Subscribe to Our Youtube Channel
Related Manuals for IBASE Technology IB822 Series
Summary of Contents for IBASE Technology IB822 Series
- Page 1 IB822 Series ® ® Intel Pentium Silver / ® Celeron 3.5” Disk-Size SBC User’s Manual Version 1.0 (Dec. 2018)
- Page 2 No part of this publication may be reproduced, copied, stored in a retrieval system, translated into any language or transmitted in any form or by any means, electronic, mechanical, photocopying, or otherwise, without the prior written consent of IBASE Technology, Inc. (hereinafter referred to as “IBASE”). Disclaimer IBASE reserves the right to make changes and improvements to the products described in this document without prior notice.
-
Page 3: Compliance
0.1% by weight (1000 ppm) except for cadmium, limited to 0.01% by weight (100 ppm). • Lead (Pb) • Mercury (Hg) • Cadmium (Cd) • Hexavalent chromium (Cr6+) • Polybrominated biphenyls (PBB) • Polybrominated diphenyl ether (PBDE) IB822 Series User’s Manual... -
Page 4: Important Safety Information
Danger of explosion if the internal lithium-ion battery is replaced by an incorrect type. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions or recycle them at a local recycling facility or battery collection point. IB822 Series User’s Manual... -
Page 5: Warranty Policy
Software in use (such as OS and application software, including the version numbers) If repair service is required, you can download the RMA form at http://www.ibase.com.tw/english/Supports/RMAService/. Fill out the form and contact your distributor or sales representative. IB822 Series User’s Manual... -
Page 6: Table Of Contents
Connectors Quick Reference ............. 17 2.5.1 eDP Connector (CN1) ............18 2.5.2 Console COM1 RS-232/422/485 Port (CN7) ....... 19 2.5.3 LCD Backlight Connector (J2) ..........20 2.5.4 LVDS Connector (J1, J3) ............. 20 2.5.5 Audio Connector (J4) ............21 IB822 Series User’s Manual... - Page 7 AMI Graphic Output Protocol Policy ........52 4.4.9 Network Stack Configuration ..........53 4.4.10 CSM Configuration ...............54 4.4.11 USB Configuration ..............55 Chipset Settings .................56 4.5.1 South Cluster Configuration ..........56 Security Settings ................60 4.6.1 Secure Boot ................61 Boot Settings ..................63 IB822 Series User’s Manual...
- Page 8 Save & Exit Settings ................64 Appendix ..................65 I/O Port Address Map ................ 66 Interrupt Request Lines (IRQ) ............68 Watchdog Timer Configuration ............69 Onboard Connector Reference Types ..........73 IB822 Series User’s Manual viii...
-
Page 9: Chapter 1 General Information
Chapter 1 General Information The information provided in this chapter includes: • Features • Packing List • Block Diagram • Specifications • Board Overview • Board Dimensions... -
Page 10: Introduction
2 x DDR4-2400 SO-DIMM sockets, expandable up to 8 GB • 1 x HDMI, 1 x DisplayPort, and eDP / 18/24-bit dual-channel LVDS • ® 2 x Intel 211AT PCI-E Gigabit LAN • M.2 B2242 & E2230 slots • Configurable watchdog timer and digital I/O IB822 Series User’s Manual... -
Page 11: Packing List
IBASE provides optional accessories as follows. Please contact us or your dealer if you need any. • Cable Kit (IB76A-1) (including: SATA cable (SATA-53A) Power cable (PW87) COM port cable (PK1H) USB cable (USB-29) • Heatsink (HSIB822-A) • Heat Spreader (HSIB822-1) • Audio cable (Audio-18) IB822 Series User’s Manual... -
Page 12: Specifications
12V: 2.3A 12V: 1.92A Requirement Power DC-In 12 ~ 24V Supply Watchdog Yes (256 segments, 0, 1, 2…255 sec / min) Timer BIOS AMI BIOS iSmart H/W Monitor 102 x 147 mm (4.01” x 5.79”) Dimensions RoHS IB822 Series User’s Manual... - Page 13 Operating: 0 ~ 60 °C (32 ~ 140 °F) • Temperature Storage: -20 ~ 80 °C (-4 ~ 176 °F) • Relative 0 ~ 90 %, non-condensing at 60 °C Humidity All specifications are subject to change without prior notice. IB822 Series User’s Manual...
