VIETA VC-HD900BL User Manual page 31

right; the other icons are same as ones in the unit
panel or in the Remote Control.
In menu set interface, you can adjust MUTE, APS,
EQ, TA, AF, PTY as right.
2. Band Button
In RADIO mode, press the BAND button on the
remote control to select your desired radio band of
FM1, FM2, FM3, AM1 and AM2, and the word means
which band is selected will be displayed on the small
monitor of the front panel.
3. TUNE/SEEK UP/DOWN Buttons
In RADIO mode:
1) Press and hold the >>|/|<< button to
automatically search up/down for an available station
fromcurrent frequency.
2) Briefly press the >>| / |<< button to manually
search up or down with step by step for your desired
station from the current frequency.
4. APS Button
In RADIO mode:
1)When pressing and holding the APS button,the
radio searches fromthe lowest frequency and checks
the signal strength level until 1 cycle search is
finished. And then the 6 strongest stations are preset
to the corresponding preset number memory bank.
The AS operation is implemented in the each bank of
the selected band. When the AS operation is finished,
it will scan each preset station for 5 seconds in FMor
AMband fromM1 as briefly pressing APS button.
After finishing a circle of scanning , it will resume
broadcasting on the M1.
(It can store 3x6 stations for FMand 2x6 stations for
AMin all)
2) When briefly pressing the APS button, the radio
will scan each preset station for 5 seconds in FMor
AMband fromM1. After finishing a circle of scanning,
it will resume broadcasting on the M1.
NOTE: In FMband, FM1,FM2,FM3 is checked one at
a time; In AMband,AM, AM1, AM2 is checked one at a
time.
5. PRESET STATION [ 1-6 ] BUTTONS
In RADIO mode:
1) To memorize the current frequency on the current
band, press and hold any one of the six preset
buttons (1-6) on remote control or rotate number
knob and long press it .
2) To recall the preset memory on the current band,
press one of the preset buttons [1-6] on remote
control or rotate number knob and press it .
6. STEREO/MONO BUTTON
Press the ST button on the remote control to select
the STEREO or MONO sound mode for FMband.
7. LOC BUTTON
1) In RADIO mode, when the signals of the distant
radio stations are very weak and the receiving effect
is bad during tuning, check whether there is the word
LOC on LCD. If there is the word LOC on LCD, press
this button to turn off the LOC function, then tune
again for the distance radio station;
2) In RADIO mode, when the signals of the local radio
stations are too strong this causes interference to the
receiving effect during tuning, press this button to
turn on the LOC function to display the word LOC on
LCD, then tune again for the local radio station.
PTY MUSIC group- - PTY SPEECH group -- OFF PTY
group is on, PTY group is on, pressing the 6 number
buttons also can select one of PTY programs as
above.
8. PTY (PROGRAMTYPE) BUTTON
Press the PTY button briefly to select one of the
following modes:
When press the VOL+ or VOL- button on the remote
control or rotate the VOL knob on the front panel to
select one of PTY programs as follows:
<-->NEWS<-->AFFAIRS<-->INFO<-->SPORT<-
->EDUCATE<-->DRAMA <-->CULTURE<--
>SCIENCE<--> VARIED<-->WEATHER<-->
FINANCE <-->CHILDREN<-->SOCIAL<-
->RELIGION<-->PHONE IN<-->TRAVEL
<-->LEISURE<-->DOCUMENT< -->PTY NONE<-
->POP M< -->ROCK M <-->EASY M<-->LIGHT
M<--> CLASSICS<-->OTHER M<-->JAZZ
<-->COUNTRY<-->NATION M<-->OLDIES<--
>FOLK M<-->
When After selecting one of the PTY programs, it will
display SEEK PTY and automatically search for the
station of the PTY program. If the station of the PTY
program does not exist, it will display PTY NONE and
then return back to the normal station.
31