Table of Contents
Advertisement
OPERATOR'S
MANUAL
Coronet / 400 / 2400 Series
13HP Hydro Riders
Mfg. No.
Description
1694462
Coronet, 13HP Hydro
1694464
2413H, 13HP Hydro
1694510
Coronet, 13HP Hydro (CE)
1694512
RT1330, 13HP Hydro
1694514
RT1330, 13HP Hydro (CE)
1694536
2413H, 13HP Hydro (CE)
16HP Hydro Riders
Mfg. No.
Description
1694463
Coronet, 16HP Hydro
30" Mower Decks
Mfg. No.
Description
1692543
30" Mower Deck
1694053
30" Mower Deck
1694511
30" Mower Deck (CE)
1694513
30" Mower Deck
1694515
30" Mower Deck (CE)
1694537
30" Mower Deck
34" Mower Decks
Mfg. No.
Description
1692545
34" Mower Deck
Revision No. 01
Rev. Date 11/2003
TP 100-3909-01-CO-SMAN
1726339-01
Advertisement
Table of Contents
Troubleshooting
Related Manuals for Simplicity 400 / 2400
Summary of Contents for Simplicity 400 / 2400
- Page 1 OPERATOR’S MANUAL Coronet / 400 / 2400 Series 13HP Hydro Riders Mfg. No. Description 1694462 Coronet, 13HP Hydro 1694464 2413H, 13HP Hydro 1694510 Coronet, 13HP Hydro (CE) 1694512 RT1330, 13HP Hydro 1694514 RT1330, 13HP Hydro (CE) 1694536 2413H, 13HP Hydro (CE) 16HP Hydro Riders Mfg.
-
Page 2: Table Of Contents
Identification Numbers...2 Safety Rules & Information...3 Safety Decals ...6 Features & Controls ...8 Control Functions ...8 Safety Interlock System ...10 Operating the Rider ...10 General ...10 Adding Fuel ...10 Checks Before Starting ...10 Brake Pedal Operation...11 Starting The Engine ...11 Selecting Ground &... -
Page 3: Identification Numbers
K. Vibration at the Steering Wheel * L. Vibration at the Seat * M. Combination Number This unit complies with European Harmonized Lawn Mower Standard EN 836, European Machinery Directive 98/37/CE, and European EMC Directive 89/336/CE * Tested according to EN 836:1997/A2:2001, EN 1032:... -
Page 4: Safety Rules & Information
Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment. This mowing deck is capable of amputating hands and feet and throwing objects. The triangle in text signifies important cautions or warnings which must be followed. -
Page 5: Safety Rules And Information
Safety Rules and Information SLOPE OPERATION Slopes are a major factor related to loss-of-control and tip- over accidents, which can result in severe injury or death. Operation on all slopes requires extra caution. If you can- not back up the slope or if you feel uneasy on it, do not operate on it. - Page 6 SERVICE AND MAINTENANCE Safe Handling of Gasoline 1. Extinguish all cigarettes, cigars, pipes, and other sources of ignition. 2. Use only approved gasoline containers. 3. Never remove the gas cap or add fuel with the engine running. Allow the engine to cool before refueling. 4.
-
Page 7: Safety Decals
Safety Decals SAFETY DECALS This unit has been designed and manufactured to pro- vide you with the safety and reliability you would expect from an industry leader in outdoor power equipment manufacturing. Although reading this manual and the safety instructions it contains will provide you with the necessary basic knowledge to operate this equipment safely and effec- tively, we have placed several safety labels on the unit to... -
Page 8: Ce Safety Icons
SAFETY ICONS Warning: Read Operator’s Manual. Read and understand the Operator’s Manual before using this machine. Danger: Thrown Objects. This machine is capable of throwing objects and debris. Keep bystanders away. Warning: Remove Key Before Servicing. Remove the key and consult techni- cal literature before performing repairs or maintenance. -
Page 9: Features & Controls
Features & Controls CONTROL FUNCTIONS The information below briefly describes the function of individual controls. Starting, stopping, driving, and mowing require the combined use of several controls applied in specific sequences. To learn what combination and sequence of controls to use for various tasks see the OPERATION section. Throttle/Choke Control (Single Lever Models) The throttle/choke lever controls engine speed and... - Page 10 Fuel Tank To remove the cap, turn counterclockwise. PTO Switch The PTO (Power Take-Off) switch engages and disen- gages attachments that use the PTO. To engage the PTO, pull UP on the switch. Push DOWN to disengage. Note that the operator must be seated firmly in the trac- tor seat for the PTO to function.