-
Page 14: Block Diagram
Block Diagram IB822 Series User’s Manual... -
Page 15: Overview
General Information Overview Top View Bottom View Photo of IB822 ＊The photos above are for reference only. Some minor components may differ. IB822 Series User’s Manual... -
Page 16: Dimensions
I/O View Name Name COM1 Port LAN Port HDMI Port USB 3.0 Port DisplayPort Port Dimensions IB822 Series User’s Manual... -
Page 17: Chapter 2 Hardware Configuration
Chapter 2 Hardware Configuration This section provides information on jumper settings and connectors on the board in order to set up a workable system. On top of that, you will also need to install crucial pieces such as the CPU and the memory before using the product. The topics covered are: •... -
Page 18: Installation
Gently push the module in an upright position until the clips of the slot close to hold the module in place when the module touches the bottom of the slot. To remove the module, press the clips outwards with both hands, and the module will pop-up. IB822 Series User’s Manual... -
Page 19: Setting The Jumpers
When two pins of a jumper are encased in a jumper cap, this jumper is closed, i.e. turned On. When a jumper cap is removed from two jumper pins, this jumper is open, i.e. turned Off. IB822 Series User’s Manual... -
Page 20: Jumper & Connector Locations
Jumper & Connector Locations Board diagram of IB822 IB822 Series User’s Manual... -
Page 21: Jumpers Quick Reference
Panel Power Selection eDP / LVDS Panel Seelction Clearing CMOS Data Clearing ME Register ATX / AT Power Selection Factory Use Only JP7, JP9 2.4.1 LVDS Panel Brightness Selection (JP1) Function Pin closed Illustration 3.3V (default) IB822 Series User’s Manual... -
Page 22: Lvds Panel Power Selection (Jp2)
2.4.2 LVDS Panel Power Selection (JP2) Function Pin closed Illustration 3.3V (default) 2.4.3 eDP Panel Power Selection (JP3) Function Pin closed Illustration 3.3V (default) IB822 Series User’s Manual... -
Page 23: Edp / Lvds Panel Selection (Jp4)
Hardware Configuration 2.4.4 eDP / LVDS Panel Selection (JP4) Function Pin closed Illustration LVDS (default) 2.4.5 Clearing CMOS Data (JP5) Function Pin closed Illustration Normal (default) Clear CMOS IB822 Series User’s Manual... -
Page 24: Clearing Me Register (Jp6)
2.4.6 Clearing ME Register (JP6) Function Pin closed Illustration Normal (default) Clear ME 2.4.7 ATX / AT Power Selection (JP8) Function Pin closed Illustration (default) IB822 Series User’s Manual... -
Page 25: Connectors Quick Reference
SATA III Connector with M.2 B2242) LAN Ports USB 3.0 Ports CN5, CN6 DisplayPort HDMI Port DDR4 SO-DIMM Slot J5, J7 M.2 E2230 Slot M.2 B2242 Slot J12 (shared with CN3) Factory Use Only J15, J16 IB822 Series User’s Manual... -
Page 26: Edp Connector (Cn1)
2.5.1 eDP Connector (CN1) Assignment Assignment Ground BL_Power BL_Power Panel_VDD BL_Power Panel_VDD BL_Power Ground AUX_N AUX_P BRIGHTNESS Ground Bklt_en TX0_P Ground TX0_N Ground Ground Ground TX1_P Ground TX1_N Ground Ground IB822 Series User’s Manual... -
Page 27: Console Com1 Rs-232/422/485 Port (Cn7)
DCD, Data carrier detect DSR, Data set ready RX, Receive RTS, Request to send TX, Transmit CTS, Clear to send DTR, Data terminal RI, Ring Indicator ready Ground Assignment RS-232 RS-422 RS-485 DATA- DATA+ Ground Ground Ground IB822 Series User’s Manual... -
Page 28: Lcd Backlight Connector (J2)
LCD Backlight Connector (J2) Assignment Assignment +12V Brightness Control Backlight Enable Ground 2.5.4 LVDS Connector (J1, J3) Assignment Assignment TX0P TX0N Ground Ground TX1P TX1N Ground Ground TX2P TX2N Ground Ground CLKP CLKN Ground Ground TX3P TX3N IB822 Series User’s Manual... -
Page 29: Audio Connector (J4)
Hardware Configuration 2.5.5 Audio Connector (J4) Assignment Assignment Lineout_L Lineout_R JD_FRONT Ground LINEIN_L Linein_R JD_LINEIN Ground MIC_L MIC-R JD_MIC1 Ground 2.5.6 USB 2.0 Connector (J8) Assignment Assignment Ground Ground IB822 Series User’s Manual... -
Page 30: Amplifier Connector (J6)
