Summary of Contents for Kitchen and Home 5-ZG-36-SS
- Page 1 Instruction Manual Built-In Gas Cooktop 5-ZG-36-SS, 5-ZG-36-SS-LPG 5-ZSS-36X, 5-ZSS-36X-LPG 4-GCW, 4-GCW-LPG 5-GCW, 5-GCW-LPG 2-GCW , 2-GCW-LPG 2-SSW , 2-SSW-LPG...
- Page 2 BEFORE YOU BEGIN Read this manual completely and carefully. Installation of this cooktop must conform with local codes, or in the absence of local codes, with the National Fuel Gas Code. This appliance is ETL certified by Intertek. Note to Consumer: Keep the manual for future reference.
-
Page 3: Table Of Contents
Contents 1. Close-up view..................04 2. Using your cooktop................05 3. Cleaning…………………………………..........06 4. Useful tips……..................07 5. Troubleshooting…................08 6. Installation …....……………............09 7. Burners and nozzle specifications ...........13 8. Different types of gas …..............15... -
Page 4: Close-Up View
Congratulations for choosing this appliance, which you will find dependable and very easy to use. This manual will explain how to achieve the best performance and also extend the life of your appliance. Thank you Close-up View 5-ZG-36-SS, 5-ZG-36-SS-LPG, 5-ZSS-36X, 5-ZSS-36X-LPG 5-GCW, 5-GCW-LPG 4-GCW, 4-GCW-LPG 2-GCW , 2-GCW-LPG , 2-SSW , 2-SSW-LPG... -
Page 5: Using Your Cooktop
1. Small burner 2. Medium burner 3. Large burner 4. X Large wok burner 5. Ignitor 6. Safety device - If the flame accidentally goes out (spills, drafts, etc.), it stops the delivery of gas to the burner. 7. Control knobs Using your cooktop Gas Burners Position of the corresponding gas burner is indicated on each control knob. -
Page 6: Cleaning
Cleaning Before cleaning or performing maintenance of your gas cooktop, you must disconnect it from the electrical power supply (electrical outlet or battery). To make sure your cooktop performs properly and safely for a long time, it is extremely important to clean it carefully, thoroughly and often. Please keep in mind the following: ●... -
Page 7: Useful Tips
Useful tips Using the burners For best performance, follow these general guidelines: Use the appropriate cookware for each burner (see table) in order to prevent the flame from reaching the ● side of the pot or pan. Always use cookware with a flat bottom and keep the lid on. ●... -
Page 8: Troubleshooting
Troubleshooting First, check and confirm there are no interruptions to the gas and electrical lines. The burner can’t be ignited or the flame is not uniform around the burner. Check to make sure that: The gas holes on the burner are not clogged. ●... -
Page 9: Installation
If you cannot contact your gas supplier, call the fire department. Installation and service must be performed by a qualified installer, service agency or the gas supplier. Countertop cut out requirements Model Opening size 5-ZG-36-SS 5-ZG-36-SS-LPG 840x480mm 5-ZSS-36X 5-ZSS-36X-LPG 4-GCW, 4GCW-LPG... - Page 10 Installation Instructions The following instructions are for the qualified installer, so the installation and maintenance procedures can be done in the most professional and expert manner. Important: Unplug the electrical connection before performing any maintenance work. Positioning of gas cooktop Important: this unit may be installed and used only in permanently ventilated rooms.
- Page 11 Installation of built-in gas cooktop Cooktop can be installed in a kitchen, dinning room or any other dry room. ● Included hardware (hooks, screws) will secure the cooktop to surrounding surfaces, 20 to 40 mm in ● thickness Hook position for Hook position for Hook position for H=20mm top...
- Page 12 Important: If the cooktop is being installed on a built-in oven, the oven should be placed on two wooden strips and if ● placed on interior cabinet surface, remember to leave an opening of at least 45 x 560 mm from the back side.
-
Page 13: Burners And Nozzle Specifications
Connection to flexible steel tube Gas feeding connector is threaded 1/2" for round gas pipe. Only use pipes and gaskets that conform to ● the current standards. The maximum length of the flexible pipes must not exceed 2000mm/79.74”. ● Once the connection has been done, make sure that the flexible metal tube does not touch any moving ●... - Page 14 Valve adjustment Valve adjustment should be done with the control knob set at Burner ON small/low flame position. ● Remove the knob, and adjust the flame with a tiny screwdriver. ● To check the adjusted flame, start the burner and run it in the high setting for 10 minutes. Then turn the knob into the low setting.
-
Page 15: Different Types Of Gas
Different types of gas TABLE 2: Settings for different types of gas Nozzle Pressure Nominal Charge Reduced Charge diameter Burner mbar 1/100mm kcal/h kcal/h 2800 12.5 — 0.40 Small 2800 66.5 — 0.40 5000 12.5 — 1268 0.60 Medium 1268 5000 —...