-
Page 11: Safety Interlock System
Operating the Rider SAFETY INTERLOCK SYSTEM This unit is equipped with safety interlock switches and other safety devices. These safety systems are present for your safety, do not attempt to bypass safety switches, and never tamper with safety devices. Check their operation regularly. Operational SAFETY Checks Your unit is equipped with a seat switch safety system. -
Page 12: Brake Pedal Operation
BRAKE PEDAL OPERATION 1. See Figure 2. Depressing the pedal from position A to B disengages the transmission drive and also returns the transmission control lever to neutral (from forward speeds). Fully depressing the pedal to position B applies the rider brake. 2. -
Page 13: Selecting Ground & Engine Speed
Operating the Rider SELECTING GROUND & ENGINE SPEED Ground speed is selected by depressing the clutch/brake pedal (D, Figure 4) and moving the control lever (C, Figure 4) to the appropriate speed selection. If the ter- rain is rough, hilly or sloping, use first or second gear. If the grass is wet or over 3”... -
Page 14: Operating The Mower
WARNING Make certain direction of travel is clear of objects, people and animals. Always look DOWN AND BEHIND before backing! OPERATING THE MOWER 1. When traveling to or from the work site, fully raise the mower using the mower lift lever (A, Figure 4). At the work site, lower mower using the lift lever. -
Page 15: Mower Removal And Installation
Operating the Rider *2396 Figure 7. Mower Removal/Installation (34” mower shown) A. Idler Pulley Arm B. Idler Pulley C. PTO (Electric Clutch) Pulley WARNING Stop engine and remove key. Do not engage PTO until mower is completely removed or installed and operator is seated. -
Page 16: Storage
STORAGE WARNING Never store the unit (with fuel) in an enclosed, poorly ventilated structure. Fuel vapors can travel to an ignition source (such as a furnace, water heater, etc.) and cause an explosion. Fuel vapor is also toxic to humans and animals. Before you store your unit for the off-season, read the Maintenance and Storage instructions in the Safety Rules section, then perform the following steps:... -
Page 17: Regular Maintenance
Regular Maintenance MAINTENANCE SCHEDULE & PROCEDURES The following schedule should be followed for normal care of your rider and mower. SAFETY ITEMS Check Safety Interlock System Check Tractor Brakes Check Mower Blade Stopping Time TRACTOR MAINTENANCE ITEMS Check Tractor/Mower for loose hardware Lubricate Rear Axle Shafts Clean Battery &... -
Page 18: Raising The Seat Deck
RAISING THE SEAT DECK To gain access to the engine compartment, simply tilt the seat deck forward. ADDING FUEL To add fuel: 1. Remove the fuel cap (A, Figure 10). 2. Fill the tank. Do not overfill. Leave room in the tank for fuel expansion. -
Page 19: Lubrication
Regular Maintenance LUBRICATION Lubricate the rider and mower as shown in Figures 11 - 16. When a grease gun is shown, wipe the fitting clean, apply two or three shots of lithium base automotive grease, and wipe off excess grease. When an oil can is shown, wipe the area clean, apply a few drops of oil (SAE 30), then wipe up drips or spills. -
Page 20: Battery Maintenance
BATTERY MAINTENANCE WARNING When removing or installing battery cables, disconnect the negative cable FIRST and reconnect it LAST. If not done in this order, the positive terminal can be shorted to the frame by a tool. Cleaning the Battery and Cables Service Interval: Every 100 Hours 1. -
Page 21: Servicing The Mower Blades
Regular Maintenance SERVICING THE MOWER BLADES WARNING For your personal safety, do not handle the sharp mower blades with bare hands. Careless or improper handling of blades may result in serious injury. 1. Remove mower from the rider. 2. Blades should be sharp and free of nicks and dents. If not, sharpen blades as described in following steps. -
Page 22: Troubleshooting, Adjustments & Service