2.5.7 Amplifier Connector (J6) Assignment Assignment OUTL+ OUTR- OUTL- OUTR+ 2.5.8 SATA HDD Power Connector (J11) Assignment Assignment Ground Ground +12V IB822 Series User’s Manual... -
Page 31: Front Panel Connector (J13)
Orientation is not required when making a connection to this header. • Power LED: Pins 7 and 8 This connector connects to the system power LED on control panel. This LED will light when the system turns on. IB822 Series User’s Manual... -
Page 32: Com2 / Com3 / Com4 Rs-232 Port (J18, J17, J14)
TXD, Transmit data DTR, Data terminal ready Ground DSR, Data set ready RTS, Request to send CTS, Clear to send RI, Ring indicator Not Used 2.5.11 Digital I/O Connector (J19) Assignment Assignment Ground OUT3 OUT1 OUT2 OUT0 IB822 Series User’s Manual... -
Page 33: Dc Power Input Connector (J20)
Hardware Configuration 2.5.12 DC Power Input Connector (J20) Assignment Assignment +12V ~ +24V Ground 2.5.13 Battery Connector (BAT1) Assignment Assignment Battery+ Ground IB822 Series User’s Manual... - Page 34 This page is intentionally left blank. IB822 Series User’s Manual...
-
Page 35: Chapter 3 Drivers Installation
Chapter 3 Drivers Installation This chapter introduces installation of the following drivers: • ® Intel Chipset Software Installation Utility • VGA Driver • HD Audio Driver • ® Intel Trusted Execution Engine Installation • LAN Driver... -
Page 36: Introduction
Follow the instructions below to complete the installation. Insert the disk enclosed in the package with the board. Click Intel on the left pane and Intel(R) Gemini Lake Chipset Drivers on the right. Click Intel(R) Chipset Software Installation Utility. IB822 Series User’s Manual... - Page 37 Driver Installation ® When the Welcome screen to the Intel Chipset Device Software appears, click Next to continue. Accept the software license agreement and proceed with the installation process. On the Readme File Information screen, click Install for installation. The driver has been completely installed. Restart the computer for changes to take effect.
-
Page 38: Graphics Driver Installation
When the the Welcome screen appears, click Next to continue. Click Yes to accept the license agreement and click Next until the installation starts. The driver has been completely installed. Restart the computer for changes to take effect. IB822 Series User’s Manual... -
Page 39: Hd Audio Driver Installation
Driver Installation HD Audio Driver Installation Click Intel on the left pane and then Intel(R) Gemini Lake Chipset Drivers on the right pane. Click Realtek High Definition Audio Driver. On the Welcome screen of the InstallShield Wizard, click Next for installation. -
Page 40: Intel Trusted Execution Engine Drivers
® Intel Trusted Execution Engine Drivers Click Intel on the left pane and then Intel(R) Gemini Lake Chipset Drivers on the right pane. Click Intel(R) TXE Drivers. When the Welcome screen appears, click Next. IB822 Series User’s Manual... - Page 41 Driver Installation Accept the license agreement and click Next. Click Next for installation. As the driver has been sccessfully installed, restart the computer for changes to take effect. IB22 Series User’s Manual...
-
Page 42: Intel Serial Io Drivers
As the Welcome screen to the InstallShield Wizard appears, click Next. Accept the license agreement and click Next. After reading the Readme File, click Next until installation starts. The driver is sccessfully installed, restart the computer for changes to take effect. IB822 Series User’s Manual... -
Page 43: Lan Driver Installation
Driver Installation LAN Driver Installation Click LAN Card on the left pane and then Intel LAN Controller Drivers on the right pane. Click Intel(R) I21x Gigabit Network Drivers.. When the Welcome screen appears, click Next. Accept the license agreement and click Next. IB22 Series User’s Manual... - Page 44 On the Setup Options screen, click the checkbox to select the desired driver(s) for installation. Then click Next to continue. The wizard is ready for installation. Click Install. As the installation is complete, restart the computer for changes to take effect. IB822 Series User’s Manual...
