Table of Contents
Advertisement
Configuring Channelized T1 Cable Length
This completes the trunk card installation procedure. Proceed to the section "Verifying
and Troubleshooting the Installation" to verify the installation.
Verifying and Troubleshooting the Installation
When you first power ON the access server, all LEDs light while the system runs a
series of selftest diagnostics. After the system passes initial diagnostics, all LEDs go
off. Later the LEDs light again as described in earlier in this document.
To complete the installation, verify the trunk card LEDs operate properly by observing
the following LED states:
•
The power LED is ON.
If the power LED remains OFF, verify that the card is seated properly.
If the power LED lights on other trunk cards in the dial shelf, try inserting the trunk
card in a different slot. If none of the power LEDs lights, check your dial shelf
power connections, power entry modules, and ACinput power supplies (if
present).
•
The HCPU LED is ON.
If the HCPU LED is OFF but the power LED is ON, the software image might have
failed to load onto the card. The dial shelf controller will attempt to reload the
software automatically. After a programmed number of attempts to reload the
software image have failed, the dial shelf controller will power OFF the trunk card,
and all LEDs will shut off.
If this happens, assume that the failure is due to defective hardware. Return the
card to the factory for replacement.
•
The FCPU LED is ON.
If the FCPU LED is OFF while the HCPU LED is ON, either the hardware is
defective or the framer processor software has crashed. To determine if the failure
is software related, wait while the dial shelf controller card automatically reloads
the card. The autoreload feature on the dial shelf controller card will attempt to
reload the software image. If the software fails to reload after the programmed
number of times, assume that the failure is due to defective hardware. Return the
card to the factory for replacement.
For further installation troubleshooting information, refer to the Cisco AS5800
Universal Access Server Hardware Installation and Configuration Guide. If you have
any questions, or need assistance, proceed to the section "Cisco Connection Online."
Configuring the CT1 and CE1 Trunk Card
The Cisco 5814 dial shelf only recognizes CT1 and CE1 trunk cards in slots 0 through
5 within the dial shelf chassis; therefore, you must install trunk cards only in the first six
slots.
If you are replacing a trunk card in the same slot as the one you just removed, the
system automatically recognizes the previous system configuration, and no other
configuration is needed.
If you are replacing a trunk card in a different slot from the one you just removed,
additional configuration is needed. Refer to the Cisco AS5800 Universal Access
Server Software Installation and Configuration Guide to configure the CT1 and CE1
interfaces.
FCC Compliance
Regulatory compliance and safety information for the Cisco AS5800 Universal Access
Server is contained in the Regulatory Compliance and Safety Information document
that shipped with your system.
Cisco Connection Online
Cisco Connection Online (CCO) is Cisco Systems' primary, realtime support channel.
Maintenance customers and partners can selfregister on CCO to obtain additional
content and services.
Available 24 hours a day, 7 days a week, CCO provides a wealth of standard and
valueadded services to Cisco's customers and business partners. CCO services
include product information, software updates, release notes, technical tips, the Bug
Navigator, configuration notes, brochures, descriptions of service offerings, and
download access to public and authorized files.
CCO serves a wide variety of users through two interfaces that are updated and
enhanced simultaneously—a characterbased version and a multimedia version that
resides on the World Wide Web (WWW). The characterbased CCO supports
Zmodem, Kermit, Xmodem, FTP, and Internet email, and is excellent for quick access
to information over lower bandwidths. The WWW version of CCO provides richly
formatted documents with photographs, figures, graphics, and video, as well as
hyperlinks to related information.
You can access CCO in the following ways:
•
WWW: http://www.cisco.com
•
WWW: http://wwweurope.cisco.com
•
WWW: http://wwwchina.cisco.com
•
Telnet: cco.cisco.com
•
Modem: From North America, 408 5268070; from Europe, 33 1 64 46 40 82. Use
the following terminal settings: VT100 emulation; databits: 8; parity: none; stop
bits: 1; and connection rates up to 28.8 kbps.
For a copy of CCO's Frequently Asked Questions (FAQ), contact ccohelp@cisco.com.
For additional information, contact ccoteam@cisco.com.
Advertisement
Table of Contents
