Advertisement
Table of Contents
The explosion proof dock fan/light combination unit arrives in several parts for shipping. Follow the steps below
to assemble the unit.
The explosion proof dock fan / light has been disassembled in three parts.
1
1. Dock Mount Adjustable Arm
2. Explosion Proof Fan / Explosion Proof Camera Assembly
3. Mounting Pole for Explosion Proof Fan
Tools required:
•
Drill / Wrench (9/16" & 7/16")
Additional help for maneuvering unit is also necessary.
All bolting hardware is pre-place on the unit. Remove the bolts / nuts /
washers prior to attaching each part.
1. Locate all pieces shipped with the unit.
2. Install Mounting Pole to Explosion Proof Fan.
a. Locate and remove bolts already attached to base of fan.
b. Place flat side of mounting pole into receiving base of the
(FIGURE B)
fan.
c. Use a 9/16" wrench for the top bolt & 7/16" for the bottom
adjustment bolt.
Note: Adjust fan to the desired angle after installation.
3. Install Dock Mount Adjustable Arm to surface. This can be
installed to the surface before step 4 or after step 5. Note: The fan
and light will add weight to the dock mount.
a. There are six pre-drilled mounting holes available for
mounting dock mount to the surface.
b. Utilize all six mounting holes to secure dock mount to
surface. The explosion proof unit is heavy, therefore; the
surface and hardware used MUST be capable of
supporting the weight.
Larson Electronics, LLC
Assembly Guide
Explosion Proof Dock Fan/Light Combination
with Adjustable Arm - 24" Fan - 12W LED Lamp
(FIGURE C)
Phone: (800) 369-6671
2
(FIGURE A)
(FIGURE D)
Fax: (903) 498-3364
EPL-DL-24-12W-WF.24
3
9/16"
www.larsonelectronics.com
A
B
7/16"
C
D
1 of 2
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Larson Electronics EPL-DL-24-12W-WF.24
Summary of Contents for Larson Electronics EPL-DL-24-12W-WF.24
- Page 1 Utilize all six mounting holes to secure dock mount to surface. The explosion proof unit is heavy, therefore; the surface and hardware used MUST be capable of supporting the weight. Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com...
- Page 2 Position light in the desired (FIGURE G) direction before tightening bolt. b. The bolt used for the light is the same used for the fan as (FIGURE H, I). shown in Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com 2 of 2...
-
Page 3: Operation
Adjustable Arm - 24" Fan - 12W LED Lamp Instruction Guide Thank you for your purchase of the Larson Electronics EPL-DL-24-12W-WF.24 Explosion Proof Dock Fan/Light Combination with Adjustable Arm. This dock light / fan comes disassembled for shipping. See Assembly Guide for assembling the unit. -
Page 4: Tilt Adjustment
The Cable is not frayed and is gripping tightly in all points of cable contact. The Cable Jacket is completely intact and that no internal conductors or conductor insulation is exposed. Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com... -
Page 5: Troubleshooting Fan
If you do not have that information, please contact Larson Electronics by phone 1-800-369-6671 or email sales@larsonelectronics.com for further assistance. Please visit LarsonElectronics.com for Warranty and Return information. Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com...
Need help?
Do you have a question about the EPL-DL-24-12W-WF.24 and is the answer not in the manual?
Questions and answers