-
Page 45: Chapter 4 Bios Setup
Chapter 4 BIOS Setup This chapter describes the different settings available in the AMI BIOS that comes with the board. The topics covered in this chapter are as follows: • Main Settings • Advanced Settings • Chipset Settings • Security Settings •... -
Page 46: Introduction
These defaults have been carefully chosen by both AMI and your system manufacturer to provide the absolute maximum performance and reliability. Changing the defaults could make the system unstable and crash in some cases. IB822 Series User’s Manual... -
Page 47: 4.3 Main Settings
4.3 Main Settings BIOS Setting Description System Date Sets the date. Use the <Tab> key to switch between the data elements. System Time Set the time. Use the <Tab> key to switch between the data elements. IB822 Series User’s Manual... -
Page 48: 4.4 Advanced Settings
4.4.1 ACPI Computing BIOS Setting Description ACPI Sleep State Selects the highest ACPI sleep state (Suspend Disabled or S3) where the system will enter when the Suspend button is pressed. IB822 Series User’s Manual... -
Page 49: Lvds (Edp/Dp) Configuration
1600 x 1200 / 1680 x 1050 / 1920 x 1080 / 1920 x 1200 Signal Type Allows you to select PWM or DC mode. Brightness Percent Options: 100%, 90%, 75%, 60%, 45%, 30%, 20%, 10% PWM Clock Options: 200 Hz, 1KHz, 5KHz IB822 Series User’s Manual... -
Page 50: Ismart Controller
Temperature Generate the reset signal when system hands Guardian up on POST. Schedule Slots Sets up the hour / minute / day for the power- on schedule for the system. Options: None, Power On, Power On/Off IB822 Series User’s Manual... -
Page 51: Fintek Super Io Configuration
Options: All Enable / Enable Ethernet for WOL / All Disable Serial Ports Sets parameters of serial ports. Configuration Enables / Disables the serial port and select an optimal setting for the Super IO device. IB822 Series User’s Manual... - Page 52 IO = 2E8h; IRQ = 3, 4, 5, 6, 7, 9, 10, 11, 12 Device Mode Changes the serial port mode to: • RS232 • RS485 TX Low Active • RS485 with Termination TX Low Active • RS422 • RS422 with Termination IB822 Series User’s Manual...
- Page 53 IO = 2F8h; IRQ = 3, 4, 5, 6, 7, 9, 10, 11, 12 • IO = 3E8h; IRQ = 3, 4, 5, 6, 7, 9, 10, 11, 12 • IO = 2E8h; IRQ = 3, 4, 5, 6, 7, 9, 10, 11, 12 IB822 Series User’s Manual...
- Page 54 IO = 2E8h; IRQ = 3, 4, 5, 6, 7, 9, 10, 11, 12 • IO = 2F0h; IRQ = 3, 4, 5, 6, 7, 9, 10, 11, 12 • IO = 2E0h; IRQ = 3, 4, 5, 6, 7, 9, 10, 11, 12 IB822 Series User’s Manual...
- Page 55 IO = 2E8h; IRQ = 3, 4, 5, 6, 7, 9, 10, 11, 12 • IO = 2F0h; IRQ = 3, 4, 5, 6, 7, 9, 10, 11, 12 • IO = 2E0h; IRQ = 3, 4, 5, 6, 7, 9, 10, 11, 12 IB822 Series User’s Manual...
-
Page 56: Fintek Super Io Hardware Monitor
PC health status. CPU Shutdown Sets a threshold of temperature to shut down if Temperature CPU goes overheated. Options: Disabled / 70°C / 75°C / 80°C / 85°C / 90°C / 95°C IB822 Series User’s Manual... -
Page 57: Setup
BIOS Setup 4.4.6 M.2 Setup BIOS Setting Description M.2 Select Selects the M.2 interface as SATA or PCIe. IB822 Series User’s Manual... -
Page 58: Cpu Configuration
Management Active Processor Enables / Disables the cores in the processor Cores package. Intel Virtualization When enabled, a VMM can utilize the Technology additional hardware capabilities provided by Vanderpool Technology. VT-d Enables / Disables CPU VT-d. IB822 Series User’s Manual... - Page 59 BIOS Setup 4.4.7.1. Socket 0 CPU Information 4.4.7.2. CPU Power Management Configuration BIOS Setting Description EIST Enables / Disables Intel SpeedStep. Turbo Mode Enables / Disables the turbo mode. IB822 Series User’s Manual...