TROUBLESHOOTING While normal care and regular maintenance will extend the life of your equipment, prolonged or constant use may eventually require that service be performed to allow it to continue operating properly. The troubleshooting guide below lists the most common problems, their causes and remedies. -
Page 23: Troubleshooting The Mower
Troubleshooting, Adjustment & Service Troubleshooting the Rider (Continued) PROBLEM Engine runs, but rider will not drive. Rider drive belt slips. Brake will not hold. Rider steers hard or handles poorly. TROUBLESHOOTING THE MOWER PROBLEM Mower will not raise. Mower cut is uneven. Mower cut is rough looking. -
Page 24: Seat Adjustment
WARNING To avoid serious injury, perform adjustments only with engine stopped, key removed and rider on level ground. SEAT ADJUSTMENT Use the lever on the front of the seat (A, Figure 22) on to adjust the seat forward or rearward for best rider com- fort. -
Page 25: Brake Adjustment
Adjustments BRAKE ADJUSTMENT Brake Adjustment 1. Release the parking brake. 2. Brake arm (C, Figure 25) should be touching stop (B). 3. Remove cotter pin (D) and loosen the castle nut (A). Place a 0.015” feeler gauge (E) gap between the brake disc (F) and the brake puck (G). -
Page 26: Mower Adjustments
MOWER ADJUSTMENTS If the cut is uneven, the mower may need leveling. Unequal or improper tire pressure may also cause an uneven cut. Make sure tire pressure is correct as speci- fied in Checking Tire Pressure. To achieve proper mower levelling, perform Side-To-Side Leveling, Front-To-Back Leveling and Transport Height Adjustment procedures, in order, as follows. - Page 27 Adjustments Figure 28. Leveling The Mower Side-to-Side A. Nut B. Eccentric Nut C. Rear Rollers Front-To-Back Leveling 1. Make sure mower is level side-to-side and that rear rollers are on the ground. 2. Position blade(s) front-to-back. Measure the distance from the ground to front tip of blade(s), and from ground to rear tip of blade(s).
-
Page 28: Battery Charging
Transport Height Adjustment Transport height should be adjusted so that rear mower rollers are 1/8” - 1/4” (3-6 m) above ground when mower lift lever is in transport position. To adjust, perform both mower leveling procedures first, then do the following procedure. -
Page 29: Rider Drive Belt Replacement
Belt Replacement To avoid damaging belts, DO NOT PRY BELTS OVER PULLEYS. RIDER DRIVE BELT Replacement of the rider drive belt requires removal of the transmission and carrier frame. Should the drive belt ever fail, contact your dealer for replacement. MOWER BELT - 30”... -
Page 30: Specifications
NOTE: Specifications are correct at time of printing and are subject to change without notice. ENGINE 13 HP Intek OHV — Briggs & Stratton Horsepower 13 HP @ 3400 rpm Displacement 21 Cu. In. (344 cc) Electrical 12 Volt, 3 Amp D.C. Battery 230 CCA Air Cleaner Pre-Cleaned Air to Paper Filter Oil Capacity... -
Page 31: Parts & Accessories
Parts & Accessories REPLACEMENT PARTS Replacement parts are available from your authorized dealer. Always use genuine Simplicity Service Parts. MAINTENANCE ITEMS Many convenient and helpful service and maintenance items are available from you authorized dealer. Some of these items include: Engine Oil Tire Sealant Touch-Up Paint... -
Page 32: Lawn Care
HOW AND WHEN TO WATER, FERTILIZE & AERATE Most lawns are watered too often, but with too little water. However too much water can allow develop- ment of diseases with your lawn. It is best to water the lawn only when necessary, and then to water it slowly, evenly, and deeply—imitat- ing a slow, soaking rain. -
Page 33: Lawn Care & Mowing Information
Lawn Care & Mowing Information PROPER MOWING SPEED ENGINE SPEED & GROUND SPEED Always operate the engine at full throttle when mowing. If you hear the engine slowing down, you are mowing too fast—maintaining a slower ground speed will improve the cutting efficiency of the blades and prevents many com- mon cutting problems. - Page 34 M A N U F A C T U R I N G , I N C . 500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 www.simplicitymfg.com © Copyright 2003, Simplicity Manufacturing, Inc. All Rights Reserved. Printed in USA.