knob to select "MOD 126H
25.Press the [ ADJ ] key to set the alignment Menu
Item "DCS xxx
MOD xxx". MOD xxx MOD xxx MOD xxx
DCS xxx DCS xxx
DCS xxx". DCS xxx
MOD xxx". MOD xxx MOD xxx MOD xxx
DCS xxx DCS xxx
DCS xxx". DCS xxx
MOD xxx". MOD xxx MOD xxx MOD xxx
DCS xxx". DCS xxx DCS xxx DCS xxx
Alignment
MOD 10EH MOD 10EH MOD 10EH". MOD 10EH
MOD 136H MOD 136H MOD 136H". MOD 136H
MOD 126H MOD 126H". MOD 126H
MOD 126H
15