-
Page 60: Ami Graphic Output Protocol Policy
4.4.8 AMI Graphic Output Protocol Policy BIOS Setting Description Output Select Outputs through HDMI1 interface. IB822 Series User’s Manual... -
Page 61: Network Stack Configuration
If disabled, Ipv4 HTTP boot option will not be created. PXE boot wait time Assigns a period of time to press ESC key to abort the PXE boot. Media detect count Assigns a number of times to check the presence of media. IB822 Series User’s Manual... -
Page 62: Csm Configuration
Options: Adjust, Keep Boot option filter Controls the priority of Legacy and UEFI ROMs. Options: UEFI and Legacy, Legacy only, UEFI only Network Controls the execution of UEFI and Legacy Network OpROM. Options: Do not launch, UEFI, Legacy IB822 Series User’s Manual... -
Page 63: Usb Configuration
The maximum time the device will take before delay it properly reports itself to the Host Controller. Auto uses default value for a Root port it is 100ms. But for a Hub port, the delay is taken from Hub descriptor. IB822 Series User’s Manual... -
Page 64: 4.5 Chipset Settings
Configures HD-audio configuration settings. Configuration PCU Express Controls the PCI Express root port. Configuration SATA Drives Determines how SATA controller(s) operate. USB Configuration Configures XHCI pre-boot driver, XHCI mode, USB VBUS, USB HSIC1, USB disable override, XDCI and XHCI. IB822 Series User’s Manual... - Page 65 Options: Disable / L0s / L1 / L0SL1 / Auto L1 Substates Sets PCIe L1 substates. Options: Disables / L1.1 / L1.2 / L1.1 & L1.2 PME SCI Enables / Disables PME SCI. PCIe Speed Configures the PCIe speed. Options: Auto, Gen1, Gen2 IB822 Series User’s Manual...
- Page 66 4.5.1.3. SATA Drivers BIOS Setting Description SATA Mode Determines how SATA controller(s) operate. Selection SATA Port 0 / 1 Enables / Disables SATA port 0 or port 1. IB822 Series User’s Manual...
- Page 67 USB port from reporting a device connection to the controller. XDCI Support Enables / Disables XDCI. XHCI Disable FALSE makes the XHCI Link Compliance Compliance Mode Mode not disabled. TRUE disables the XHCI Link Compliance Mode. IB822 Series User’s Manual...
-
Page 68: 4.6 Security Settings
Sets an administrator password for the setup Password utility. User Password Sets a user password. Secure Boot Activates when: secure Boot is enabled, Platform Key (PK) is enrolled, System mode is user / depolyed, and CSM is disabled. IB822 Series User’s Manual... -
Page 69: Secure Boot
Customizable Secure Boot mode: In Custom Customization mode, Secure Boot polocy variables can be configured by a physically present user without full authentication. Restore Factory Keys Force System to User Mode. Configure NVRAM to contain OEM-defined factory default Secure Boot keys. IB822 Series User’s Manual... - Page 70 1.) Public Key Certificate in: Signatures / EFI_SIGNATURE_LIST / Forbidden EFI_CERT_XS09 (DER encoded) / EFI- Signatures / CERT_RSA2048 (bin) / Authorized EFI_CERT_SHA256,384,512 TimeStamps / 2.) Authenticated UEFI Variable OsRecovery 3.) EFI PE/COFF Image (SHA256) Signatures Key source: factory, external, mixed IB822 Series User’s Manual...
-
Page 71: 4.7 Boot Settings
Policy boot options. Options: Default, Place First, Place Last Boot mode select Selects a Boot mode, Legacy / UEFI / Dual. Boot Option Priorities Sets the system boot order priorities for hard disk, CD/DVD, USB, Network. IB822 Series User’s Manual... -
Page 72: 4.8 Save & Exit Settings
Restore Defaults Restores / Loads defaults values for all the setup options. Save as User Saves the changes done so far as User Defaults Defaults. Restore User Restores the user defaults to all the setup Defaults options. IB822 Series User’s Manual... -
Page 73: Appendix
Appendix This section provides the mapping addresses of peripheral devices and the sample code of watchdog timer configuration. -
Page 74: I/O Port Address Map
0x0000D000-0x0000DFFF Intel(R) Celeron(R)/Pentium(R) Processor PCI Express Root Port - 5AD9 0x000003F8-0x000003FF Communications Port (COM1) 0x000002F8-0x000002FF Communications Port (COM2) 0x000003E8-0x000003EF Communications Port (COM3) 0x000002E8-0x000002EF Communications Port (COM4) 0x0000E000-0x0000EFFF Intel(R) Celeron(R)/Pentium(R) Processor PCI Express Root Port - 5AD8 IB822 Series User’s Manual... - Page 75 Programmable interrupt controller 0x000000BC-0x000000BD Programmable interrupt controller 0x000004D0-0x000004D1 Programmable interrupt controller 0x0000F000-0x0000F03F Intel(R) HD Graphics 0x0000F090-0x0000F097 Standard SATA AHCI Controller 0x0000F080-0x0000F083 Standard SATA AHCI Controller 0x0000F060-0x0000F07F Standard SATA AHCI Controller 0x00000040-0x00000043 System timer 0x00000050-0x00000053 System timer IB822 Series User’s Manual...
-
Page 76: Interrupt Request Lines (Irq)
Intel(R) I211 Gigabit Network Connection #2 IRQ 4294967285 IRQ 4294967286 ~ Intel(R) I211 Gigabit Network Connection IRQ 4294967291 IRQ 4294967292 Intel(R) Trusted Execution Engine Interface IRQ 4294967293 Intel(R) HD Graphics IRQ 4294967294 Standard SATA AHCI Controller IB822 Series User’s Manual... -
Page 77: Watchdog Timer Configuration
**endptr; char SIO; printf("Fintek 81964 watch dog program\n"); SIO = Init_F81964(); if (SIO == 0) printf("Can not detect Fintek 81964, program abort.\n"); return(1); }//if (SIO == 0) if (argc != 2) printf(" Parameter incorrect!!\n"); return (1); IB822 Series User’s Manual... - Page 78 &= ~0x01; Set_F81964_Reg(0xFA, bBuf); //disable WDTO output bBuf = Get_F81964_Reg(0xF5); bBuf &= ~0x20; bBuf |= 0x40; Set_F81964_Reg(0xF5, bBuf); //disable WDT //--------------------------------------------------------------------------- //--------------------------------------------------------------------------- // THIS CODE AND INFORMATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY IB822 Series User’s Manual...
- Page 79 F81964_BASE = 0x00; result = F81964_BASE; Init_Finish: return (result); //--------------------------------------------------------------------------- void Unlock_F81964 (void) outportb(F81964_INDEX_PORT, F81964_UNLOCK); outportb(F81964_INDEX_PORT, F81964_UNLOCK); //--------------------------------------------------------------------------- void Lock_F81964 (void) outportb(F81964_INDEX_PORT, F81964_LOCK); //--------------------------------------------------------------------------- void Set_F81964_LD( unsigned char LD) Unlock_F81964(); outportb(F81964_INDEX_PORT, F81964_REG_LD); outportb(F81964_DATA_PORT, LD); Lock_F81964(); //--------------------------------------------------------------------------- IB822 Series User’s Manual...
- Page 80 F81964_DATA_PORT (F81964_BASE+1) //--------------------------------------------------------------------------- #define F81964_REG_LD 0x07 //--------------------------------------------------------------------------- #define F81964_UNLOCK 0x87 #define F81964_LOCK 0xAA //--------------------------------------------------------------------------- unsigned int Init_F81964(void); void Set_F81964_LD( unsigned char); void Set_F81964_Reg( unsigned char, unsigned char); unsigned char Get_F81964_Reg( unsigned char); //--------------------------------------------------------------------------- #endif // F81964_H IB822 Series User’s Manual...
-
Page 81: Onboard Connector Reference Types
J18, J17, COM4 RS-232 2DSA DF11-10DS-2C Port Digital I/O Dupon 2.00 mm-pitch Dupon 2.00 mm- Connector pin header (Male) pitch (Female) DC Power Input JST B2P-VH JST VHR-2N Connector Battery Molex 53047-0210 Molex 51021-0200 BAT1 Connector IB822 Series User’s Manual...
Need help?
Do you have a question about the IB822 Series and is the answer not in the manual?
Questions and answers